search for: t1e1overrid

Hi, I have installed an TE110P but forgot to change the jumper settings to E1. I don't have easy physical access to ther server at the moment so I wonder if it will be possible to run it without changing the jumper settings with a configuration like below or will it be impossible to use the card at all before I fix the jumper? I can't try it myself yet since the operator isn't ready

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and restarting dahdi with no luck. The other two cards are working fine. I put a loop plug the ports and same problem. dahdi_scan [9] active=yes alarms=RED/LFA/LMFA description=T4XXP (PCI) Card 2 Span 1 na...

...o install a TE410P this is what happens with compiled zaptel 1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/ this is my zaptel.conf (checked with the provider the values): span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=it defaultzone=it then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says : Sep 30 16:12:40 localhost kernel: Zapata Telephony Interface Registered on major 196 Sep 30 16:12:40 localhost kernel: Found TE4XXP at base address df5ffc00, remapped to f8aa2c00 Sep 30 16:12:40 localhost kernel: TE4XXP version c01a0164, burst ON, slip debug: OFF Sep 3...

...1.2.4, libpri 1.2.2 and zaptel 1.2.3 from gentoo which uses the source distribution. My configuration is very basic. I have hardly changed anything and the configuration has worked well but the jumper on the card is T1 instead of E1 which would be correct. Loading the module with modprobe wcte11xp t1e1override=15 (see earlier post "run with incorrect E1/T1 jumper settings") makes it possible to configure the card for 31 channels instead of 24 but the sound is still gone. I haven't got the PRI to work but that could be due to other reasons since this is the first time I configure a zaptel...

...Allow 'spantype' to be changed before span assignement via sysfs. dahdi: Remove dahdi_span.irq and move dahdi_span.irqmisses into dahdi_device. dahdi: Expose dahdi devices in sysfs. dahdi: Register devices instead of individual spans. wct4xxp: Deprecate 't1e1override' module parameter in favor of 'default_linemode'. wct4xxp: Refactor t4_serial_setup() to remove t4.globalconfig. wct4xxp: Trivial. Use ARRAY_SIZE in free_wc() and __handle_leds(). wct4xxp: Atomically perform some read/modify/write operations wct4xxp: Fix...

...Allow 'spantype' to be changed before span assignement via sysfs. dahdi: Remove dahdi_span.irq and move dahdi_span.irqmisses into dahdi_device. dahdi: Expose dahdi devices in sysfs. dahdi: Register devices instead of individual spans. wct4xxp: Deprecate 't1e1override' module parameter in favor of 'default_linemode'. wct4xxp: Refactor t4_serial_setup() to remove t4.globalconfig. wct4xxp: Trivial. Use ARRAY_SIZE in free_wc() and __handle_leds(). wct4xxp: Atomically perform some read/modify/write operations wct4xxp: Fix...

...eting E1 in ASterisk/PC Back To Back To Cisco E1 AS5300 Use ISDN Signaling, my configutration : softphone --- > ASterisk ---> AS5300 I need your help me to rights configurations Zapata.conf and zaptel.conf FYI iam already load : modpobe zaptel modprobe wct4xxp t1e1override=15 debug=1 and current /etc/zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow span=3,0,0,ccs,hdb3,crc4,yellow span=4,0,0,ccs,hdb3,crc4,yellow current i have problem error message in cisco as5300 after make a call, if used debug isdn q931 in cisco...

I do part time consulting work. I need to setup an asterisk system to allow me to record both inbound and outbound calls to clients. I have one client that is just a PITA. The client has changed their mind three times so far and we are at step one. I have a spare slackware box and a seperate phone line for the consulting work. I have MCI Neighorhood as my carrier. What I need to know is: 1.

Hi, We have got a new PRI card at one of our Office locations and now I need to install the the device on a remote server. Is there any way to know if the device is loaded already. When I give " cat /proc/zaptel/* " it returns the following. # cat /proc/zaptel/* Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED IRQ misses: 2 1 WCT1/0/1