search for: udma66

...ome machines for a little while, now and noticed something the other day. I was given this system, and I have only run FreeBSD-STABLE on it. The motherboard is a Supermicro370SWD with an Intel 810 "Whitney" chipset (82810DC100 GMCH + 82801AA ICH). The docs say that there is support for UDMA66, but FreeBSD reports that the drive is being set to UDMA33. I booted in verbose mode, and here are the relevant parts from dmesg. atapci0: <Intel ICH ATA66 controller> port 0xffa0-0xffaf at device 31.1 on pci0 ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xffa0 ata0: mask=03 ostat0=50 ostat2...

...for my hard drives during the probe of the CDROM. It just sits there, seemingly forever, though I have never waited longer then a few minutes. The system is a SuperMicro C25BX mother board. The DVD is PATA, reported on boot of 8-Stable as: acd0: DVDR <ATAPI DVD A DH20A4P/9P59> at ata2-master UDMA66 If I unplug the CDROM, it boots fine, but I really need the device on the system, so I really can't leave it unplugged. Also, after the 9 kernel is installed, my Mk file have been updated so that I can't build some ports if I boot the 8.2 kernel. Does anyone remember this being reported by...

...ration. All I get is: --8<-- ISOLINUX 1.75 2002-06-14 isolinux: loading spec packet failed, trying to wing it... isolinux: extremly broken bios detected, last ditch attempt with drive=9F isolinux: disk error 80, ax=432E, drive 9F --8<-- My configuration is: VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:07.1 CMD649: IDE controller on PCI bus 00 dev 48 hda: TOSHIBA DVD-ROM SD-M1502, ATAPI CD/DVD-ROM drive hdc: SAMSUNG CD-R/RW SW-216B Q001 20010913, ATAPI CD/DVD-ROM drive hde: ST380021A, ATA DISK drive CMD649 is an external IDE controller, that has hard drive connected to it (it...

Hi, I am using an ASUS CUV4X-E mother board with a scsi adapter Adaptec AIC-7881U, with one QUANTUM ATLAS_V_18_WLS and MAXTOR 4K040H2, ATA DISK drive connected with a VIA vt82c686a (rev 22) IDE UDMA66 controller. The instalation from original kernel 2.4.7 was ok, but when I upgrade to kernel 2.4.9-31, almost every day I got an error in many process, including apacha, qmail and many other, all off them refering to some functions in ext3 module. Is there any know problem with this kerne...

...URES ENABLE WCACHE taskqueue timeout - completing request directly ad4: WARNING - SET_MULTI taskqueue timeout - completing request directly ad4: FAILURE - WRITE_DMA timed out LBA=32804495 (The address after LBA is not always the same) This is with ad4 as a Seagate ST320423A on a Promise PDC20262 UDMA66 controller. Any suggestions? Thanks, Peter

...ring this device into udma mode again? dmesg: ... atapci1: <ATI IXP600 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0 ata0: <ATA channel 0> on atapci1 ata0: [ITHREAD] ... acd0: DVDR <PIONEER DVD-RW DVR-111D/1.29> at ata0-master UDMA66 ... uname -a: FreeBSD zealot.ksu.ru 7.1-STABLE FreeBSD 7.1-STABLE #1: Tue Jan 20 05:47:24 MSK 2009 root@zealot.ksu.ru:/usr/obj/usr/src/sys/ZEALOT amd64 grep -A 1 DMA /var/log/messages: Jan 27 22:12:19 zealot kernel: acd0: setting up DMA failed Jan 27 22:12:30 zealot last message repeated 36...

...don't have physical access to the machine for quite a few more hours, but when I do should be able to net-boot into the earlier freebsd stable/9 that I originally installed onto this host, and can try a few more things. - Chris atapci0: <AcerLabs M5229 UDMA66 controller> port 0x10200-0x10207,0x10218-0x1021b,0x10210-0x10217,0x10208-0x1020b,0x10220-0x1022f at device 13.0 on pci0 atapci0: using PIO transfers above 137GB as workaround for 48bit DMA access bug, expect reduced performance ata2: <ATA channel> at channel 0 on atapci0 ata3: <ATA chan...

Hello, Before a couple of days ago I started /usr/local/sbin/cupsd manualy from console. When I press CTRL+C to interrupt a program, the system change runlevel and going to reboot. This was on FreeBSD V5.3, today I installed fresh new 5.4 but the problem is the same. cups-base-1.1.23.0_3 -- Todor Dragnev <todor.dragnev@gmail.com>

...10/100 internal PHY> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl0: Ethernet address: 00:50:da:e2:35:3b pci0: <multimedia, audio> at device 12.0 (no driver attached) pci0: <input device> at device 12.1 (no driver attached) atapci1: <Promise PDC20262 UDMA66 controller> port 0xb000-0xb007,0xb400-0xb403,0xb800-0xb807,0xbc00-0xbc03,0xc000-0xc03f mem 0xe9000000-0xe901ffff irq 5 at device 14.0 on pci0 ata2: <ATA channel 0> on atapci1 ata3: <ATA channel 1> on atapci1 acpi_tz0: <Thermal Zone> on acpi0 fdc0: <floppy drive controller&gt...

Hello, I've got a (P)ATA disk in a special frame. The disk itself supports UDMA-100 (and has an 80-ribbon cable), but the frame isn't compatible with that. By default, FreeBSD negotiates UDMA-100, and the console starts to fill with ICRC errors. In the past, I used a patch to ata-all.c that enabled the following entry in loader.conf to force the disk to UDMA-33, so it worked fine:

...cib2 atapci0: <JMicron JMB368 UDMA133 controller> port 0xdc00-0xdc07,0xd880-0xd883,0xd800-0xd807,0xd480-0xd483,0xd400-0xd40f irq 16 at device 0.0 on pci2 atapci0: [ITHREAD] ata2: <ATA channel 0> on atapci0 ata2: [ITHREAD] acd0: DVDR <HL-DT-STDVD-RAM GH22LP20/1.02> at ata2-master UDMA66 acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 cd0 at ata2 bus 0 target 0 lun 0 cd0: <HL-DT-ST DVD-RAM GH22LP20 1.02> Removable CD-ROM SCSI-0 device cd0: 66.000MB/s transfers cd0: cd present [1 x 2048 byte records] acd0...

Hello, I am having a problem with a new server running FreeBSD 4.9-PRERELEASE. Once every two days or so, it reboots itself.. there is no exact time of the day it reboots.. It rebooted itself at 4:25 PM EDT on 9/25, and 3:05 AM EDT on 9/29 (today). I thought it's the bad memory or some sort, so I've been running memtest today and memtest reports no sign of trouble with the memory...

Hi there, System is FreeBSD 4.9 Stable Had a problem during a portupgrade that when portupgrade did some cleaning a directory could not be deleted because it were not empty. However, it was empty. rm -rf didn't help either. Because I didn't know what to do I decided to boot. At system startup fsck was started which produced the message: unexpected softupdate inconsistency and also that

Thomas, Have spoken to Soren, from my bootlog he believes that the problem is in atapicam causing the system to lock up. He is happy to answer some questions but doesnt have time to delve into atapicam himself. Did you author atapicam, I have seen your name on the sourcecode, can you help me further? Whats next? Thanks Adam. -------------- next part -------------- An embedded message was

...rface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ad0: 39205MB <Maxtor 6E040L0> [79656/16/63] at ata0-master UDMA100 ad1: 19623MB <IC35L020AVER07-0> [39870/16/63] at ata0-slave UDMA100 acd0: DVD-ROM <Pioneer DVD-ROM ATAPIModel DVD-120S> at ata1-master UDMA66 acd1: CD-RW <LITE-ON LTR-52246S> at ata1-slave UDMA33 Mounting root from ufs:/dev/ad0s1a cd0 at ata1 bus 0 target 0 lun 0 cd0: <PIONEER DVD-ROM DVD-120S 1.01> Removable CD-ROM SCSI-0 device cd0: 66.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not presen...

Heya.. Yesterday someone "attacked" by box by connection to several ports.. In other words, a simple portscan.. yet, since my box has "log_in_vain" enabled, so it tries to log everything to /var/log/messages, since the logfile got full and the size went over 100K, it tried to rotate the log to save diskspace. (Apr 16 21:00:00 omikron newsyslog[32137]: logfile turned over due

On Monday 14 March 2005 06:29 pm, Mark Williamson wrote: > > I don''t know if this is the right place to post, but I can''t find any > > info about my problem on the net. > > Yes, this is the right place. > > > title Xen2610 > > kernel /boot/xen.gz dom0_mem=131072 console=vga > > module /boot/vmlinuz-2.6.10-xen0 root=/dev/hde1 ro console=tty0