similar to: network prob on Centos 4.4/HP DL320 G2

Is anyone successfully running asterisk on an HP proliant while using their management software, hpasm? I have two DL360's and two TE220B's. The cards have their own IRQ's. No matter what combination of settings I use, the cards fail the patlooptest if hpasm (ver 7.9.1) is running. If I stop it the cards pass the test. I really want to run the management software, so I'd

I am trying to install on a DL320 proliant. The disk is not being recognized. It fails when setting up disk with "no devices" found. I dont get an sda or cciss either one. I tried to disable the on board smart array controller? That didnt seem to make a difference. Is there something special I need to do? Thanks, jerry

I have one HP Proliant DL320 G5p, where for some reason, the AHCI mode is not enabled. According to server specs, it should have AHCI/NCQ capability, but ata_piix module gets loaded during bootup, not ahci module. Any ideas how to enable AHCI mode? lspci output: # lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation

Hi, I have a new server HP proliant DL320 G4, with two 160 GB SATA hdds.. I have installed CentOS 4.5 with mdadm without any problem, but when I disconnect one disk the server does not boot or I received a kernel panic when booting... I have disabled the SATA embeded raid (BIOS) and nothing.. I've also download the driver from HP site HP (Embedded SATA RAID Controller Driver Diskette for Red

Hi Does anyone have experience of running CentOS on HP hardware, both rack mount kit and blades? How are things like hardware monitoring etc? We may be moving from Dell to HP and i get on really well with OMSA and Nagios etc so ideally would like to monitor using similar tools rather than some central 'enterprise' dashboard etc. Any real world experience? thanks

Hi list!: A question about the refinement of the configuration: Always when I start a domain kudzu (hardware detection daemon) ask me for remove hardware. I answer yes, but in the next boot kudzu ask again. I''m guessing that kudzu is asking for remove the «real» drivers that are inside the domU because the domainU was created copying the dom0 system in the domU. How can I deal with

Hi, I have a wireless network but no wired network. I need to access the net for the necessary installation of the wireless drivers in CentOS 5.1. Could anyone let me know how i can go about it!! My card is Intel PRO/Wireless 3945 -------------- next part -------------- An HTML attachment was scrubbed... URL:

Me again. The ASUS P5N32-SLI motherboard in my new machine has dual NICs but CentOS has only detected one of them. I've tried rebooting with the network plugged in only to the second one, but kudzu still doesn't find it. Any suggestions?

What is happening in centos 5 with network config files??? I have a machine with 2 network cards. ifcfg-eth1 keeps changing to DHCP. All my static setup is gone. Why is it doing this? How can I stop it? I run "netconfig -d eth1" and re-setup my static information. I reboot and now I am back to DHCP. I have a gigabyte motherboard, nvidia chipset. forcedeth driver. eth0 is e1000.

Hi gang! At work I have a DL320 G2 machine I use as my desktop (I know, weird!...). Back when I ran RHEL WS 2.1 on it, it always ran a SMP kernel because it has a HypterThread capable processor. When I installed (fresh from scratch) Centos 4.4 on it a while back, though, Centos installed only the UP kernel. I've looked in the BIOS for settings to enable/disable HT support and I don't

I am new to CentOS (coming from Fedora) and I really like it! I am having difficulty getting one of my machines to boot and assign the same designation of eth0 and eth1 to the same nics consistantly. I have an MSI motherboard with 2 nics on the board. Strangely enough both nics report the same MAC address. This is not an issue since I use the computer to route between two different subnets so

I have not see this before... Installing centos 5 on m2n-mx motherboard the onboard forcedeth driver loads and says invalid mac address "97:42:40:F3:18:00" Anyone else ever seen this before? Is it fixable? I went to support.asus.com and searched for "invalid mac address" they say sorry no data. Jerry

1) I'm actually not building a custom kernel per se, just one from the standard 2.6.11.4 with our configuration. I may be adding a custom driver, but unless I can get the standard kernel to boot,... 2) I have been told that after 2.6.11.4, support for the Infiniband driver is dropped, and we need that. If this is not the case, I would be delighted to know that and proceed accordingly.

I need to install an HP Surestore dlt on a Centos 4 machine and I am at a loss as to how to proceed. Can someone either provide or point me to an online reference on how to proceed to add and configure a SCSI adapter and tape drive. I have read, but not really understood, the man page entry for st. Does kudzu handle this? Regards, Jim I am a digest subscriber so the favour of an

Actually, here is what shows up in the log, regardless of whether the driver is built-in or loaded as a module: Feb 5 10:16:15 sparenode1 sysctl: net.ipv4.conf.default.rp_filter = 1 Feb 5 10:16:15 sparenode1 sysctl: net.ipv4.conf.default.accept_source_route = 0 Feb 5 10:16:15 sparenode1 sysctl: kernel.sysrq = 0 Feb 5 10:16:15 sparenode1 sysctl: kernel.core_uses_pid = 1 Feb 5 10:16:15 sparenode1

I'm running up-to-date CentOS 5 w/ Xen. I'm getting tons (tons = 13787 just yesterday, presumably because I have a monitoring system poll every 5 minutes) of log entries of the following: netsnmp_assert index == tmp failed if-mib/data_access/interface.c:467 _access_interface_entry_save_name() and netsnmp_assert rc == 0 failed if-mib/ifTable/ifTable_data_access.c:209

I have installed two 4-port serial cards (http://www.startech.com/ Product/ItemDetail.aspx?productid=PCI4S550&c=US) on a CentOS 4.4 system. The hardware appears to be recognized correctly, as kudzu added 2 entries to /etc/sysconfig/hwconf and lscpi shows both cards (output of lspci -vv for both cards included at the end of this email): # lspci 00:00.0 Host bridge: Intel Corporation

It seems I can't smarm monitor disks on RAID controllers? I tried on several machines with two different controllers and on all I get this when starting up smartd: Jul 27 14:36:43 c1 smartd[5944]: Opened configuration file /etc/smartd.conf Jul 27 14:36:43 c1 smartd[5944]: Configuration file /etc/smartd.conf parsed. Jul 27 14:36:43 c1 smartd[5944]: Device: /dev/sda, opened Jul 27 14:36:43

Redhat has a 'Hardware Discovery Utility' called Kudzu. When I change cards, kudzu pops up and ask to remove/config the card. Most of the time kudzu has trouble recognizing the Digium Zaptel cards and calls them something wrong, like calling the TDM card a network card. I'm having a devil of a time getting 3 TE410P cards to come up with all green lights. For example one or two cards