similar to: Voice Modem Support?

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

Hello List! I finally got asterisk with capi working, and its already answering my call as well! :) Now i would like to call a number from my shoft phone (kphone). This is my extentions.conf: --- [general] static=yes writeprotect=no [globals] CONSOLE=Console/dsp ; Console interface for demo IAXINFO=guest ; IAXtel username/password

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

I'm having a problem booting Slackware 10.1 boot CD's as well as an isolinux image of my own. The system is a VIA Epia M10000 and the drive is an AOpen ISU-8424E CD/DVD writer. If I use a Toshiba CD-RW/DVD-ROM Drive SD-R2612 in place of the AOpen DVD writer, the cd boots fine and everything works as expected. What's the best course for further debugging of this problem? The only

On the cheap side, the ITX or even MicroATX machines work great. These are commodity items, so they tend to be far less expensive than custom solutions. Various manufacturers, but we've had very good success with any of the AOpen MicroATX boards and their slimline MicroATX case: Aluminum: http://usa.aopen.com/products/housing/A340-series.htm Steel:

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

I have asterisk loaded and seemingly working with 4 snom 200 phones. I cannot dial in or out using a DIVA isdn card When I dial out i get "not found xxxxxxx" on the handset. When I dial in i see in /var/log/message isdn_net: Incoming call without OAD, assuming '0' isdn_net: call from 0 -> 0 1856 ignored isdn_tty: Incoming call without OAD, assuming '0' isdn_tty:

Hi, I have a problem that I just can't figure out how to solve. I start *, dial it using a ISDN phone over PSTM, to a Hisax card installed in * I get the demo-greeting, listen for a few seconds and hang up. I dial it again, but this time the first second is sound from where the previous call ended, then the greeting starts as it should. Right now I have removed all codecs but codec_gsm.so

Hello, I am new to Asterisk, so RTFM answers welcome too (just include the FM's link :). I'd like to build a simple dialout server based on Asterisk. I installed 0.4.0 from package (a Debian SID machine, "server"). The client is gnophone (a Debian SID machine too, "client"). My modem is a GVC 56k voice modem connected to the server's serial port. I modified

hey guys i got ubuntu 9.04 and i got wine so i can play a few of my games but none seem to work but only one and the only one that works is star wars Jedi knight Jedi out cast all of the games that don't work are here: Max Payne error:no zbuffer formats found star wars battle front 1&2 don't start at all star craft starts but is very slow and lags star wars eaw does not start at all

Hello, I try to use Asterisk with an Eicon-card called "DIVA Server 4BRI-8M PCI" but I don?t get it to work. I?m running on RH8.0. The Eicon-card supports isdn4linux. In the modem.conf file i have put following: ----------- [interfaces] ; By default, incoming calls should come in on the "remote" context context=remote ; Modem Drivers to load driver=i4l ; Type of dialing

Hi, I'm having a hard time configuring a Mustek Powermust 600VA ups to work via USB with nut. I read somewhere that nut works OK via the rs232 cable, but unfortunately I don't have a COM port in my computer. The kernel detects the ups as an Xbox pad :) and loads the xpad module. I tried running /lib/nut/megatec with different /dev/ttySx but it displays megatec protocol UPS was not

Hi guys, I am trying to connect through an asuscom (56000) serial modem in CentOS5, but when tried Kppp tool it sais no device found. I can't see /dev/modem :( What could you suggest in this cases ? Thanks you in advance.

G'day, New to Asterisk alert! I have a Netjet card running on linux 2.4.27 kernel using the HiSax module, and trying to use it for incoming/outgoing calls from *. I've tried playing with modem.conf and extensions.conf every which way I can think of, using samples and whatever I can find off the net, and I get the same message everytime I try to dial in. The complete message is:

I have installed a Billion ISDN card in my Asterisk. Calls between sip and isdn work. The i4l channel has MSN=26. I also put incomingmsn=26,27 in modem.conf. extensions.con: [incoming-isdn] exten => s,1,Dial(SIP/701,20,Ttr) ;will make my extension 701 ring, while exten => 26,1,Dial(SIP/701,20,Ttr) ;will cause an error message in the Cli interface: WARNING[196621]: pbx.c:1814

I would like to add the ability for our users to be able to press "0" whenever reaching someone's voicemail box to re-reroute them to the auto-attendant. Here's a sample extensions.conf: [incoming] include => ciscophones exten => s,1,Wait,1 exten => s,2,Answer exten => s,3,DigitTimeout,5 exten => s,4,ResponseTimeout,15 exten => s,5,BackGround(auto-greeting)

Sorry to barge in on an old thread. I''m having the same trouble as the gent who started this thread. I''ve tried the options described and can''t seem to get the tunnel to pass packets through it. I''m using the Netscreen Remote VPN client (Safenet derivative) on a windows machine, trying to connect to a Netscreen 5xp at the other end. The connection fires

I have installed two 4-port serial cards (http://www.startech.com/ Product/ItemDetail.aspx?productid=PCI4S550&c=US) on a CentOS 4.4 system. The hardware appears to be recognized correctly, as kudzu added 2 entries to /etc/sysconfig/hwconf and lscpi shows both cards (output of lspci -vv for both cards included at the end of this email): # lspci 00:00.0 Host bridge: Intel Corporation

I found a package on www.bioconductor.com that allows me to install using this line: source("http://bioconductor.org/biocLite.R") biocLite("MassSpecWavelet") The prompt showed me the following message: Running biocinstall version 2.1.10 with R version 2.6.2 Your version of R requires version 2.1 of Bioconductor. trying URL

Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway