similar to: E400P

[ZapRAS triggering a kernel panic] >> Kernel panic: Aiee, killing interrupt handler! >> In interrupt handler - not syncing >> HDLC Receiver overrun on Channel Tor2/0/2/25 (master: Tor2/0/2/25) > > Hrm, I haven't seen this before. Please contact me off-list and I'll > give you more debugging instructions that may be helpful, as well as > enquire additionally

hi All, quit new to asterisk, can anybody tell me whether Wildcard E400P and Wildcard E100P support R2 CAS protocol. if they do, what is the value, i should set to 'signalling' parameter in the zapata.conf file? Surajee -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, Can someone send me a sample on how to get an E400P working with ISDN PRI signaling? What conf. files must I edit? thanks in advance Eduardo

I just recently purchased an E400P card and am attempting to get it working. My requirements are for 2 ports to run Q.931 and the other 2 ports to run R2 signalling with DTMF inband. The card will operate in a drop and insert fashion with calls arriving on the ISDN side and being terminated on the R2 lines. There don't seem to be any examples out there of how to set up this card for R2

Hi, is there anyone who have experience with more as one card in one machine ? Or, somebody from the Digium team who can make an assertion about this ? Regards, Thomas.

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'm trying to connect an E400P card to a Siemens Digital ISDN S2M Module. (TMS2). How should I connect these two? Straight or crossed? (receive tip <-> receive tip or receive tip <-> transmit tip) Also, I can't seem to figure out how to configure the channels. Does anyone here have any experience with the Siemens module

A brandly new E400P 128 channel PRI, you can find more information on the Digium's site. The card was not used before, I sell it cause our company just don't need, we use Cisco AS5300. I can offer you the PCI PRI at $940 if bought in the next 2 days, I can send it to you via FedEx or DHL express. Please email me for more details! Regards, Kalin ----------------------------- IPPN Networks

asterisk-users This card did not connect with E1 line? how to configure this card? When calling ,showing error: app_dial.c:764 dial_exec: Unable to create channel of type 'Zap' thanks a lot :) dev2002 dev2002@163.com 2005-07-28

Hi everybody. We have a problem with the configuration of the card, the cards work and we receive incoming calls but asterisk don't receive dnid. We have 5 servers with 1 E400P with the same problem and the telco told us that we need to configure the card to request it, how we can do this? Can you help me to solve the problem. Best regards, Carlos Fernández Puente carlos.fernandez@alisys.net

asterisk-users Any help will be appreciated. This card did not connect with E1 line how to loop E400P card to test ? now I loop the card. span 1 ---span2 RJ45 pins 1--4 2--5 but show : When calling ,showing error: app_dial.c:764 dial_exec: Unable to create channel of type 'Zap' Asterisk Ready. *CLI> -- Registered SIP '2002' at 192.168.139.59 port 3289 expires 120

Hi, I came back from a quiet weekend today and found my E400P box to have gone astray. Asterisk is loaded from inittab, and started crashing and reloading a couple of thousands of times, each time notifying my monitoring service :-P I remember there would be issues on old cvs stuff since the crash at digium so I made a clean checkout just now. Here is what happens when I load manually:

Hi, I found E400P quad PRI card quite cheap (749USD): http://www.govarion.com/product_info.php?cPath=1&products_id=2&osCsid=68cdd6e3d08754 in comparison to te410p (approx 1500 USD ) http://www.digium.com/index.php?menu=product_detail&category=hardware&product=TE410P Now newer generation with HW echo canceling emerged (te411p). I'm not sure in what things those two cards

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Hi, Is this card the same as the T410P, after all, it's made by Digium. There's one prior reference on the mailint list[1] but it didn't answer the question. There was also an SS7 status report[2] last June but it's doesn't seem to have lead anywhere either. There was post saying an SS7 release was immenent last September[3], but then silence. Any info anyone would like to

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

We've changed E1 providers and I'm trying to reconfigure an E400P to make it work with the new lines. They're supposedly "standard" EuroISDN lines (in the UK). I'm initially just trying to get a single line up. I have the following in /etc/zaptel.conf: span=1,0,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 loadzone=uk defaultzone=uk The LED on the back

Hello everyone, We have an E400P Card from phoniceq.? There is a DAHDI Driver posted at: http://e400p.phoniceq.com/driver/dahdi-tor2-tormenta3-e1.tgz but, it doesn't work.? The author (martin (or marcin) pycko) says that it isn't finished. I've e-mailed martin, and he stated that he would fix the driver AFTER we order 10 more cards, not before.? I have a difficult time ordering

I am looking to get the info about QSIG support in Asterisk. Does Asterisk have QSIG support? Does Asterisk support QSIG SIP Tunneling or QSIG SIP Interworking? If so, How to configure that? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060503/3cb7f966/attachment.htm

Hi there. Slackware's installer, that I am internationalizing, makes use of ISOLINUX. I want to give instructions to users in other languages than US English, e.g. which code to type to see installation messages in their native language. So my question are: (1) Which character encodings can be used in message.txt and f1.txt through f1O.txt? (2) Is UTF-8 allowed? (3) I'm guessing that

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo