search for: omnipcx

Hi all, I'm new in the forum, and although I have some experience in Asterisk, I've never work with Asterisk FXO, FXS, E1... cards. I have several costumers with ATAs working with my SER. However one of them bought an Alcatel PBX OmniPCX Enterprise and now he wants I give him a E1 interface for interconection with its new PBX. I understand I need a E1-IP gateway which could be Asterisk I think. So the network would look like this: Extensions-----OmniPCX---E1---Asterisk--------IP--------------SER About that, I have a few question...

Greetings list, I've been asked by someone to help them set up a SIP link between an asterisk system and an Alcatel OmniPCX (v6 software). The asterisk bit's fine, but I know nothing about the Alcatel except that it does apparently allow the setup of SIP trunks. Does anyone have experience with the Alcatel unit? Any obvious pitfalls to watch out for? Any suggestions gratefully appreciated. Regards, Chris -- C.M....

Hello, I have connected asterisk box with legacy PBX Alcatel OmniPCX 4400 (and also another * box connected to A4200). These PBXes have function to assign name to extensions and display it on phone. Asterisk box is connected via PRI with euroISDN signalling (also I have tried QSIG). Is it possible to set callerid with name and display it on alcatel digital p...

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

Morning Asterikians, I've just got my nice shiny quadBRI card, and it seems to be working very well - except for one little issue - CallerID. The card is currently connected to an ISDN2e line in P2P mode, and an S0 adapter on our existing alcatel PBX. The S0 connection recieves callerID and displays it correctly - the 2e line doesn't, and BT have said that CLID was enabled on the

Hi everyone I have successfully compiled and installed OH323 support (finally) into my Asterisk. I want to connect the Asterisk server to our Alcatel OmniPCX Office (OXO) PABX, which has an internal H.323 gateway. I have created the correct dialplans in Asterisk and same in OXO. The OXO only supports G711a G711u G729 and G723.1 codecs. When I call from a SIP phone to OXO using my Grandstream 100 handset with PCMA as the first priority codec, I ge...

Hello, I have the following setup: (*)<--->IP<--->Micronet 5012 H.323 box <---> POTS <---> PBX (Alcatel OmniPCX) Grand idea is to use the micronet's POTS interfaces to connect SIP phones to the PBX and to the PSTN. I think i even managed my way in the arcane and cryptic management interface of that appliance, but I am stuck against theese messages: -- Executing Dial("SIP/xlite1-7a03", "H3...

Hi, Is Asterisk "fully QSIG-compliant"? I currently have an Alcatel 4400 connected to Asterisk 1.2 and 1.4. Zaptel versions are 1.2.26 and 1.4.11. I am using switchtype=euroisdn and all works fine. However, it seems that Alcatel's latest firmware has dropped support for euroisdn which is really despicable. So now I need to see if I can migrate to QSIG which is supported by

Hello list, this is the communication between an Aastra 5000 PBX and Asterisk, where the Aastra makes a call to Asterisk. For some reason, Asterisk responds with 401-Unauthorized and I don't know why. Calls go well with Panasonic PBX, Avaya PBX, Alcatel-Lucent PBX but NOT with this Aastra. A1.A1.A1.A1 = IP-address Asterisk PBX AS.AS.AS.AS = IP-address Aastra PBX Aastra PBX makes a call

...g to solve a problem and after unsucessfully chasing forums and google for some hours, I turn to you in hope of a solution. I feel it's just a configuration issue but I just can't get my head wrapped around it. The situation is basically this: I have an Asterisk connected to an Alcatel OmniPCX via SIP. Asterisk only ever does SIP and has no dedicated hardware phone interface. The Alcatel PBX is connected to the public phone net, and is configured to forward all calls to a certain number to Asterisk. Also when Asterisk dials out, that number is correctly transmitted by the PBX. Asteri...

Hi guys, Recentlly i did a asterisk gateway and use it with an alcatel pabx. All is working, i have only two problems. 1. When call incomming to asterisk, it forward to digium card to PABX Alcatel. The user that start the call can't hear the control tone of ring ring ring. Tha calls stay without sound until the called part answer the call. At this point, conversation follow normaly. 2. When

I have a PRI E1 link between Asterisk 1.4.24 and Alcatel-Lucent OmniPCX Enterprise R9.0. As EuroISDN it works fine. However, I need to move to QSIG because of a firmware upgrade on the Alcatel PBX which doesn't support EuroISDN (please don't ask why). Besides, I've read somewhere that 2 B Channel Transfers "should" work with * 1.4, the latest 1...