similar to: regarding the new tdm?0b cards (another newbie question)

hello all i'm interested in setting up a small pbx using asterisk and the primary goal is keeping the cost down. the general layout of the net is as folows: * 4 phone lines (2x isdn+ 2x analog) [or 2x isdn + 1x analog, as one might be put aside for a traditional phone/fax with no fancy stuff] * a server box * several client hosts (all linux with x) currently, the isdn lines are unused (to

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hi Everybody, Has anybody tried the above (or indeed any other 4XBRI cards) successfully with Asterisk. As far as I can see the above mentioned card is an active ISDN card but supported by it's own I4L driver. This leads to interesting questions particularly regarding echo cancellations (which usually doesn't work on the cheap passive cards with one exception as far as I can see).

Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway

Mine is very similar: i don't have echocancelwhenbridged=yes because it seems work only on TDM, is it ? And in Italy, I often have set pridialplan = unknown About echo I have some problems, but only at the beginning of the call. After 3-4 seconds the echo became almost null, specially with snom 190; with pa168s and ywh10 I have again some problem, the echo come up also after 1 minute of

Hallo wine-users, I'm new to wine and to this list. During configuration I got the message that libcapi20 could not be found. I did not worry about that, thinking it was an ISDN thing and I don't use ISDN. But now I have to run a Windows application which insists on using libcapi20 :( I have been searching with Google, but not been able to find any sources for it. Could somebody please

If I want to send outgoing DTMF over a BRI interface, can I do it with 'isdn4linux' or must I use the 'capi' library? -- . . ___. .__ Posix Systems - Sth Africa /| /| / /__ mje@posix.co.za - Mark J Elkins, Cisco CCIE / |/ |ARK \_/ /__ LKINS Tel: +27 12 807 0590 Cell: +27 82 601 0496 -------------- next part -------------- A non-text attachment was

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

I want to test asterisk with its DID functions on a smaller scale without the expense of a PRI. I am in the US, and want the most reliable/stable, and feature rich solution that I can have. What ISDN card would be reccommended? My clec switch operator says he can/will send DID info to my BRI's if I wish. Can Asterisk, or one of its addons support this? What BRI solution would be

Hi list, Does chan_capi work with kernel 2.6? The Eicon Diva server card loads fine judging from /var/log/messages but Asterisk gives an error when trying to load the chan_capi module. I'm using chan_capi-0.3.5, zaptel-1.0.0, libpri-1.0.0 and asterisk-1.0.0 on a Fedora box with kernel 2.6.8-1.584. Zaptel and ilbpri work fine as does *. I have seen a msg that may be related and don't know

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hi, Anybody have lots of experience with PCI ISDN cards and Asterisk? I'm thinking of getting a BRI in my house to deliver more advanced signaling to my PBX (yes, I'm a geek :-)) but I've never played with isdn4linux. Is there any particular BRI card that works better with Asterisk than any other? Also, can the BRI interface cards participate in conference, etc., since they

Hello, I'm having trouble working out how to send DTMF tones to an external IVR. My system has an analog phone connected to a TDM400P card, a SIP software phone (Zultys LIPZ4) and is connected to a BRI in Australia with a NETjet-S card. I'm using ISDN4Linux and a 2.4.25 kernel patched with the ISDN audio patch from Traverse (which allows the card to do voice). DTMF works fine between

I had unexpected hangups from my asterix box using the i4l driver. (SIP <-> SIP calls worked execellent, but SIP<->ISDN didn't.) Then I changed the i4l driver in modem.conf with the chan_capi from jungham. (http://www.junghanns.net/asterisk) I followed his instructions in the INSTALL file, and first encountered some errors compiling it. It help by deinstalling several

Hi, Does anyone use EICON Diva Server Card ISDN and CAPI ? I need some help for drivers installation. I use RED HAT 8.0 (kernel 2.4.18-14) I want to know which drivers should I use and how can I install it. Thanks Rattana -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing