similar to: TDM10B problem

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

I've been having trouble with a TDM10B that I installed a few days ago. At first I could not modprobe it at all (getting the errors below). I switched the X100P that was also installed (with a Motorola chip) with one with a Tiger-something chip, and then everything starts up okay. However, after a few hours, the FXS port dies (no battery or anything), and if I try to rmmod & modprobe

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

I'm having a problem defining my channels Here is my zapata.conf ----------------------------------------------------------------------------------------------------- ; Zapata telephony interface ; ; Configuration file [channels] ; rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes

So I have an X100P, and a TDM10B both working (at least I think they are). The drivers have been loaded and ztcfg -vv shows no errors in the configuration of two channels. When I run asterisk -vvvc and pick up my phone (plugged into TDM10B), I don't gear a dialtone. in phone.conf, I have [interfaces] mode=dialtone format=slinear ... Shouldn't that produce a dialtone when I pick up the

Hi list, I have a asterisk box with an E400P that was running ok until last week. The machine just stop responding and after a reboot, the module (tor2) doesn't load anymore. anyone could help? regards Eduardo modprobe returns this: asterix:~# modprobe tor2 Zapata Telephony Interface Registered on major 196 Detected Tormenta 2 Quad T1/PRI or E1/PRA at 0xfe121800/0xfe121000 irq 7

i have error in install module of tor2. but it compile good. what happen ? ivr2:/usr/src/zaptel # make clean; make install rm -f torisatool makefw tor2fw.h rm -f zttool rm -f *.o ztcfg tzdriver sethdlc rm -f zonedata.lo tonezone.lo libtonezone.so.1.0 *.lo rm -f gendigits tones.h rm -f libtonezone* rm -f tor2ee rm -f core cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -c -o

Ok. I am confused. I now have conflicting answers to my question: Do you need to use a special phone to use SIP? My setup is X100P and TDM10B. I would like to connect to iConnectHere, which uses SIP. Has anybody done this before (using similar equipment to what I have listed above)? And if it is not possible, could somebody please explain why. I don't understand why this wouldn't

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

Hello there! I've problem with setting up unicall / mfcR2. can't find proper notation for channel, trying unicall/1, unicall/1/1001, unicall/g1, unicall/g1/1000 and still having no luck. klaudia*CLI> !cp call /var/spool/asterisk/outgoing -- Attempting call on Unicall/1001 for application Dial(363) (Retry 1) Mar 25 09:29:34 NOTICE[19920]: channel.c:2429 __ast_request_and_dial:

Have anybody experience with the following error on a linux system. The system is for the rest running perfect without problems. The system was full installed with Suse 9.1 and updated. Following uname is my kernel 2.6.5-7.104-default Greatings Han Suse 9.1 professional AMD Atlhon XP 2200 Asus A7V600-X bios 1005 1Gb memory 400Mhz Geforce MX 4000 64MB 40 GB Harddisk

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page

Hi, Is this card the same as the T410P, after all, it's made by Digium. There's one prior reference on the mailint list[1] but it didn't answer the question. There was also an SS7 status report[2] last June but it's doesn't seem to have lead anywhere either. There was post saying an SS7 release was immenent last September[3], but then silence. Any info anyone would like to

<P>hi everyone,</P> <P>I know this issue has been raised many times before, i think still the problem remains. When a call is made through a Zap channel, whether it is actually made or not (irrespective of whether, engaged, busy, or actually answered), asterisk logs it in CDRs as a call made. This makes it impossible to do an accurate billing. Has anybody found a way to overcome

Hi, We are trying to validate Asterisk as a media gateway PRI <-> SIP with two T400P (8 T1s) per box. The first experience with BOX1 (Compaq, 2.53 GHz, 1 Gb RAM) and just one T400P was encouraging - on the load test with 3 T1s worth of calls we had on average 75% idle CPU. Not so with BOX2 (Dell, single 2.6 GHz Xeon, 1 Gb RAM, 2 T400P) and BOX3 (Dell, dual 2.6 GHz Xeon, 2 Gb RAM, 2 T400P,

I got the devkit tdm400P(tdm10b) + x100p bundle. Where does one buy more ports for the tdm400p? I couldnt find anywhere on digium site or resellers to buy them? -Dan

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Hi all... I did some Google searches and didn't find any info on this so I'm posting it here... if this was recently discussed, I apologize for the duplication -- please point me to the appropriate thread. System Description: Supermicro SuperServer 5015M-MF w/ PDSMi Motherboard Intel Pentium 4 2.8 Ghz CPU 2 GB DDR2 Memory Digium T400P 4 Port T1 Card CentOS 5.1 (Final) Kernel:

Hi, I found E400P quad PRI card quite cheap (749USD): http://www.govarion.com/product_info.php?cPath=1&products_id=2&osCsid=68cdd6e3d08754 in comparison to te410p (approx 1500 USD ) http://www.digium.com/index.php?menu=product_detail&category=hardware&product=TE410P Now newer generation with HW echo canceling emerged (te411p). I'm not sure in what things those two cards