similar to: Zhone + Digium T1 bug (?)

Hey guys, I've had a working Asterisk setup going for a while now, but am having problems with the Zhone Zplex 10b thinking that during ringing, an extension has answered the call when infact it hasn't. This only seems to happen on some of the ports and doesn't appear to be specific to the handset. Does anyone have any suggestions as to how I could go about fixing this (aside from

Mine has been working well, but the only problem is that it doesn't support callerid (from the POTS side). > -----Original Message----- > From: John Schmerold [mailto:john@katy.com] > Sent: Tuesday, 5 August 2003 12:37 PM > To: asterisk-users@lists.digium.com > Subject: Re: [Asterisk-Users] Zhone Zplex 10 units > > Thanks for the Zplex heads up. > > Steven

I notice most things say to open ports 10000-20000 for UDP for SIP, however from time to time this range isn't where Asterisk is opening the ports: We're at xxx.xxx.xxx.xxx port 8542 Answering with capability 0x2(GSM) Answering with capability 0x4(ULAW) Answering with capability 0x8(ALAW) This call has no audio, presumably because port 8542 is firewalled in the iptables on the server.

I've just received a brand new zhone z-plex 10b. At first, I was able to login using the default (admin/zhone), and started exploring with the configuration, trying to set it up to work with the TE410P. Somehow the admin password was changed, but I don't know what it is anymore. So now I'm stuck at the login prompt, and can't get back to the CLI.... Is there a way to reset the

I've asked this question in the IRC Channel, and have had no happiness yet :-( I have incoming lines hooked to asterisk using X100P's. Unfortunately, when we cal forward our lines using the phone company, the line still rings about a half of a time. This is enough to get * to start 'simple switch' and after my 2 second wait, answer the line. Unfortunately, * doesn't see the

I have just make zhone set2default to factory default setting. What do i have to do to make T1 interface zhone match with T100P.

This may be a long shot, but I suppose it can't hurt to ask! I have seen chatter regarding Zhone channel banks amongst the asterisk users primarily. In all of my searching I am guessing that the majority of people using the Zhone's are probably reading this, and with the support that I have seen from Zhone so far this is probably my best bet, I recently picked one up for a project

I'd like to integrate a few peoples cell phones into our asterisk system as we're walking around a data center some days and carrying another cordless phone just doesn't seem to make sense. Forwarding is easy, however once forwarded I want to be able to flash and transfer back to another party / voice mail / etc. How can this be done? As far as I know there's no way to generate

I've got a Zhone 24 port FXS to configure. The configuration is beyond stupid. The people that designed this unit should be chased down and fired. I'm going around in circles frigging with all the options. Does anyone have a config file for this unit that I can use as a starting point? -bill wlloyd@slap.net

We want to test capacity of our MeetMe room. The thing that is distinct about this is that the incoming line is being delivered IAX2 to our server across the net - so Telephone -> VoIP Gateway -> MeetMe. We want to test both the VoIP Gateway and the MeetMe room performance. You can reach our MeetMe room directly at 1-301-561-9229 If you want to test with us we're thinking maybe 9pm

Hi. I was wondering if the zplex in the dev kit could be configured to have all fxs ports, instead of the standard 8 fxo + 16 fxs. If so, anyone managed to do that? Matteo. -- Matteo Brancaleoni Powered by RedHat Linux 8.0 Linux User #153521 -----BEGIN GEEK CODE BLOCK----- Version: 3.12 GS d? s:- a- C+++ UL++++ P+ L+++ E- W+++ N++ o K- w-- O- M-- V-- PS PE- Y PGP++ t 5 X+ R tv- b++ DI D+ G e

Modem connect speeds on calls through * seem to be lower than calls made through the telephone company lines or our old Rolm PBX. All data calls have 2 wire analog modems on both ends. For my set up I have channels of a Zhone channel bank tied to 2 modems. The Zhone channel bank interfaces my * server with a T400P card. modem --- Zhone Channel bank - * via T400P card - Zhone channel bank -

Everyone - thought I would pass on a useful piece of information. Finally got a solution to my phantom ringing problem. Problem - the zhone is triggered into detecting ringing by the Automatic Line Insulation Tests (ALIT or LIT) run nightly automatically by the telco. Here it is twice between 8pm and 9pm on my particular lines. My first approach before I knew specifically the buzzword for

I've picked up a few Zhone channel banks that I currently am using to test. I've been ready to go into production but I'm a little worried by their behavior. Yes, I've read that they are evil and unsupported by their masters. No, I'm not using the data port. I just need a channel bank. Well, sometimes, when a phone is ringing, * reads that the line picked up even though the

Hi, I have a mint, like-new (used only once) Zhone Z-Plex channel bank for sale. It has 16 FXS and 8 FXO (part number: Z-PLEX-10-24S/O). It functions as a channel bank, router, and CSU/DSU, combining T1, analog voice, and data. D4, SF, and ESF line formats are supported with AMI or B8ZS coding. It has dual T1 jacks, one ethernet jack, one serial port, one V.35 port, and 24 analog pairs

Hi 2 all. I've a nice issue my * system. I have: asterisk latest cvs T100P + Zhone cb (3fxo+10fxs used) Diva Server 4BRI running Capi a bunch of pots and sip phones The whole system is running good (thanks to capigod and Bic. for the help with the Eicon Diva), but there's a very strange issue when calls arrive on the Diva and then bridged to the pots on the channel bank: the voice is not

hello all, I still experience the random off-hook on my fxo cxhannels, i am using a zplex-10b channel bank. which does not allow me to call out. The situation still persists...this is what i have in the zapata.conf [channels] context=internal context=incoming context=default usecallerid=no usecallwaiting=no signalling=fxs_ks channel=1-8 signalling=fxo_ks channel=16-24 but i still have the the

Is there a trick to getting into a zhone z-plex 10 through the serial interface? I tried using a couple of terminal programs the other day and didn't get a login. I have a port that quit working and it doesn't appear to be wiring related. I had another case like this the other day, and after fiddling with the wiring for a long time, I was ready to give up for the night. I restarted

I have been playing with Asterisks for about 6 months, and have fallen in love with it. I have finally taken the plunge and gotten a T100P and a Zhone Zplex-10B (24FXS) channel bank. I have read everything that I can find on the mailing list, checked wiki, even searched the web with google. I believe that most everything is configured right The drivers load without error, and asterisks

Hi I have the last firmware for zplex, if you like i send it to you, about the second question 24s means 24 extensions so you can configurate as you wish as fxo or fxs. Att Yelson Vivas