Displaying 20 results from an estimated 2000 matches similar to: "Kernel Version for CAPI AVM Fritz PCI V2 /chan_capi /chan_alsa update to latest version"
2003 May 27
1
Kernel Version for CAPI AVM Fritz PCI V2 / chan_capi / chan_alsa update to latest version..
Hello there
I have a serious issue with the AVM Fritz PCI V2
I have the following setup and the problem is, that the kernel freezes hard after
about 16 hours. The second problem is, that the S-Bus gets jammed as well, so
you can't even use a analog phone! on the NT
Kernel 2.4.21rc2 with ACPI Patch and of course capi
are there any reasons why this configuration should not work?
And the
2004 Sep 21
1
HELP on AVM Fritz with CAPI drivers for SMP RH 9
Hello,
I have been wrestling with installing the CAPI drivers for AVM Fritz in order
to use chan_capi with Asterisk.
I use an SMP machine, RH 9. I have found rpm's for CAPI and AVM drivers
(namely: capi4k-utils-2003.06.16-08.mungo.RH9.i686.rpm and kernel-2.4.20-8-
avmfcpci-03.11.02-08.mungo.RH9.i686.rpm), but I believe that they support only
single processor machines.
I've already
2005 Jul 27
0
echo capi AVM fritz card
Hi All,
I'm running asterisk 1.0.7 on debian sarge, and
hardware-wise an AVM Fritz!PCI Card, together with chan_capi 0.3.5.
The problem is that any inbound/outbound calls on analogue line result in echo on MY end
(the asterisk end). I've played with the echo settings in capi.conf
(mainly turning on echocancel and echosquelch, also tried playing with
rxgain/txgain) to no avail. The only
2006 Jun 29
4
Very bad quality with AVM Fritz!card PCI and chan_capi
Hi everyone,
I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite
happy with it. However, I am experiencing a quality issue with my AVM
Fritz!card PCI which is used with chan_capi. When somebody calls me on
this line he hears a lot of noise and I hear "scratches" and "plops". It
is very annoying. Below is is my /etc/asterisk/capi.conf
I've tried to
2003 May 14
2
AVM Fritz/Capi without suse ?
Hi All,
Has anyone had success with using the AVM Fritz PCI ISDN Card (v2) CAPI
drivers with a distro other than suse? The AVM driver is geared towards
suse, and after trying them with RedHat 9 I've not got very far. The
module compiles but dies when I attempt to modprobe it.
I've googled until I almost lost the will to live! What little
information
I can find seems to refer back to
2005 Oct 10
2
AVM Fritz! + chan_capi + mISDN + PTP
Hello everyone,
I have been using an AVM Fritz! card with chan_capi and mISDN for
quite a while in PTM mode and it was working finely.
Now, I needed more DID/MSN, so I switched to PTP. But now nothing
works anymore :(
I am using Asterisk on Debian Sarge stable and installed Asterisk
along with chan_capi from apt-get. I installed mISDN from the CVS of
isdn4linux.de.
It is :
- Asterisk
2003 Jun 04
2
chan_capi with avm c2 only uses one BRI
hi all
it seems like whatever I do, I can't use more than 1 BRI on my AVM C2 with
chan_capi. Both channels seem to work, but not at the same time. And - yes -
they're connected to different NT boxes :)
Any ideas? kapejod?
--
Roy Sigurd Karlsbakk, Datavaktmester
ProntoTV AS - http://www.pronto.tv/
Tel: +47 9801 3356
Computers are like air conditioners.
They stop working when you open
2003 Jul 17
4
AVM Fritz! to connect LAN with ISDN line?
Hello,
Is it possible to use * as a gateway in the following setup:
LAN (with Windows NT/Linux PCs)
|
Ethernet (IP)
|
Linux PC with * and AVM Fritz! ISDN Adapter
|
ISDN
|
Someone with a analog/digital phone (POTS)
Basically, people sitting on their PCs will wear a headset, and whenever
they want to call someone,
2006 Mar 15
1
AVM C2 chan_capi-cm-0.6.3 Error on Dial
I'm getting a strange error on one of the two controllers on an AVM C2
card under chan_capi-cm-0.6.3.
I have two ISDN controllers defined, both in the same group, both
connections are UK ISDN2e Point to Point:
On the third outbound call (both of the first two calls are handled by
the second controller "ISDN2",) I get this error :
chan_capi.c conf_error 0x2001 PLCI=0x301
2003 Jun 12
0
help! I still can't use more than 1 of the 2 BRIs on my AVM C2 (chan_capi)
hi all
I still can't use both BRIs on the AVM C2 with chan_capi. This is _annoying_
since people have started complaining about the number of available lines.
Have anyone else seen this?
thanks
roy
--
Roy Sigurd Karlsbakk, Datavaktmester
ProntoTV AS - http://www.pronto.tv/
Tel: +47 9801 3356
Computers are like air conditioners.
They stop working when you open Windows.
2005 Oct 06
0
chan_capi configuration with AVM C2 card
Hi;
I've been asked to take a (remote) look at an Asterisk@home system
running asterisk 1.0.9 on Centos 3.5. It's running chan_capi-0.3.5
It has an AVM c2 ISDN card which is plugged into what I believe to be a
couple of BT ISDN2e "System Access" (i.e. point to point) connections.
We've placed a support call to BT to find out how these lines are
actually provisioned, but
2004 Dec 17
1
chan_capi - avm card does not work
Hi,
I added a Fritz!PCI card to my asterisk system which is running on fc2
!.
I installed the avm modules (fcpci) and when i try an capiinit and a
capiinfo then everything seems to be OK (you can see capiinfo and lsmod
at the end of the text) !.
I installed the asterisk chan_capi module and when i start asterisk and
enter the command capi info on the command line i get back:
*CLI> capi info
2005 May 26
2
chan_capi with an AVM C4 connected to 4 BRI-lines in PTP-Mode
Hi!
I'm goining to connect an AVM C4 to 4 BRI-lines in PTP-Mode, all
BRI-lines will have the same number (1234-XX for example).
I don't know if this is possible and I can't test it, because I don't
have these lines yet.
Is anybody out there, running such a configuration? I'm looking for some
example configs. Especially I want to know how it is possible, to let
asterisk
2003 May 01
0
AVM Fritz-PCI v2.0 and Asterisk
Hello all,
I would like to know about the support for this ISDN passive card AVM Fritz-PCI
v2.0 with Asterisk:
1. which drive should I use with Asterisk: isdn4linux or capi4linux from
AVM
(I read some messages on the asterisk-users archives but I didn't find
the answer)
2. if the drive is isdn4linux then HiSAX support (for passive cards) is
enough ?
and the device /dev/ttyI0 (for
2006 Feb 04
3
Routing Calls via chan_capi with AVM FritzCard
Hello asterisk-users,
I recently set up an asterisk server using Debian Sarge. I also added
an ISDN card (AVM FritzCard PCI) to the machine. I built amd installed
a new kernel (2.6.15.1) with modular support for the CAPI stuff and
also integrated the FritzCard driver available from AVM.
capiinfo succeeds in correctly showing the ISDN card.
When talking from one PC to another via SIP, everything
2011 Oct 20
0
problems getting chan_alsa.so to run
Hi!
I am interisted to dial out from the console with chan_alsa. Can
somebody of you help me according this problem?!
I added user the asterisk to "pulse" and "pulse-access", and it didn't
change anything. alsa applications are routed by default to pulse.
cat /etc/asound.conf
pcm.!default {
type pulse
}
ctl.!default {
type pulse
}
What might be the problem?!
2004 Jun 08
0
Echo problems using AVM Fritz!PCI Card
Hi All,
I'm running the latest asterisk CVS code (from experimental), and
hardware-wise an AVM Fritz!PCI Card, together with chan_capi 0.3.3.
The problem is that any inbound/outbound calls result in echo on MY end
(the asterisk end). I've played with the echo settings in capi.conf
(mainly turning on echocancel and echosquelch, also tried playing with
rxgain/txgain) to no avail. The only
2005 Jan 04
3
AVM C2 capi.conf ?
Hi,
i will use an AVM C2 controller with asterisk.
How can i use both card ports ?? On the voip-info.org Wiki is only notice
to:
You will need a section for each controller in /etc/asterisk/capi.conf so
the C2 will have 2 sections.
But how is look like this ?
Only on the first port is asterisk assume connections, but nothing on the
second card port. In the dmesg is only the capidrv-1 shown,
2010 Feb 25
1
AVM Fritz! mISDN with Kernel 2.6.32 - Any experiences?
Hi to all asterisk-users ;)
As some of you may know, Kernel 2.6.32 includes a module for the
infamous Fritz passive ISDN cards in conjunction with mISDN.
I just would like to know if anybody has tried to use a Fritz card as a
BRI adapter for Asterisk with the new module. If so, i would be grateful
for some hints or howtos.
I am willing to try this myself, but i am quite reluctant as i have
2005 Jun 28
1
AVM CAPI INSTALLATION
I use AVM fritz card A1, I have install with instruction of
Voip-info.or, but it don' work.
capiinfo
Number of Controllers : 1
Controller 1:
Manufacturer: AVM GmbH
CAPI Version: 2.0
Manufacturer Version: 3.101-02 (49.18)
Serial Number: 1000001
BChannels: 2
Global Options: 0x00000039
internal controller supported
DTMF supported
Supplementary Services supported
channel allocation