search for: proslic

hi guys, i got a TDM400P FXS card an everything is fine except for this when i do modprobe wcfxs , the linux shows 2 TigerJet Network Inc Model 300 128k. i don't know why it is showing 2 of them. or is that what it is? ERROR: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 0 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 0 cshould be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 0 should be 2 Module 2: Not installed ProSLIC on module 3 insane (1) 0 should be 2 Module 3: Not installed /lib/modules/2.4.20-8/misc/wcf...

...elephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1: Installed -- AUTO FXS/DPO ProSLIC on module 2 failed to powerup within 510 ms (0 mV only) -- DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE TDM400P?? Unable to do INITIAL ProSLIC powerup on module 2 ProSLIC on module 2 failed to powerup within 510 ms (0 mV only) -- DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE...

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed ProSLIC on module 3 insane (1) 0 should be 2 Module 3: Not installed /lib/modules/2.4.20-8/mis...

Hi, I am interesting how can I use the capabilities of ProSLIC to measure the following PSTN parameters: - Voltage (V) & Polarity (+-); - Current (A); - Frequency (Hz). Are there any ready for use tools? If there aren't ready for use tools how can I do the above measuring? Best Regards, Miroslav Nachev

...kernel: Module 2: Installed -- AUTO FXO (FCC mode) kernel: Module 3: Installed -- AUTO FXO (FCC mode) kernel: Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) and the next attempt gives me: kernel: Freshmaker version: 73 kernel: Freshmaker passed register test kernel: ProSLIC on module 0, product 0, version 2 kernel: ProSLIC on module 0 seems sane. kernel: ProSLIC on module 0 powered up to -74 volts (c6) in 10 ms kernel: Loop current set to 20mA! kernel: Post-leakage voltage: 48 volts kernel: ProSLIC on module 0 powered up to -75 volts (ca) in 0 ms...

...never detected. With callprogress=no line get answered as soon as it start ringing, regardless if someone really answer the call. Zaptel channels use fxs_ks signalling . Loading wctdm module with debug=1 result in: kernel: Freshmaker version: 73 kernel: Freshmaker passed register test kernel: ProSLIC on module 0, product 3, version 15 kernel: VoiceDAA System: 04 kernel: ISO-Cap is now up, line side: 03 rev 06 kernel: setting FXO tx gain for card=0 to 0 kernel: setting FXO rx gain for card=0 to 0 kernel: DEBUG fxotxgain:0.0 fxorxgain:0.0 kernel: Module 0: Installed -- AUTO FXO (FCC mode) kernel:...

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

...n pci2 Jul 20 00:50:33 boldsoft kernel: FXS Attach for wcfxs0: deviceID : 0xe159 Jul 20 00:50:33 boldsoft kernel: Freshmaker version: 63 Jul 20 00:50:33 boldsoft kernel: Freshmaker passed register test Jul 20 00:50:35 boldsoft kernel: Module 0: Installed -- AUTO FXS Jul 20 00:50:35 boldsoft kernel: ProSLIC sanity check failed Jul 20 00:50:35 boldsoft kernel: Module 1: Not installed Jul 20 00:50:35 boldsoft kernel: ProSLIC sanity check failed Jul 20 00:50:35 boldsoft kernel: Module 2: Not installed Jul 20 00:50:35 boldsoft kernel: ProSLIC sanity check failed Jul 20 00:50:35 boldsoft kernel: Module 3:...

...n pci2 Jul 20 00:50:33 boldsoft kernel: FXS Attach for wcfxs0: deviceID : 0xe159 Jul 20 00:50:33 boldsoft kernel: Freshmaker version: 63 Jul 20 00:50:33 boldsoft kernel: Freshmaker passed register test Jul 20 00:50:35 boldsoft kernel: Module 0: Installed -- AUTO FXS Jul 20 00:50:35 boldsoft kernel: ProSLIC sanity check failed Jul 20 00:50:35 boldsoft kernel: Module 1: Not installed Jul 20 00:50:35 boldsoft kernel: ProSLIC sanity check failed Jul 20 00:50:35 boldsoft kernel: Module 2: Not installed Jul 20 00:50:35 boldsoft kernel: ProSLIC sanity check failed Jul 20 00:50:35 boldsoft kernel: Module 3:...

Hi, I have Wildcard TDM400P with 2 FXS y 2 FXO. After all work fine but now do it: ----- load driver: wctdm y zaptel (zaptel-1.2.1) Module 0: Installed -- AUTO FXS/DPO Unable to do INITIAL ProSLIC powerup on module 1 Unable to do INITIAL ProSLIC powerup on module 1 Module 1: FAILED FXS (FCC) Module 2: Installed -- AUTO FXO (FCC mode) Module 3: Installed -- AUTO FXO (FCC mode) Found a Wildcard TDM: Wildcard TDM400P REV E/F (3 modules) Registered tone zone 0 (United States / North America) -...

...28 14:01:47 voiplab kernel: Freshmaker version: 71 Nov 28 14:01:47 voiplab kernel: Freshmaker passed register test Nov 28 14:01:50 voiplab kernel: Timeout waiting for calibration of module 0 Nov 28 14:01:52 voiplab kernel: Timeout waiting for calibration of module 0 Nov 28 14:01:52 voiplab kernel: Proslic Failed on Second Attempt to Auto Calibrate Nov 28 14:01:53 voiplab kernel: Proslic Failed on Second Attempt to Calibrate Manually. (Try -DNO_CALIBRATION in Makefile) Nov 28 14:01:53 voiplab kernel: Module 0: FAILED FXS (FCC) Nov 28 14:01:54 voiplab kernel: Module 1: Installed -- AUTO FXS/DPO Nov...

...and it stops here 4. ... No disk reserved for RAID use, RAID disable (actually it meant computer disabled, and it stops here) 5. if I come to boot Linux, than it stops somewhere, with or without kernel panic. The most I came was: Excessive leakage detected on module 0:0 volts (00) after 162 ms ProSLIC module failed leakage test. Check for short circuit DC-DC cal has a surprising direct 107 of 0xff! ##### Loop error (ff) ##### ##### Loop error (ff) ##### ##### Loop error (ff) ##### ##### Loop error (ff) ##### ##### Loop error (ff) ##### ##### Loop error (ff) ##### ##### Loop error (ff) ##### !!!!...

...lly well.. :)) The code is provided at the end of this mail. After browsing the 1.2beta1 release I also downloaded the latest bleeding edge cvs and verified that these parts of the code looked exactly like 1.2beta1. There are a few questions I have though: Why do I have to continuously set the ProSLIC register 64 to 6 (active reverse transmission) to get the tones onto the line if I'm onhook? Only doing it once just after reverse polarity ioctl doesn't do the trick... The idea with SETPOLARITY in addition with going OFFHOOK with ZT_HOOK should be the same, right? It works if I take t...

...maker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXO (FCC mode) Module 1: Installed -- AUTO FXO (FCC mode) Boosting ringinger on slot 3 (89V peak) Module 2: Installed -- AUTO FXS/DPO Timeout waiting for calibration of module 3 Timeout waiting for calibration of module 3 Proslic Failed on Second Attempt to Auto Calibrate Proslic Failed on Second Attempt to Calibrate Manually. (Try -DNO_CALIBRATION in Makefile) Module 3: FAILED FXS (FCC) Found a Wildcard TDM: Wildcard TDM400P REV E/F (4 modules) Registered tone zone 0 (United States / North America) Registered tone zone 0 (...

> 3. Supposed I have 2 fxo cards (right now I have one already) and 3 > fxs, and one of the fxo will have two phone (running pararell), is > there any way for * to: > a. It always dial the first fxo, if the fxo is busy or is being used > (have other people conversation), will * be able to switch it to > other fxo? Here's the approximiate the conditions of the phone.

...6 Jun 21 19:06:16 darthvaden kernel: PCI: Found IRQ 9 for device 02:09.0 Jun 21 19:06:16 darthvaden kernel: PCI: Sharing IRQ 9 with 00:1f.5 Jun 21 19:06:16 darthvaden kernel: Freshmaker version: 71 Jun 21 19:06:16 darthvaden kernel: Freshmaker passed register test Jun 21 19:06:16 darthvaden kernel: ProSLIC 3210 version 2 is too old Jun 21 19:06:16 darthvaden kernel: Module 0: Not installed Jun 21 19:06:16 darthvaden kernel: ProSLIC 3210 version 2 is too old Jun 21 19:06:16 darthvaden kernel: Module 1: Not installed Jun 21 19:06:16 darthvaden kernel: Module 2: Installed -- AUTO FXO (FCC mode) Jun 21 1...

...' divert: freeing divert_blk for eth0 Zapata Telephony Interface Registered on major 196 No ISA tormenta card found at d0000 Registered Tormenta2 PCI Freshmaker version: 73 Freshmaker passed register test Module 0: Not installed Module 1: Not installed Module 2: Installed -- AUTO FXO (FCC mode) ProSLIC on module 3 failed to powerup within 510 ms (0 mV only) -- DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE TDM400P?? Unable to do INITIAL ProSLIC powerup on module 3 Unable to do INITIAL ProSLIC powerup on module 3 Module 3: FAILED FXS (FCC) Found a Wildcard TDM: Wildcard TDM400P REV I (1...

...2, portstatus 103, change 0, 12 Mb/s Zapata Telephony Interface Registered on major 196 usb.c: registered new driver wcusb wcusb: wc_detect_device Second exit host/usb-uhci.c: ENXIO 80000400, flags 0, urb f710eec0, burb f79a32c0 wcusb: Error executing control: status=-6 wcusb: Failed to initialize proslic wcusb: Hardware intialization failed. cleanup Wildcard USB FXS Interface driver registered host/usb-uhci.c: ENXIO 80000480, flags 0, urb f79a32c0, burb f79a3540 usbdevfs: USBDEVFS_CONTROL failed dev 4 rqt 128 rq 6 len 535 ret -6 host/usb-uhci.c: ENXIO 80000480, flags 0, urb f79a32c0, burb f79a3540...

Hi everyone, I have a TDM400 configured with 4 FXS ports, each connected to a caller-id analog trunk port on a Nortel system. Outgoing calls work great. But on incoming calls it appears that loop current is getting dropped momentarily about 10 seconds after the call is answered. Since the Nortel system is programmed to recognize this as remote party hangup it is causing all incoming calls to

Hi All I've got an asterisk system, using a couple of Xorcom Astribanks to provide FXS ports. (I'm using the zaptel 1.2 branch, if that matters) I've noticed that the ringing volume is a lot louder than on our old phone system, and people are starting to complain it's too loud. (This is the noise the phone makes when it rings, not the noise in your handset when you ring