search for: predialing

hi, I hope someone can help me:-) we’ve got a freepbx server. there are 2 special extensions (2001, 2002). if someone calls this extensions (or a call is forwarded to these extensions) and these extension hangup (not the caller party), then we’d like to put the calls back into a queue (1000) and wouldn’t like to hangup. I read your description about hangup hooks:

Hi: I am useing asterisk 11.12. I use G722 as preferred codec for my ip-phone. and my PSTN DAHDI use alaw. G722 is great when ip-phone talks to each other. but when ip-phone dialout to PSTN DAHDI, G722 is not great, since it is need to transcode to alaw. so I try to change the codec when dial from SIP to DAHDI. I tried to use IP_CODEC/SIP_CODEC_OUTBOUND at dialplan. but the SIP

Hi people, I have a problem with some extensions. The calls are ended after 31/35 seconds, also, it depends on the number which I call. This is the log, but I've not been able to find something wrong... Any ideas? [Jun 11 15:50:46] DEBUG[26071] app_macro.c: Executed application: ExecIf [Jun 11 15:50:46] VERBOSE[26071] logger.c: -- Executing [s at macro-dialout-trunk:16]

Hi List Implementing screening and routing I have stumbled over this issue: [pbx-router] exten => s,1,NoOp(ROUTER FROM: ${CALLERID(Number)} TO: ${DESTINATION}) same => n,Set(SOURCE=${CHANNEL(name)}) same => n,Set(PAI=${PJSIP_HEADER(read,P-Asserted-Identity)}) same => n,Set(FROM=${CALLERID(Number)}) same => n,Set(TO=${DESTINATION}) same

In the following macro, a call is dialed and control branches according to DIALSTATUS, much like the default std-exten macro. What I'm trying to figure out is how to regain control when the call is answered. ; Standard extension logic [macro-stdexten] ; ${ARG1}=Extension ${ARG2}=Device(s) to ring exten => s,1,NoOp(stdexten ${EXTEN}) exten =>

I have a PRI connected to a traditional PBX using NI-2 and a typical config (further below). When I call from a SIP/IAX phone to an extension on the PBX, only the number makes it through. If I plug that same port on the PBX to a carrier the PBX presents both name and number. Hints or pokes to relevant chapters in documentation? My config is essentially like one found here:

On Wed, Jun 16, 2010 at 4:35 PM, Shina Owolabi <shinacalypse at gmail.com>wrote: > Hi! > I've installed Asterisk 1.4.32 with freepbx-2.6.0 in an attempt to provide > a conference bridge for an existing Avaya PBX. I have no control over the > Avaya system, but I am able to speak with the admin in charge when I need > stuff done. I am running all this in a VirtualBox

Hello, Sometimes the call gets answered for 1 second, but actually the phone has not rang, it?s just the CDR, and asterisk hangup automatically, I cought the log of 1 call like this, I hope you can help me with this. My setup is : <vendor> ----SIP--? <Asterisk> ?----IAX2---? <Asterisk with Dhadi channels> Here: -- Executing [966505103150 at from-internal:1]

hi,all when i send a call to other server use SIP trunk, i got this below, <--- SIP read from 222.46.18.52:5060 ---> SIP/2.0 403 Forbidden what's rong with is? > Asterisk 1.4.21.2, Copyright (C) 1999 - 2008 Digium, Inc. and others. > Created by Mark Spencer <markster at digium.com> > Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for

i have a prablom here, i want to send a call from A to B use sip trunk , the call can sended B,but not work to PSTN. the message from B server. help pls,what's rong? > > <--- SIP read from 192.168.0.176:5060 ---> > INVITE sip:15921256331 at 192.168.0.151 <sip%3A15921256331 at 192.168.0.151>SIP/2.0 > Via: SIP/2.0/UDP 192.168.0.176:5060;branch=z9hG4bK51a51b96;rport

Hello everyone! I've had this problem for a while and cant figure it out. When an outside caller calls an extension on my asterisk system, they do not hear any sort of ringing. Inside extensions calling other extensions do hear ringing. We have 3 other asterisk systems that are configured the same way, but do not have this problem. We think it has something to do with asterisk 1.6. The other

This has been super-helpful, Eric. However, the handleHangupByPeer priorities below are still not run when the peer hangs-up. The last line in the cli when the peer hangs-up is still: Strict RTP learning complete - Locking on source address (Although sometimes there is also: Retransmission timeout reached on transmission) same =>

Hi All, I've been testing reliability with t.38 faxing pass through with * 1.4.21.1, Linksys ATA's 2102 x 2, Sharp UX-B800SE and Cannon ImageClass D880. cannon> <2102 #1> <SIP> <*> <SIP> <2102 #2> <sharp Started out with default settings on all devices, configured Asterisk to handle T.38 pass through, the configuration I believe is solid. I get

Hi list! I have this configuration for sending T38 faxes to my T38 fax termination provider: T38modem --> hylafax --> Asterisk-SIP-Extension --> T38 termination provider --> T.30 termination to PSTN We are experiencing 2 problems with this (if you want configuration files, it won't be a problem, just tell me): 1. T38 termination provider receives faxes at 2400 bpps from our

hello list i have an issue related to outbound calls i can contact all the number except on number given by our provider in trunk the issue just when i configure my trunk in our server but when i configure the trunk directly in x-lite i can contact this number without issue below the cli == Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 -- Executing [0149xxxxxx at

...nctionality on sipura (pick-up phone and go right into context) successfully. It's conceivable you could change the sipura's dial-plan to include a singular "9", which takes you into the incoming context, and then you could... [incoming] 9,1,Dialtone 9,2,.... Of course, predialing (my phones let me dial a number on display, and once I pick up the receiver, they're dialed) would now become a problem, as establishing the connection may cause the first DTMF digit after the 9 to be missed by *, and you'd have to add a pause to all speed-dial (or pre-dial) numbers. If yo...

I just had a user report that they called out to someone on a cell phone this morning, and after a short conversation, the call was dropped/lost. The person on the cell phone says that this is very rare, and would not suspect the dropped/lost call to be on their side. I have looked at the asterisk/full log as thoroughly as I can, and have pasted the lines which seem relevant to that call below.

Hi All, I am trying to connect my asterisk box with freepbx to PSTN. I have purchased x100p FXO card and installed in my asterisk server. My freepbx detected the x100p FXO card and i can see the card specific details in command line. I have configured the following things. 1. OUTBOUND caller id and Dialing rules in Freepbx. 2. INBOUND route When i call to the PSTN number before

thank you for your response below the asterisk -vvvr Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 -- Executing [0176XXXXXX at from-internal:1] Macro("SIP/300-00000192", "user-callerid,LIMIT,EXTERNAL,") in new stack -- Executing [s at macro-user-callerid:1] Set("SIP/300-00000192", "TOUCH_MONITOR=1427481319.470") in new stack --

I am making some assumptions, but assuming the 217.195.xx.xxx is your provider, you are getting this back from them: "Got SIP response 556 "No address found" back from 217.195.xx.xxx:5060" Are you sure that "0033149xxxxxx" is the format the provider is expecting? You might try enabling SIP debug on the 217.195.xx.xx IP and seeing what the INVITE looks like, but