search for: upsset

Since there is apparently no immediate solution to upsstats.cgi not reading the output voltage correctly, I have moved on to trying to use upsset.cgi. To recap the UPS is a CyberPower CyberPower CP1500PFCLCD UPS running on a headless server running Slackware 14.1 with the 3.10.7 kernel. The version of NUT is 2.71 and I am using usbhid-ups for communication with the UPS The problem is that when I run upsset.cgi I first get a prompt for us...

Bill S wrote, On 4/15/2014 11:18 AM: > The problem is that when I run upsset.cgi I first get a prompt for > user name and password. I then enter the same username and password > as I established in upsd.users and it seems to accept it. upsset.cgi doesn't check that user/password is valid, it just tries it when doing a command. I just tested it, it is working fo...

Whenever I try to set a value like battery.charge.low using the Network UPS Tools upsset 2.4.3 cgi script, I get an error: Unexpected response: ERR ACCESS-DENIED I can not start a quick UPS test either. Which credentials are used to logon to the upsset.cgi page? I've tried... the username that I configured in upsd.users the root credentials adding a POSIX account & passwo...

On Jul 31, 2013, at 3:36 AM, Pavel Potcheptsov (EKTOS) wrote: > Does it looks good? I think so - 40.8 volts with a nominal of 36 volts is 13.6 V/cell, which agrees with the 100% charge value. Hopefully the line voltages and frequency make sense for your region. > Another question what does riello experimental driver warning mean? We add that to all new drivers. This driver was written by

...:11 ups.conf -rw------- 1 _ups wheel 2770 Jul 31 16:13 upsd.conf -rw------- 1 _ups wheel 2189 Jul 31 16:13 upsd.users -rw------- 1 _ups wheel 11965 Jul 31 16:14 upsmon.conf -rw-r--r-- 1 _ups wheel 3895 Jul 31 16:08 upssched.conf -rw-r--r-- 1 _ups wheel 1416 Jul 31 16:14 upsset.conf -rwxr-xr-x 1 root daemon 6644 Jul 31 16:08 upsstats-single.html -rwxr-xr-x 1 root daemon 4003 Jul 31 16:08 upsstats.html # ls -la /usr/local/ups/ conf/ etc/ # ls -la /usr/local/ups/etc/ total 48 drwxr-xr-x 2 _ups wheel 512 Jul 31 18:32 . drwxr-xr-x 4 _ups wheel 512 Jul 3...

I'm access nut online via localhost. But I have the following problems. When I click on Statistics I get cannot open /etc/hosts.conf. When I click on settings I get: Error: Can't open upsset.conf to verify security settings. Refusing to start until this is fixed. I have .htaccess in cgi-bin with the following: <Files upsset.cgi> deny from all allow from 127.0.0.1 </Files> In /etc/hosts.conf I have: MONITOR belkin at localhost "Local UPS" Any ideas? Thanks --...

Thank you very much!! I have tried configure downloaded source with # ./configure --with-user=_ups --with-group=_ups --with-statepath=/var/db/nut/ and then build driver and copy again. but this doesn't help (driver pid still in the /var/state/ups). Maybe I must add more arguments to change driver's pid location, but I did next, I changed this argument in openbsd ports: # pkg_delete nut #

...ge" field. Annoying. I was wondering if this shortcoming is due to the nut version I'm using now (2.4.1.-3ubuntu2), due to the Ellipse MAX 600 itself, or possibly due to using the serial connection rather than the USB...? Also, I've tried to set a couple UPS parameters using "upsset.cgi", and I observed the following : - I could change the default "battery.charge.low" parameter from "20" to "30". - But when I tried to change "ups.delay.shutdown" and "ups.delay.start" parameters from their default "0" to &quot...

...nd the html files. > Copy this files to /var/www/localhost/htdocs/nut > (if you want it as www.my.org/nut ) > > > In /usr/share/nut you find the cgi files. Copy this files to > /var/www/localhost/cgi-bin/nut > > In that directory create the .htaccess file > > <Files upsset.cgi> > deny from all > allow from 127.0.0.1 > </Files> > > Now you need this files. > > -------------------------- > /etc/nut/hosts.conf > > MONITOR belkin@localhost "Local UPS" > > --------------------------- > /etc/nut/upsset.conf > &gt...

Hi, I own one a MGE Protection Center 675. You can change the parameter ups.delay.start into your UPS to set the "Interval to wait before (re)starting the load (seconds)" use upsset to change the value. Regards, Ren? Le 2013-12-06 15:14, Angel Tsankov a ?crit : > Hello. > > I am faced with a configuration where the OS (Debian 6.0.8) and the PC > shut down before the UPS (MGE Protection Center 675). Also, the UPS > restores power to attached devices as s...

Hello. I am faced with a configuration where the OS (Debian 6.0.8) and the PC shut down before the UPS (MGE Protection Center 675). Also, the UPS restores power to attached devices as soon as main power is back but the PC does not detect power restorations that occur less than a couple of seconds, say 10, after its power supply has been cut. As a result, if main power comes back within 10

...er the UPS has been > shut down, the UPS will power up the PC but the latter will not start. On Fri, 6 Dec 2013, Rene Garcia wrote: > .... You can change the parameter ups.delay.start into your UPS to set > the "Interval to wait before (re)starting the load (seconds)" > use upsset to change the value. Hi, You could also place a declaration such as ondelay = 60 in file ups.conf. Regards, Roger

...-Wsign-compare -o upsc upsc.o ../common/libcommon.a -lupsclient -lssl -lcrypto /usr/lib64/gcc/x86_64-suse-linux/4.3/../../../../x86_64-suse-linux/bin/ld: cannot find -lupsclient collect2: ld returned 1 exit status make[1]: *** [upsc] Error 1 make[1]: *** Waiting for unfinished jobs.... mv -f .deps/upsset.Tpo .deps/upsset.Po gcc -I../include -I/usr/include -O2 -fmessage-length=0 -Wall -D_FORTIFY_SOURCE=2 -fstack-protector -g -Wall -Wsign-compare -o upsmon upsmon.o ../common/libcommon.a -lupsclient -lssl -lcrypto /usr/lib64/gcc/x86_64-suse-linux/4.3/../../../../x86_64-suse-linux/bin/ld: cannot find...

Hello, Ren?. > You can change the parameter > ups.delay.start into your UPS to set the "Interval to wait before > (re)starting the load (seconds)" > > use upsset to change the value. So far, the ups.delay.start parameter in my MGE Protection Center 675 has always been equal to the driver.parameter.ondelay parameter (which equals the ondelay argument in ups.conf). Furthermore, whenever I have changed the ondelay argument in ups.conf (and restarted NUT) t...

...Options +ExecCGI Order allow,deny Allow from all </Directory> ls -l /etc/nut : -rw-r--r-- 1 root root 1104 2008-07-18 13:25 hosts.conf -rw-r--r-- 1 root root 162 2008-07-17 15:17 upsmon.conf -rw-r--r-- 1 root root 1542 2008-07-24 15:09 upsset.conf -rw-r--r-- 1 root root 1773 2008-07-17 13:58 upsstats.html -rw-r--r-- 1 root root 1867 2008-07-17 13:58 upsstats-single.html vi hosts.conf : MONITOR trust at localhost "trust" vi upsset.conf ### I_HAVE_SECURED_MY_CGI_DIRECTORY ### tail -f /var/log/apache2/error.log [Thu Jul 24...

Not fully true about example configs in docs: man pages for CGI bits have some :) https://github.com/networkupstools/nut/blob/master/docs/man/upsset.conf.txt https://github.com/networkupstools/nut/blob/master/docs/man/upsstats.cgi.txt https://github.com/networkupstools/nut/blob/master/docs/man/hosts.conf.txt etc. Other than that, check permissions - e.g. OTOH if Apache user may read your /etc/nut/hosts.conf (and the /etc/nut directory - may be...

...%{_mandir}/man8/upsrw.8.gz %{_mandir}/man8/upslog.8.gz %{_mandir}/man8/upscmd.8.gz %{_mandir}/man8/upsmon.8.gz %{_mandir}/man8/upssched.8.gz %files cgi %defattr(-,root,root) %dir %attr(755,root,root) %{_sysconfdir}/%{PACKAGE} %config(noreplace) %attr(600,%{nutuser},root) %{_sysconfdir}/%{PACKAGE}/upsset.conf %config(noreplace) %attr(644,root,root) %{_sysconfdir}/%{PACKAGE}/hosts.conf %attr(644,root,root) %{_sysconfdir}/%{PACKAGE}/upsstats.html %attr(644,root,root) %{_sysconfdir}/%{PACKAGE}/upsstats-single.html %{_mandir}/man5/hosts.conf.5.gz %{_mandir}/man5/upsset.conf.5.gz %{_mandir}/man5/upsstat...

...ilib.o ../common/libcommon.a ./.libs/libupsclient.so -lssl -lcrypto -L/usr/lib64 -lXpm -lX11 -ljpeg -lfontconfig -lfreetype -lpng12 -lz -lm -lgd -Wl,--rpath -Wl,/usr/local/ups/lib creating upsimage.cgi gcc -DHAVE_CONFIG_H -I. -I../include -I../include -I/usr/include -O -Wall -Wsign-compare -MT upsset.o -MD -MP -MF .deps/upsset.Tpo -c -o upsset.o upsset.c mv -f .deps/upsset.Tpo .deps/upsset.Po /bin/sh ../libtool --tag=CC --mode=link gcc -I../include -I/usr/include -O -Wall -Wsign-compare -o upsset.cgi upsset.o cgilib.o ../common/libcommon.a libupsclient.la -lssl -lcrypto gcc -I../include...

...235.0 input.voltage.fault: 235.0 input.voltage.nominal: 230 output.voltage: 231.6 ups.delay.shutdown: 30 ups.delay.start: 180 ups.load: 0 ups.productid: 5161 ups.status: OL ups.temperature: 25.0 ups.type: offline / line interactive ups.vendorid: 0665 Unfortunately I cannot configure settings using upsset.cgi, but I can issue some commands (turn off the load, start tests of battery, and so on). The upsstats declares that this model is "not supported". I have no previous experience with UPS' . Can any experienced member of the list give me a little help on this. Can I use any specific...

...ues: > > https://github.com/networkupstools/nut/blob/master/conf/upsstats-single.html.sample > > There is also a template for the table of multiple UPSes, but the mapping between NUT variables and HTML table cells isn't as obvious. Ah, I see - I've noticed that when I browse to upsset.cgi, that there are no Settings reported when I select Settings and click the View button. If I select the Commands function and click View, there are only four available: - Turn off the load and return when power is back - Turn off the load and remain off - Start a battery test - Description u...