search for: te122

Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current...

I have recently built a single-T1 Asterisk box using an HP DL120G6 with a Digium TE122 card. I was finding that I was getting missed interrupts on the TE122, causing the driver to report that it was increasing latency. It kept doing this until the T1 did not work reliably. I tried my usual procedure of disabling the USB subsystem in the BIOS (or so I thought), but I found that the...

Does anyone know if the TE122 is recognized by any of the 1.2 zaptel drivers? It seems that 1.2.16 knows it not... :) Cheers, j

I have setup a asterisk with freepbx, a TE122 and i have an ISDN. My problem now is that callers are experiencing echo. checked on dmesg i saw this: # dmesg -c dahdi: Disabled echo canceller NLP because of CED rx detected on channel 2 i searched google but found no soolution and i have no idea what that error means. below are other details...

What's the difference between the TE121 and TE122. I read the description on Digium's site and it isn't clear to me. Best regards, -- Guilherme Loch G?es Visite nossa loja virtual: http://www.shopvoip.com.br Not?cias e F?rum sobre VoIP com software livre: http://www.asteriskexperts.com.br -------------- next part -------------- An HTML...

...01:00.1 PIC: Intel Corporation 6700/6702PXH I/OxAPIC Interrupt Controller A (rev 09) 01:00.2 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge B (rev 09) 01:00.3 PIC: Intel Corporation 6700PXH I/OxAPIC Interrupt Controller B (rev 09) 03:02.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span T1/E1/J1 card (rev 11) 04:00.0 RAID bus controller: 3ware Inc 9650SE SATA-II RAID (rev 01) 05:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) 06:08.0 Ethernet controller: Digium, Inc. Wildcard AEX800 8-port analog card (PCI-Express) (rev 11) 0...

lspci | grep Digium 03:05.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span T1/E1/J1 card (rev 11) dahdi_scan So I have a card in a box - lspci shows it... dahdi_scan reports nothing. Is my card dead? Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/201611...

...have got a new PRI card at one of our Office locations and now I need to install the the device on a remote server. Is there any way to know if the device is loaded already. When I give " cat /proc/zaptel/* " it returns the following. # cat /proc/zaptel/* Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED IRQ misses: 2 1 WCT1/0/1 Clear (In use) RED 2 WCT1/0/2 Clear (In use) RED 3 WCT1/0/3 Clear (In use) RED 4 WCT1/0/4 Clear (In use) RED 5 WCT1/0/5 Clear (In use) RED 6 WCT1/0/6 Clear...

I am trying to get a zaptel install converted to dahdi. I can get dahdi installed, and the pseudo device even shows up; however, dahdi show channels shows me nothing. There is a TE122 and a TDM800 in there, and neither show up. dahdi show status shows both cards, and dahdi tools show that the cards are there, working, and have no alarms. What am I missing? Michael Munger, dCAP, MCPS, MCNPS, MBSS High Powered Help, Inc. Microsoft Certified Professional Microsoft Certified Sma...

Just wondering how your experience is with HPEC, Is it just for analog interfaces or we can use it on TE122 as well? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080214/3f0580f1/attachment.htm

...eived on my PRI spans. This seems similar to bug 15498: https://issues.asterisk.org/view.php?id=15498 Which says this was fixed in 2.2...so maybe it got back into 2.4? I can get rid of the errors by disabling the mg2 echo canceler in /etc/dadhi/system.conf. The PRI card I'm using is a Digium TE122. I'd prefer not having to run with the echo canceler off of course... [1] active=yes alarms=OK description=Wildcard TE122 Card 0 name=WCT1/0 manufacturer=Digium devicetype=Wildcard TE122 location=PCI Bus 03 Slot 03 basechan=1 totchans=24 irq=35 type=digital-T1 syncsrc=1 lbo=0 db (CSU)/0-133 fe...

Does anyone know if I could use modprobe command to find out rather than set the jumper on a Digium PRI card? I want to find out the jumper settings on the card without opening the box which will cause down time. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, all For some work i'am trying to connect to Asterisk's PBX using isdn cards. But I don't know anything about it. So i'll be pleased to get some information about it! Thanks, Best rgrds!!

Dear, I have an Asterisk PBX with two E1 cards: Digium TE122 and Sangoma A101D. Sangoma card has SNMP support but Digium card has not, and also SNMP does't give me ral time information. Within CLI Asterisk I execute "dahdi show channels" but I don't get information about channels usage. What is the best way to have real time monitoring of...

I'm setting up a test server with a Digium TE122 and am getting the following error on the console, spewing as fast as it can. Does anyone have any idea what this error might be? [Oct 19 11:24:53] NOTICE[2076]: chan_dahdi.c:3108 my_handle_dchan_exception: PRI got event: Event 59 (59) on D-channel of span 2

...RI settings so they can work with their switch manufacturer. We are using the bare minimum default settings, but I can imagine that a whole ton of configurable settings exist that I have never played with. Is there a way to dump all of the configurable settings for a PRI? The card is a Digium TE122. Thanks, j

Hello all, OS OpenSuSE 10.3 * ver 1.4.26.2 zaptel ver. 1.12 Digium TE122 I have a request for remote users to be able to dial through the system so that the sales managers can barge/chanspy on the sales force. I have the DISA part working with authentication(rather straight forward) but what I can not figure out is how to enable the supervisors to be able to barge on...

Hi list, After a lot of testing + troubleshooting, I guess I'm observing what I am now calling a regression with zaptel 1.4.10 (is it?) As such I call for peer feedback, before either asking Digium install support or filing a bug. Thanks in advance! System: HP Proliant DL380 G5 with 2x PCI-X + 1x PCIe riser card OS: Centos 5 Kernel: 2.6.18-53.1.14.el5 (also tested under

The Asterisk.org development team has released Zaptel versions 1.2.22.1 and 1.4.7.1. These releases contain one small change and are otherwise the same as 1.2.22 and 1.4.7. The change is to support the new TE122 card from Digium. Thank you for your support!

The Asterisk.org development team has released Zaptel versions 1.2.22.1 and 1.4.7.1. These releases contain one small change and are otherwise the same as 1.2.22 and 1.4.7. The change is to support the new TE122 card from Digium. Thank you for your support!