similar to: two X100P cards and one TDM400P

Hi, I'm no phone guy but I've been having quite a bit of fun messing with Asterisk. I just unwrapped my new Wildcard TDM400P (TDM40B) which is the new 4 port FXS PCI card. It has 4 RJ45 connectors and I'd like to hookup 4 regular phones which are RJ11. If I crip RJ45 connectors to the phone cords do I simple use the center two pins (pins 4 and 5)? Thanks, Randy Smith Tiger

I'm looking to add a single FXO port to my Asterisk box. It looks like my options are a Digium Wildcard X100P off eBay for $6.99, or a Wildcard TDM400P with an FXO Module from Digium for $125. Can anyone explain the tradeoffs (other than the ability to put 4 FXO/FSO modules on the TDM400P). What about RTC for the system - I know the TDM400P provides it. Does the X100P? Thanks!

Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in

I've searched the Wiki and this forum with little success. I have a TDM400P in my server which functions fine. Except it will continue ringing about 3 times after hangup. I.e. it's failing to detect the hangup tone. I was previously running a Sipura 3000 and had the same issue. After researching and some timely assistance I was able to determine the hangup tones applicable to

Hello. I've seen several posts talking about line quality using Digium cards that are sharing IRQs or on machines where X is running but after trying all of those fixes I am still having a problem with line static on outoing calls. BTW, calls that are from one extension to another extension have no static, however, they have occasional clicks and pops. At any rate, I was wondering if

Hi, I'm thinking of purchasing a TDM400P card and was wondering if anyone has experienced any echo issues with phones off these cards connecting to the PSTN via the X100P cards? I have had my fingers burnt with a Voip phone > X100P. Cheers, Taff. --------------------------------- ALL-NEW Yahoo! Messenger - sooooo many all-new ways to express yourself -------------- next part

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

With one IVR payment system, I noticed quite a difference in DTMF transmission between these two cards. The IVR missed nearly all digits from X100P, while receiving digits from TDM fine. Since neither card process or synthesize audio, what can the difference be? (This particular IVR has problem with some regular phone devices, too.) Yuan Liu

I am sure that quite a lot of people would like to have Caller ID working with their X100P and TDM400P cards outside of USA. Judging from previous threads this is just a matter of implementing this support in the software driver! So, I was thinking, if we get together and put few $(USA DOLLARS) into a basket, we could then ask Digium to actually properly implement Caller ID for non USA

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

Hello. All. I am a bit new to asterisk, started from half a month ago. I am setting up a home asterisk server with analog card. I am using asterisk 1.4.27. At the moment, I bought a X100P card and installed it on my computer. I used it to connect my home phone line. For the moment, it works fine when dial in. Soon I noticed when I dial out through it to my mobile, it can't hang up

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi, all. I'm making my first foray into AEL. I'm starting with a simple macro, but I've already encountered an odd behaviour. I'm wondering if someone can shed some insight: Asterisk 1.2.9.1 macro newPlaceCallPSTN { s => { TIMEOUT(absolute)=7200; NoOp(Analog Out List: ${ANALOGOUT}); ChanIsAvail(${ANALOGOUT}); NoOp(Available Out List:

Has anybody managed to get Fedora Core 3 and the zapata drivers working with the TDM400P cards? Everything is going fine until I do modprobe mcfxs Any ideas? It's a straight install of Fedora Core 3. Graeme -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20041129/026e1455/attachment.htm

I would like to hear from anyone good or bad as what their experience has been in recent times with STABILITY of current builds of Asterisk and drivers for TDM400P. The sort of configuration is: 6 incoming POTS lines. ie. 2 TDM400P cards. I am not concerned with: price points, or the advantages or disadvantages of using POTS vs ISDN technology, but simply RELIABILITY & stability of the

Scenario, I got some very good help earlier from Joseph getting me up and started but I have a couple of small problems still. Setup: FC2 Asterisk 1.0 Zaptel 1.0, TMP400P, FXS Port 1 FXO Port 4 Analog dialout line and Analog handset plugged in. Problems: 1. Incoming calls work and the phone rings and can be answered no problems, (although I wouldn't mind being able to adjust the ring but

Hi to all, I have been using Wildcard TDM400P with four fxs modules and it was working fine now I have added another Wildcard TDM400P with four fxs modules . So there are total 8 ports for 8 hard phones. I have modified following configurations In /etc/zaptel.conf loadzone=us defaultzone=us fxoks=1-8 in /etc/asterisk/zapata.conf context=headoffice signalling = fxo_ks

Hello all We have tested for a mounth or two an asterisk PBX using one T1 channel bank with 24 fxs and one TDM400P digium card with 4 FXO modules. This worked with minor problems, the most notorious being some sporadic static noice or failure in the first FXO module on the wildcard. Now we have a client with 12 pstn lines and 48 extensions and we are trying to deploy an Asterisk PBX server

I have put a box together using 2 X100P and 2 TDM400 4port cards. Using the simple setup that Martin posted a few days ago, I have asterisk almost up and running. /etc/zaptel.conf fxsks=1-2 fxoks=3-10 loadzone=nz defaultzone=nz (I have added NZ tone information to zaptel and Asterisk - I'll submit a patch soon). /etc/asterisk/zapata.conf [channels] context=incoming signalling=fxs_ks

Hi all, Years ago, I was pretty sure attempting to use two TDM400p cards in one machine was recommended against by Digium ... probably because the cards couldn't hack it, and/or interrupt problems etc I have seen some posts recently that seem to indicate it is in fact possible these days thanks to some updated firmware perhaps? ..... I just need to have two in the server because the 4 ports