search for: murino

Hi, I configured some ha services using heartbeat, I have this on my log: Nov 14 09:59:06 mail1 heartbeat[3932]: ERROR: Unable to send bcast [-1] packet: Operation not permitted Nov 14 09:59:06 mail1 heartbeat[3932]: ERROR: write failure on bcast bond1.: Operation not permitted how allow broadcast only on some interfaces with shorewall? attacched is shorewall status Thanks Nicola

I have upgraded to trustix 2.1 (kernel 2.4.25-2trfirewall), there is a problem with shorewall (both 1.4.10d and 2.0) and iptables 1.2.9-2tr when I start shorewall I have the following errror: iptables v.1.2.9: Unknown arg ''--icmp-type'' Try ''iptables -h'' or ''iptables --help'' for more information with trustix 2.0 (kernel 2.4.25-2trfirewall)

Hi, in my lan I have two firewall, fw1 is the first and manage inte-vlan routing. Fw2 manage internet and dmz. fw1 and fw2 have an interface (eth4 for both fw2 and fw1) on the same subnet that permit to the host behind fw1 to reach internet, my problem is on fw2: eth4 is the NIC that connect fw2 and fw1, I would''t like masquerading hosts behind fw1, so to eth4 of fw2 arrive all

[This email is either empty or too large to be displayed at this time]

Hi all, I some vlan routing problem, I''m using a linux box with an 8021q kernel. I have connect eth2 ethernet controller from linux box to a switch port that carry for vlan tagged as 2 3 4 5, I''m able to connect to the internet from vlan but not to route traffic between vlan, this is the output of ifconfig -a: eth0 Link encap:Ethernet HWaddr 00:A0:24:50:E5:B2

Hi, I want to setup an opensource system for voip and traditional pstn calls; I have an adm with 15 outgoing lines that is connected to al alcatel box, I want to try asterisk and connect a linux box with asterisk to the adm instead of alcatel box; I have read some documentation and seems that I must buy a Wildcard T100P ( http://www.digium.com/index.php?menu=wildcard_t100p ). I would like to

Hi list, I have two location connected by a vpn, in each location I have a samba server that is the local master browser. The first subnet is 10.10.10.0/24 and the samba server have 10.10.10.100 ip address, the second subnet have 10.10.11.0/24 and the samba's server ip address is 10.10.11.3. For the server 10.10.10.100 (samba 2.2.8) I have defined the following parameters (this are the

Hi list, I have the following problem: my boss and some other people on my lan want to use their ISP smtp to send mail when they connect from work lan, but, of course, their ISP smtp don''t allow relay when they aren''t at home. You can image my networks so: eth0 internet public ip eth1 local1 10.88.11.0/24 eth2 local2

Hi, I would like to have some more informations on asterisk, I want to setup a linux based pbx and asterisk seems to be the best solution, I have some questions for configuration: 1) I have a PRI, so I must buy a digium card to interface with PRI, right? 2) If I connect an ethernet card from the pc (equipped with a digium card connectd to the PRI) to a switch I can connect users to this

Hi, I have a proxy/firewall, I want to dnat requests for 193.205.140.106 on port 443 towards 10.2.15.23 and requests for 193.205.140.106 on ports 4330 and 3389 towards 10.2.15.25, these rules must apply from internet, loc and fw (some client use a proxy on fw to reach these servers) I have tried with the following rules: DNAT net dmz:10.2.15.23 tcp 443 -

Hi, according to RFC 4253 https://www.rfc-editor.org/rfc/rfc4253#section-7.1 for the selection of algorithms (ciphers, KEX, MAC etc.), the leftmost matching client algorithm is picked. While this is fine in most cases, there are cases where it is not desirable, for example: 1) for compatibility with a single old client you enable an old cipher, say aes128-cbc, server side. A modern client

Hi list, I have a problem with samba 3, with samba 2.2.x I have configured my samba server with a virtual host adding the following configuration: netbios aliases = alias include = /etc/samba/smb.conf.%L and then I have created a configuration file smb.conf.alias, and I have configured it as a separate server, in this way on the same machine I have two server: the first configured by the

Hi all, I'm trying to configure samba as PDC, I have a problem when windows client log in this is the error: Windows cannot load the profile and is logging you on with a temporary profile. Changes you make to this profile will be lost when you log off I have samba-3.0.11 and smbldap-tools-0.8.8. I tryed also samba-3.0.14 and smbldap-tools-0-9.1, I have the same problem on Gentoo and on