similar to: Tormenta ISA E1 card

Hello,every one! I want to fabric a piece of Tormenta ISA E1 card for study. But the from http://www.zapatatelephony.org is all about Tormenta ISA T1 card. I want to know if they are using the same chips or something different bettween them. Thanks. john

Hello, I had two quad-E1 Tormenta2 cards in my system and yesterday i had to replace the CPU. I noticed the rotary switch on each card that sets the card number or ID... Both switches were set up on 0 and everything worked fine. Should i set one card to 0 and the other one to 1, or... "if it works, don't fix it!" ? I had some nightmares with IDs on Dialogic hardware with Bayonne

Hello: I have a "Tormenta ISA Card, Rev. A" and wanted to know if somebody knows like integrating it with Asterisk. It would thank for any information on the matter. Thanks!!!! -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040907/df5cccd6/attachment.htm

Hi all.. I`m with a problem in some E1 cards. The value of Bipolar Viol is too big, and some times the link seems well, but isn`t work correctly, like as if the link is down. Normally, I use to stop asterisk, remove the modules from my card, use modprove to set up they again, and start asterisk, and it come to work, but in some times I have to reboot the server, and then the value of

Hi there, my * has no Zaptel or Tormenta hardware at all, also no ztdummy. However dmesg is full of Zapata Telephony Interface Registered on major 196 No ISA tormenta card found at d0000 Zapata Telephony Interface Unloaded and /var/log/messages shows tons of this: Nov 25 21:28:28 localhost kernel: Zapata Telephony Interface Registered on major 196 Nov 25 21:28:28 localhost kernel: No ISA

Hi,I want to install the asterisk to my Flash disk without source code. I wonder if somebody could hint me the files that I needed. john

Hi All, I'm having a bit of a time getting my Tormenta 2 card to actually be seen by the system. Whenever I modprobe, the kernel spits out the following (in addition to the "insmod tor2 failed" messages): Invalid Xilinx 8 bit Base resource Registered Tormenta2 PCI Of course, the module says that its registered a Tormenta2 card, but it unloads the driver and frees related

My Esteemed Gurus! Still learning... I need to read about and learn how to configure Asterisk box here in the lab for digital cards. I'm about to get one of those E1/T1 interface cards from Digium. Please point me to docs that I can read so I don't have to bug you with too many questions :-). Sample config files would greatly help. In particular, suppose I have a T1 card in my box

Hi, I have Sangoma A101DE 1 Port E1/T1 With Hardware Echo Cancellation ( PCI Express ) Card installed on the box. *Its not detected.* Details are as below :- [root at asterisk ~]# lspci 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01) 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:05.0 PCI bridge: ATI

Dear all, I have to install an E1 card in my Asterisk 1.4.23 server and here is my short question: Is it necessary to install or update any Asterisk/Zaptel/Any extra module or the default installation is good enough to just plug and run the E1 card ???? Thanks a lot Alejandro

Hi, I have Sangoma A101DE 1 Port E1/T1 With Hardware Echo Cancellation ( PCI Express ) Card installed on the box. *Its not detected.* Details are as below :- [root at asterisk ~]# lspci 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01) 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:05.0 PCI bridge: ATI

Hello list, (Resending this email due to a typo in previous copy) I need to do E1 to T1 conversion for a project, and was wondering if there exists a card with both E1 and T1 on it. Or is it possible to use two separate cards in an asterisk box, one for E1 and one for T1? (Please don't mention aculab or adtran, dealt with them in the past, won't deal again.) I talked to Digium and the

Hello, I just wanted to know if any of you has successfully (or know about) installed the Dialogic 4xFXs ISA CARD D/41 ESC? Does it work with *?, if so, how is the driver called? Thanks a lot for your comments. Alejandro Acosta,-

Does anyone know if I could use modprobe command to find out rather than set the jumper on a Digium PRI card? I want to find out the jumper settings on the card without opening the box which will cause down time. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

Dear all I have asterisk 1.2 and now i want to install E1 card with support Q.SIG singaling so which E1 card is best for my setup i need single port E1/PRI card which support Q.SIG Regards Satish patel --------------------------------- Take the Internet to Go: Yahoo!Go puts the Internet in your pocket: mail, news, photos & more. -------------- next

Hi, I'm having problems with setting up my ISA LineJack card on Linux machine... I've done everithing according to documentation available, by compiling the new ixj driver (v1.2.1), loading it, adding device node /dev/phone0 with major number 100 and minor number 0, adding aliases into the /etc/modules.conf: alias char-major-100 phonedev alias char-major-100-0 ixj and running depmod

> The documentation mentions that the Digium channels can be split into some > voice channels and the remainder of the channels used for routing IP > traffic. > > Does any one have this in use in conjunction with Asterisk? Does it work > well? Would you recommend it for a production server? > > Obviously, if this works, this makes for a cost effective platform where

Dear all I have setup with mediant 2000 with avaya now i want to install E1/PRI card with asterisk and trunk with E1 with Avaya E1 port so i want to buy E1 card for asterisk so which card is best and cast effective for my setup i want 1 port E1 card so can you suggest me which card is best for my setup and i want QSIG singaling with avaya Regards satish patel

Hi All, I am installing a Zaptel Quad E1 card with ISDN PRI in Brazil and I?m with this problem: Asterisk CLI : Mar 27 01:49:57 WARNING[2612]: chan_zap.c:7143 zt_pri_error: PRI: !! No channel map, no channel, and no ds1? W hat am I supposed to identify? Mar 27 01:49:57 WARNING[2612]: chan_zap.c:7143 zt_pri_error: PRI: !! Unable to add IE 'Channel Identification' == Restart