similar to: iax show registry

Greetings everyone, I'm still a newbie, so please indulge me. I have set up an asterisk server on my RH9 boxes for testing. Instead of immediately launching into the hardware aspect of it I decided to go with 2 IAX clients (gnophone) which I placed on 2 other strategic machines within my LAN. Here's my problem, on one of the IAX clients (gnophone) I am able to do the asterisk demo

DOes anyone have any good suggestions as to good SIP or IAX clients for linux? I have set up and am currently testing asterisk in a controlled environment. I have gnophone running on one of my boxes but the gnophone site has been down. So I can't seem to fing the IAX and Ix-devel rpms or the gsm and gsm-devel rpms. So that prevents me from setting up gnophone on another box. I am

Hi guys As usual I am playing around with IAX soft clients. I was wondering with the various IAX clients, IAX client, DIAX, etc how's one park calls, transfer calls, etc since there is no flash key? Is there something I must do in the iax.conf or is it something I must do with the individual clients? Also, is it very difficult to use musiconhold with the IAX software clients? Thanks a

Hi again, I'm attempting to figure out how to transfer calls from an IAX client. I have read and seen on the list where if you put a ,t at the end of the dial portion in the extensions.conf file that you should be able to use the # to park and transfer calls. I have not found this to be the case. I have tried it several different ways and I can't seem to get it to work. Can anyone

Can anyone give me presise instructions on how to compile cdr_mysql.so? When I initially installed asterisk on the system, I didn't have mysql installed. Since then I have installed mysql, created the database and table structure for cdr_mysql and placed the appropriate settings in the cdr_mysql.conf file. However when I do a show modules at the CLI I cannot find cdr_mysql.so.

Does anyone know what the Grandstream Budgetone is going for $$$ in the US? I didn't immediately see pricing on the phones page. AJ

For anybody who didn't know there is an article on asterisk in February's Linux Journal. AJ

We are in the prossess of ordering a ISDN (PRI) line from Verizon. There are a couple of questions on the application that I don't understand. I'm still a newbie here but we're taking the big plunge. If someone could give me some direction here I would be greatly appreciative. The questions on their app that I don't understand are: 1.) The Verizon Co will outpulse 10

In taking a cursory browse at Vonage's site today, I noticed they are now offering a soft phone. Has anyone had any experience using this? And does this possibly open new opportunities for using Vonage with Asterisk? Just thinking outloud on the list, soliciting thoughts and experiences from others. AJ

Are there any self described or otherwise gnophone experts out there? Maybe I'm a stickler for pain but I'm having a lot of gnophone problems and conventional wisdom tells me that they should be able to be figured out. However, after reading all the documentation, reviewing the files, I am left feeling that I am no closer to the answers than when I first began. So if anyone out there

I've been reading all I can in order to try to implement an asterisk setup. In speaking with someone the other day, they advised they thought there was a way to make a SIP or softphone (gnophone) go straight out to the vonage network through asterisk. I already have vonage set up with an ATA 186. What I'm wondering is is there some way that I could direct dial from a softphone

Greetings all, As most of you probably know from my previous questions on the list, I'm still in the newbie category. My question today is pretty brief, as I told you all a few weeks ago I ordered a PRI from Verizon. I understand that there is a "B" channel that comes with this. The question is just what can I use this "B" channel for and how??? Thanks AJ

In speaking to the representative at Verizon, we came to the conclusion that DID numbers were not the correct solution; however we were told by Verizon that they could do something called assign individual numbers to the PRI. What this would in effect do is give us an additional phone number that we would like to route to a specific extension; however unlike the DID number, it would not be

Can anyone explain to me the difference in zaptel.conf and zapata.conf? I'm trying to get a real clear understanding of them but its getting a little murky in places. I will be setting up a PBX running asterisk with 2 T100P cards. I will be bringing a 23 channel PRI into one card and connecting the other card to a Nortell 24 channel FXS channel bank. As I understand it zapata.conf is

I would like to know how to define the s extension when I have an incoming PRI line? Currently I have 5 incoming DID numbers. Four of these DID numbers I have going to specific extensions, the fifth number which is the main number I wish to go to a background sound where callers can hear message, get directory, dial extension, whatever. I see that the way to normally do this would be to

I have an interesting problem now. I use asterisk to connect to both FWD and a sip provider here in sweden. suddenly, (i know my provider upgraded from a unknown SIP proxy to SER) Asterisk crashes when I try to make a call using this provider. FWD still works fine, and I can call directly towards the GW to POTS without any problems. But, as I call using my providers SER, Asterisk crashes.

I am having a really hard time getting gnophone working with asterisk. Gnophone tries to register with my server but there is no response. I can direct incoming calls to gnophone but if gnophone answers them, asterisk does not recognize it. Here is my configuration: iax.conf [jambo] type=user host=dynamic defaultip=136.159.99.100 permit=136.159.99.100 username=jambo secret=fubar

Hello all I just checked out the latest zaptel/zapata/libpri/asterisk/asterisk-addons from the cvs and ran through the entire make procedures. Everything seemed to go fine however now when I attempt to start asterisk, it says ok but it seems to be immediately crashing. The following messages are displayed in my /var/log/asterisk/messages file for the time right around the crash: Dec 29

Hello guys Is there anyway for me to change the sounds that are presented in VoicemailMain? For instance, instead of it saying "mailbox", I would like it to say something like "please enter your mailbox number now". Is there a way for me to do this? I also noticed that when in some of the menus, even if I select one of the announced options it simply repeats the same menu

Hello All When I open up iaxcomm, it registers fine with the asterisk server. If I call into it, iaxcomm will ring; however if I leave iaxcomm sitting idle for awhile (I haven't figured out exactly how long) it seems to miss calls. I can see the calls coming in on the asterisk server but they never ring through on iaxcomm. If I close it and reopen it, it takes calls again fine. I thought I