Displaying 20 results from an estimated 41 matches for "scbs".
Did you mean:
cbs
2008 Aug 01
1
reboot sometimes freezes, adaptic scsi card possible problem
...charging
mfi0: 3798 (270874608s/0x0008/0) - Current capacity of the battery is above
threshold
>>>>>>>>>>>HERE<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
ahd0: Selection Timeout on A:10. 0 SCBs aborted
ahd1: Selection Timeout on A:0. 0 SCBs aborted
ahd0: Selection Timeout on A:11. 0 SCBs aborted
ahd1: Selection Timeout on A:1. 0 SCBs aborted
ahd0: Selection Timeout on A:0. 0 SCBs aborted
ahd1: Selection Timeout on A:10. 0 SCBs aborted
ahd0: Selection Timeout on A:1. 0 SCBs aborted
ahd1: S...
2003 Jul 03
1
SCSI backup error
...4 : Length 20
Jul 3 22:55:19 ene /kernel: (sa0:ahc2:0:6:0): Queuing a BDR SCB
Jul 3 22:55:19 ene /kernel: (sa0:ahc2:0:6:0): Bus Device Reset Message Sent
Jul 3 22:55:19 ene /kernel: (sa0:ahc2:0:6:0): no longer in timeout, status = 34b
Jul 3 22:55:19 ene /kernel: ahc2: Bus Device Reset on A:6. 1 SCBs aborted
Jul 3 22:55:19 ene /kernel: (sa0:ahc2:0:6:0): READ POSITION. CDB: 34 1 0 0 0 0 0 0 0 0
Jul 3 22:55:19 ene /kernel: (sa0:ahc2:0:6:0): UNIT ATTENTION asc:29,0
Jul 3 22:55:19 ene /kernel: (sa0:ahc2:0:6:0): Power on, reset, or bus device reset occurred
Jul 3 22:55:19 ene /kernel: (sa0:ahc2...
2006 Feb 08
1
Raid tools for hardware raid?
...build the raid when I
replace the disk.
We're running Adaptec RAID SCSI adapters:
[oracle at sibrsdbs oracle]$ dmesg | grep -i scsi
SCSI subsystem driver Revision: 1.00
(scsi0) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 0/5/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 396 instructions downloaded
(scsi1) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 0/5/1
(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 396 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EIS...
2007 Aug 03
5
Adaptec 39320A woes
...cd aic79xx/
[root at hcnas aic79xx]# ll
total 0
-rw-r--r-- 1 root root 0 Aug 3 13:09 1
-rw-r--r-- 1 root root 0 Aug 3 13:09 2
[root at hcnas aic79xx]# cat 1
Adaptec AIC79xx driver version: 3.0
Adaptec 39320A Ultra320 SCSI adapter
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
Allocated SCBs: 4, SG List Length: 128
Serial EEPROM:
0x17c8 0x17c8 0x17c8 0x17c8 0x17c8 0x17c8 0x17c8 0x17c8
0x17c8 0x17c8 0x17c8 0x17c8 0x17c8 0x17c8 0x17c8 0x17c8
0x09f4 0x0142 0x2807 0x0010 0xffff 0xffff 0xffff 0xffff
0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0x0430 0xb3f3
Target 0 Negotiatio...
2004 May 27
2
Tape drive problems
...Any suggestion?
I am using CentOS 3 [RHEL ES3 without the licenses]
The tape drive is recognized at boot [from dmesg]
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
blk: queue d3e53014, I/O limit 4095Mb (mask 0xffffffff)
(scsi0:A:11): 80.000MB/s transfers (40.000MHz, offset 32, 16bit)
Vendor: EXABYTE Model: VXA-2 Rev: 100E
Type: Sequential-Access ANSI SCSI revision: 02
blk: queue d37a7e14, I/O limit 4095Mb (mask 0xffffffff...
2003 May 13
0
Health monitoring
...:9e
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xd000-0xd0ff mem
0xfeafc000-0xfeafcfff irq 5 at device 5.0 on pci0
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xd800-0xd8ff mem
0xfeaff000-0xfeafffff irq 10 at device 5.1 on pci0
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
fxp1: <Intel 82557/8/9 EtherExpress Pro/100(B) Ethernet> port
0xd400-0xd43f mem 0xfe900000-0xfe9fffff,0xfeafd0...
2004 Feb 24
2
Deleted files
Thought my troubles were fixed, but files disappeared again and reappeared
after a few dozen rsync cycles.
I am mapping a Win2K directory to Linux with Samba. That mounted directory
is then Rsynced to another Linux box on a schedule (Linux to Linux, because
I can't run rsync on the windows machine).
For some unknown reason, several thousand files are periodically (after
several days) deleted
2003 Apr 14
1
em0: watchdog timeout -- resetting
...00baseTX-FDX, auto
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 100baseTX, 100baseT4, auto
ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0xf800-0xf8ff mem
0xfecff000-0xfecfffff irq 16 at device 9.0 on pci0
aic7895: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0xf400-0xf4ff mem
0xfecfe000-0xfecfefff irq 16 at device 9.1 on pci0
aic7895: Ultra Wide Channel B, SCSI Id=7, 32/253 SCBs
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.4.10> mem
0xfecc0000-0xfecdffff irq 17 at device 16.0 on p...
2005 Sep 09
3
SCSI controller setup
I have an IDE based PC running Linux/CentOS4 to which I wish to
attach a scsi dlt. The host controller is an Adaptec AHA3940
something that lspci reports as:
SCSI storage controller: Initio Corporation 360P (rev 02).
I would like to have the system load the driver for this adapter at
boot but I have two problems: 1. I am not sure which driver to use;
and 2. I do not know how to force
2006 Mar 30
1
Issue with Adaptec AIC79XX module and 2.6-xen kernel
...il
Xen Development Team
Unisys
ACPI: PCI Interrupt 0000:03:0d.0[A] -> GSI 49 (level, low) -> IRQ 18
scsi2 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz,
512 SCBs
Vendor: SEAGATE Model: ST373207LW Rev: D702
Type: Direct-Access ANSI SCSI revision: 03
target2:0:0: asynchronous
scsi2:A:0:0: Tagged Queuing enabled. Depth 32
target2:0:0: Beginning Domain Validation
target2:0:0: wide asynchronous
target2:0:0: FAST-160 WIDE...
2007 Dec 27
2
Failure of gvinum after panic
...gabit PHY> on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0x2200-0x22ff mem
0xfebfb000-0xfebfbfff irq 16 at device 6.0 on pci0
ahc0: [GIANT-LOCKED]
aic7895C: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0x2300-0x23ff mem
0xfebfa000-0xfebfafff irq 16 at device 6.1 on pci0
ahc1: [GIANT-LOCKED]
aic7895C: Ultra Wide Channel B, SCSI Id=15, 32/253 SCBs
s3pci0: <S3 graphic card> port 0x3c0-0x3df,0x4ae8 mem
0xf8000000-0xfbffffff irq 9 at device 1...
2003 Dec 01
0
No subject
...found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
(scsi0) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 3/4/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 392 instructions downloaded
(scsi1) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 3/4/1
(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 392 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EIS...
2007 Jul 20
2
Searching an Scsi Controller for CentOS 5
Hello,
does CentOs 5 supports an Adaptec AHA-2940W/2940UW scsi controller
(pci)? Is this controller maybe supported by the aic7xxx driver?
I want to install CentOS 5 on my desktop pc but the currently installed
pci scsi controller for my scanners (drivers: 2x tmscsim, 1x advansys)
are not supported by CentOS. So I am searching for something else.
Thanks in advanced.
regards
Olaf
2004 Jan 14
2
Dell PE600SC with ServerWorks CSB6
Hello!
Has anyone gotten 4.9R to recognize the "ServerWorks CSB6" ATA
controller on a Dell 600SC? How about installing 5.2R on a 600SC? 5.2R
recognizes the said controller, but it corrupts data.
--
eof
2008 May 27
1
SCSI bus reset with Adaptec 29320ALP and Eonstor RAID
...t 10 seconds and then says
ahd0: Recovery Initiated - Card was not paused
followed by a great detail of SCSI status information. Eventually it
says
(da1:ahd0:0:0:0): SCB 255 - timed out
(da1:ahd0:0:0:0): no longer in timeout, status = 24b
ahd0: Issued Channel A Bus Reset. 1 SCBs aborted
(da1:ahd0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da1:ahd0:0:0:0): CAM Status: SCSI Status Error
(da1:ahd0:0:0:0): SCSI Status: Check Condition
(da1:ahd0:0:0:0): UNIT ATTENTION asc:29,0
(da1:ahd0:0:0:0): Power on, reset, or bus device reset occurred
(...
2002 Oct 18
1
Slow transfer file between Windows and Samba PDC (2.2.3a)
...onment:
Intel(R) Pentium(R) III CPU family 1133MHz (Dell) with a Red hat
7.3 OS (Samba 2.2.3a), with 256Mo of RAM,
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.5
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
less than 10 Windows 2000/ME/98 connected
The first problem was the crash of Excel when someone try to open a XLS
file located on the PDC. According to the log file, it's a oplock
problem (I saw posts about it and 2.2.6pre1 version, seems fixed in the
pre2, right?). I've just disabled thos...
2006 May 30
0
Invalid sequencer interrupt with AIC79xx driver and linux-xen kernel
...ment Team
Unisys, Tredyffrin PA
ACPI: PCI Interrupt 0000:03:0d.0[A] -> GSI 49 (level, low) -> IRQ 18
scsi2 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz,
512 SCBs
Vendor: SEAGATE Model: ST373207LW Rev: D702
Type: Direct-Access ANSI SCSI revision: 03
target2:0:0: asynchronous
scsi2:A:0:0: Tagged Queuing enabled. Depth 32
target2:0:0: Beginning Domain Validation
target2:0:0: wide asynchronous
target2:0:0: FAST-160 WIDE...
2004 Nov 10
5
etherbridge bottleneck
I ran some iperf tests today and it looks like the etherbridge
is the limiting factor on throughput. In the beforetime, I saw great
throughput to the VMs; over 800 Mbps. With the bridge, the numbers
are in the 400s somewhere.
Is this the speed I can expect from the bridge?
Is there some tuning I should try, or another way to get more bandwidth
into the VMs?
This is with xen-2.0, 2.4.27-xen0
2004 Feb 17
1
Erratic Trouble rsyncing between windows share and linux
I am trying to rsync between two linux boxes, but one of the linux boxes is
using samba to map a share from a windows SAN onto it's file system. Rsync
quit working properly when I changed the source directory from a local ext3
filesystem to the windows share mapped onto the filesystem. This setup may
be kind of odd, but I need to keep user's data on the SAN and I also need
the linux box to
2003 Apr 23
1
Compaq ML350 hangs very strange
...<thermal zone> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
ahc0: <Adaptec (Compaq OEM) 3960D Ultra160 SCSI adapter> port 0x2400-0x24ff mem 0xf7df0000-0xf7df0fff irq 3 at device 2.0 on pci0
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec (Compaq OEM) 3960D Ultra160 SCSI adapter> port 0x2800-0x28ff mem 0xf7de0000-0xf7de0fff irq 3 at device 2.1 on pci0
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
pci0: <display, VGA> at device 3.0 (no driver attached)
bge0: <Broadcom BCM5702X Gigabit Ethernet...