search for: thomasj

Hello! I discovered, that I'm unable to load ther kernel module under 2.4.28. Before that I had 2.4.26 and tryed to upgrade the kernel to 2.4.28. After restart (reboot - soft restart) I can't load the module. When I go back to 2.4.26 and try to load the module, I'm getting the same problem. Only turning off/on helps. What can I do? It's very annoying because the box is in hosting

Hello, Does asterisk do transcoding when the call goes through the system, codecs are the same but signaling protocol is changed. example: SIP with GSM ---> IAX with GSM What quality destruction happen when I use transcoding? I know this is not a concrete/precise question, but I would like to know how is it in general. What CPU performance is needed for transcoding 30 channels e.g. from

Hello, Where can I find docs/specs about USB FXS device (S100U)? How much does these adapters cost? Thanks in advance, Thomas

Hello, are the gsm codecs in Cisco as53xx or 36xx (gsm, gsmfr) copatible with Asterisk's gsm codec? Thanks in advance, Thomas

Hello! I have an E100P connected to our partner's PBX. They want the following: Called number must have numbering plan/type set as: unknown/unknown and calling number in: ISDN/national. I searched for the config file, but I found only pridialplan option on zaptel.conf. When I set it to unknown, the called number has unknown/unknown, however the calling number has as well. When I set

Hello! I'm looking for TEXT sending over IAX2, more precisely sending text messages between IAX2 softphone and asterisk. Currently I'm trying iaxComm and I was able to send a text message from asterisk to iaxComm (with AGI SEND TEXT). After some searching I got some questions: 1. is it possible to send text messages during a call (established or during ringing)? 2. is it possible to send

Hello! I have a special problem with a zaptel PRI card (E100P) with Asterisk STABLE CVS (zaptel and libpri also from stable branch). I use iaxComm softphone for outgoing calls (ulaw currently). Calls are going out through PRI. After about 5-6 calls, when the 7th call arrives, the voice volume on the called party's side is decreased, so they can't hear much (the caller's volume kept

Hello! I got an interesting task to make with asterisk: pstn--- * ---sip--- * pstn This sounds common till now. What I have to make is: 1.the call is routed through PSTN to asterisk1 (#1) which has ISDN PRI interface(s) - leg1 2.#1 doesn't pick up the call, neither rejects, it just place into state CALL PROGRESS (?) [maybe gives back alerting tone? probably not] 3.#1 notifies that there is

Hello! I use FastAGI very frequently [meaning 30 channels IVR is made in it] and sometimes I find, that there is a message like: Jul 29 09:38:55 VERBOSE[896] logger.c: == Auto fallthrough, channel 'Local/1@route-out-eeae,2' status is 'CHANUNAVAIL' Jul 29 09:38:55 VERBOSE[893] logger.c: > Channel Local/1@route-out-eeae,1 was never answered. Jul 29 09:38:55 VERBOSE[896]

Hi Perhaps omeone might answer this tricky problem. I can do this other ways, but i really want to understand how to solve it using ed. I have one solution using g/re/s/re//txt/ , but I want to understand how or if i can solve it using the ed (.)a command. A script i have parse several files and append text after a specific text is matched. If one file do not have this text, i get a no match

Hello, I tryed out spandsp with libtiff-3.5.7 and with Asterisk from CVS. I tryed to receive a fax on a CAPI channel. Finally I got a file with 8 byte length (/tmp/testfax.tif). How can I do next? Thanks in advance, Thomas ps: what are hardware requirements for sending/receiving faxes? -- creating pipe for PLCI=0x101 msn = 2258589 > sent ALERT_REQ PLCI = 0x101 --