search for: zthfc1

Hi all, On an Asterisk/Zaptel 1.4 system, one way to gather diagnostic info is: ~# cat /proc/zaptel/* Span 1: ZTHFC1 "HFC-S PCI A Zaptel Driver card 0 [TE]" (MASTER) AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) Span 2: ZTHFC2 "HFC-S PCI A Zaptel Driver card 1 [TE]" AMI/CCS 4 ZTHFC2/0/1 Clear 5 ZTHFC2/0/2 Clear 6 ZTHFC2/...

...18 ... [ 17.835509] dahdi_transcode: Loaded. [ 17.865454] dahdi_echocan_oslec: Registered echo canceler 'OSLEC' [ 18.851312] dahdi: Registered tone zone 30 (Switzerland) [ 18.851372] vzaphfc: card 0: chan B1: TX FIFO has become empty [ 18.851381] vzaphfc: card 0: chan B1 opened as ZTHFC1/0/1. [ 18.851413] vzaphfc: card 0: chan B1 closed as ZTHFC1/0/1. [ 18.851434] vzaphfc: card 0: chan B2: TX FIFO has become empty [ 18.851440] vzaphfc: card 0: chan B2 opened as ZTHFC1/0/2. [ 18.851455] vzaphfc: card 0: chan B2 closed as ZTHFC1/0/2. [ 18.851476] vzaphfc: card 0: chan D ope...

so here it is, the problem that's been nagging me for the past 2 days: connected a box to my telco's NTBA <-> zap/asterisk. which works: box:/etc/asterisk# cat /proc/zaptel/1 Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 ACTIVATED (F7)" HDB3/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) so then I instructed asterisk to treat this as zap interface: box:/etc/asterisk# egrep -v '(^;|^...

...me in the direction of a solution. Here are hopefully some more clues: # lsmod | grep zap zaphfc 13660 1 vzaphfc 24984 1 zaptel 185956 9 xpp,zaphfc,vzaphfc crc_ccitt 2560 1 zaptel # cat /proc/zaptel/* Span 1: ZTHFC1 "HFC-S PCI A Zaptel Driver card 0 [TE]" (MASTER) AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) Span 2: ZTHFC1 "HFC-S PCI A ISDN card 1 [TE]" AMI/CCS 4 ZTHFC1/0/1 Cle...

...====== Zaptel version: 1.4.7 (incl. firmware and modules). OS: Debian etch. Loaded modules: zaphfc 13660 1 vzaphfc 24984 1 zaptel 185956 9 xpp,zaphfc,vzaphfc crc_ccitt 2560 1 zaptel # cat /proc/zaptel/* Span 1: ZTHFC1 "HFC-S PCI A Zaptel Driver card 0 [TE]" (MASTER) AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) Span 2: ZTHFC1 "HFC-S PCI A ISDN card 1 [TE]" AMI/CCS 4 ZTHFC1/0/1 Cle...

...working fine, but the new version of Asterisk add some nice features. All these PBX are in France with France Telecom lines. When I use the new version after about an hour with Euronumeris lines and almost instantly with Euronum?ris+ line, TE lines goes Deactivated in /proc/zaptel/: Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 DEACTIVATED (F7)" AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) I have tested almost all the possible settings for /etc/zaptel.conf and /etc/asterisk/zapata.conf...

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

...ild-out: 0 db (CSU)/0-133 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02) Channel 03: D-channel (Default) (Slaves: 03) 3 channels configured. ### colin@pbxde:/home/colin/ cat /proc/zaptel/1 Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 ACTIVATED (F7)" AMI/CCS 1 ZTHFC1/0/1 ClearChannel (In use) 2 ZTHFC1/0/2 ClearChannel (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) colin@pbxde:/home/colin/ ### Asterisk zap info: ### pbxde*CLI> zap show channels Chan...

...MHz). The OS is Debian etch running Linux kernel 2.6.18 (-5-k7). I've installed asterisk and asterisk-bristuff 1.2.13~dfsg-2etch2, as well as zaptel and zaptel-source 1.2.11.dfsg-1 to compile the necessary modules. My current configuration is as follows: cat /proc/zaptel/* Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 ACTIVATED (F7)" AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) I think TE mode is fine, since I only need it to connect an outside line. Internally, I plan (h...

...terisk/zapata.conf end----------- Asterisk starts without errors. When asterisk is running, the output of the command `cat /proc/zaptel/1` is the following. If asterisk is stopped then the '(In use)' does not exist. ---------------------------begin------------------------------- Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [NT] layer 1 ACTIVATED (G3)" AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) ---------------------------end--------------------------------- Output from asterisk's CLI ----------...

...m doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 12 for device 00:12.0 zaphfc: CCD/Billion/Asuscom 2BD0 configured at mem 0xc3840000 fifo 0xc2d58000(0x2d58000) IRQ 12 HZ 100 zaphfc: Card 0 configured for TE mode Registered Span 1 ('ZTHFC1') with 3 channels Span ('ZTHFC1') is new master zaphfc: 1 hfc-pci card(s) in this box. Registered Span 2 ('ZTRTC/1') with 0 channels Real Time Clock Driver v1.10e I'm using zaprtc as the gateway is running on a VIA motherboard without USB controller. When I'm doing ztc...

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

...zone=nl loadzone=nl span=1,1,3,ccs,ami bchan=1,2 dchan=3 syslog ------ PCI: Enabling device 00:0f.0 (0000 -> 0003) zaphfc: CCD/Billion/Asuscom 2BD0 configured at mem 0xca8fd000 fifo 0xc6348000(0x6348000) IRQ 11 HZ 100 zaphfc: Card 0 configured for NT mode Registered Span 1 ('ZTHFC1') with 3 channels Span ('ZTHFC1') is new master zaphfc: 1 hfc-pci card(s) in this box. ztcfg -vv --------- SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves:...

...nloaded?) Command failed (status=256): 'dahdi_span_assignments dumpconfig > /etc/dahdi/assigned-spans.conf' at /usr/local/share/perl/5.18.2/Dahdi/Config/Gen/Assignedspans.pm line 40. Here is my dahdi_scan: [1] active=yes alarms=UNCONFIGURED description=HFC-S PCI A ISDN card 0 [TE] name=ZTHFC1 manufacturer=Cologne Chips devicetype=HFC-S PCI-A ISDN location=PCI Bus 01 Slot 10 basechan=1 totchans=3 irq=18 type=digital-TE syncsrc=0 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=AMI framing_opts=CCS coding= framing=CAS dahdi_hardware pci:0000:01:09.0 zaphfc+ 1397:2bd0 HFC-S ISDN BRI...

...ncoming calls don't even ring the handset. I'm using the dahdi driver with the zaphfc kernel module. The hfc-s card is in nt mode. The msn is set at the dect phone/base station for outgoing and incoming calls. Asterisk version: 1.6.2.0~dfsg~beta4-0.7501 /etc/dahdi/system.conf: # Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [NT] layer 1 ACTIVATED (G3)" (MASTER) AMI/CCS span=2,0,0,ccs,ami # termtype: nt bchan=1-2 dchan=3 echocanceller=oslec,1-2 alaw=1-3 # Global data loadzone = de defaultzone = de EOF /etc/asterisk/chan_dahdi.conf: [channels] language=de switchtype=euroisdn prid...