search for: pw5110

Hi all, I've got a Powerware 5110 UPS that I'm trying to set up with nut in Ubuntu. I've installed nut and configured the first two files: $ cat /etc/nut/nut.conf MODE=standalone $ cat /etc/nut/ups.conf [pw5110] driver = bcmxcp_usb port = auto # port = /dev/bus/usb/002/002 When I try to test this configuration with the following command: $ sudo upsdrvctl start pw5110 Network UPS Tools - UPS driver controller 2.4.1 Network UPS Tools - BCMXCP UPS driver 0.21 (2.4.1) USB communication subdriver 0.17 Can...

Hello, I 'm trying to set up an Eaton PW5110 using nut-2.4.1 in OpenBSD, my ups.conf follows : [myups] driver = bcmxcp_usb port = auto desc = "Eaton PW 5110 (1500VA)" My first attempt to run upsdrvctl ended up complaining about unimplemented usb_clear_halt() in libusb. I patched libusb-0.1.12 with the...

Hi, I have got a Powerware 5110 UPS which has a usb interface on it. I have downloaded and compiled nut-2.0.3-pre2 with the usb drivers enabled on RedHat Enterprise V3 however I have been unable to get nut to connect to the UPS. I have tried executing the driver directly (using bcmxcp_usb -DD -u root /proc/bus/usb/002/002) as well as using upsdrvctl with the port set to auto (am I correct in

Hi, I am wanting to use NUT to connect to an Eaton Powerware 5110 UPS using USB to connect. - I am using NUT 2.0.2 - I have compiled it with USB support - I can see that the UPS is registered as connecting in /var/log/messages eg usb 3-1: USB disconnect, address 3 usb 3-2: new low speed USB device using uhci_hcd and address 4 But I don't know how to progress from here.

I have an FC5 system with a powerware 5110 usb ups. The system seems to find the UPS ------------------------------ [root@b1 src]# lsusb Bus 004 Device 001: ID 0000:0000 Bus 003 Device 002: ID 0592:0002 Powerware Corp. Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 005 Device 001: ID 0000:0000 Bus 001 Device 001: ID 0000:0000 ------------------------------- [root@b1

...0 connected using USB i did an "sudo lsusb -a" before and after i plugged in the powerware usb cable and did a diff on the results of the two which was: -- 322c322 < Port 2: 0000.0100 power --- > Port 2: 0001.0301 C_CONNECT lowspeed power connect -- current ups.conf is: -- [pw5110] driver = bcmxcp_usb port = auto shutdown_delay = 60 desc = "USB ups" -- did some diagnosis: sudo /lib/nut/bcmxcp_usb -DDDDD -a pw5110 Network UPS Tools - BCMXCP UPS driver 0.11 (2.0.5) debug level is '5' Can't open POWERWARE USB device, retrying ... Can'...

...work properly. System: FreeBSD 6.2 but ugen driver needs patching in order to respect given timeout, patch already included in 7.0 (http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/dev/usb/ugen.c.diff?r1=1.109;r2=1.110) maybe it will be backported in future. However I'm unsure whether PW3105 and PW5110 (those two used with bcmxcp_usb driver) will work after this change. -- ~syhpoon -------------- next part -------------- A non-text attachment was scrubbed... Name: patch-drivers-bcmxcp_usb.c Type: application/octet-stream Size: 890 bytes Desc: not available Url : http://lists.alioth.debian.org/p...

...ll explain more about in a seperate email to the dev list), and the 5110 which I just purchased is using the new bcmxcp_usb from 2.0.4 ... which brings me to the point of the post... The upsc output shows a blank serial number, and no battery.runtime at all, see below: [rohbags@dvr drivers]# upsc pw5110@localhost battery.voltage: 13.5 driver.name: bcmxcp_usb driver.parameter.shutdown_delay: 90 driver.version: 2.0.4 driver.version.internal: 0.10 input.frequency: 50.1 input.voltage: 230 output.current: 0.3 output.frequency: 50.1 output.voltage: 230 ups.firmware: 00.50 ups.load: 16.7 ups.model:...

...NUT's list (Eaton Powerware > UPS 1500), and found out it doesn't support telling me battery level or > runtime! :/ I'm avoiding Eaton/Powerware because the lack of usbhid support, the bcmxcp driver doesn't report much, but I have heard that someone is working on it. Also a PW5110 500 (to replace a APC RS 500) runs much warmer than I would like. I'm used to the APC RS line-interactive units and they don't get nearly as hot. Otherwise, the Eaton/MGE UPS's have been great, a 5PX and an Evolution. The 5PX is kind of a cross, it has usbhid support and Powerware...

...age: $ dpkg -l nut ||/ Name Version Description +++-==================-==================-==================================================== ii nut 2.4.3-1.1squeeze1 network UPS tools - core system Here is the ups.conf file: $ sudo cat /etc/nut/ups.conf [pw5110] driver = bcmxcp_usb port = auto Here's what happens when I try to get the driver to talk to the UPS: $ sudo /lib/nut/bcmxcp_usb -DD -a pw5110 Network UPS Tools - BCMXCP UPS driver 0.23 (2.4.3) USB communication subdriver 0.18 0.000000 debug level is '2' 0.008810 device 0...

I wanted to suggest some rating for functionality. I got the UPS available that seemed to have the best possible rating from NUT's list (Eaton Powerware UPS 1500), and found out it doesn't support telling me battery level or runtime! :/ Luke

...ndling of BCMXCP_RETURN_ACCEPTED_PARAMETER_ADJUST bcmxcp: Use defined constants in setvar, and handle BCMXCP_RETURN_ACCEPTED_PARAMETER_ADJUST bcmxcp: Only calculate ups.load if the UPS does not report it directly I have tested my changes on my "POWERWARE UPS 500i", also known as "PW5110". Here is the output from "upsc" : ambient.temperature.high: 221 ambient.temperature.low: 30 battery.charge.low: 11 battery.voltage: 13.5 battery.voltage.low: 10 device.mfr: Eaton device.model: POWERWARE UPS 500i device.part: 103004261-5591 device.serial: device.type: ups driver.name...