search for: mroute

Hi, I have problem with multicast routing on my network. I tried mrouted and also pimd, but always same problem. When I set mrouted or pimd on one router, everything works fine, but when I start mrouted/pimd on another one, routing die. In moment when I start anorher mrouted/pimd /proc/net/ip_mr_cache is cleaned. My topology: g...

Hello I am running smcroute(version 0.9) on Linux 2.2.16-22 and I have configured two multicast (S,G) addresses to forward. The forwarding is working. I get the following message several times per minute. mroute: pending queue full, dropping entries The kernel has the following options CONFIG_IP_MULTICAST=y #CONFIG_IP_ROUTER=n # is this required??? CONFIG_IP_MROUTE=y CONFIG_NET_IPIP=m (module istalled with no difference) Any idea why the kernel is reporting these error messages? Stuart Stevens R&a...

I am trying to set up my Shorewall box to forward multicast packets to my local net. I do have some problems with mrouted (see below), but I can join and add routes using smcroute. Multicast works when shorewall is disabled. I got a lot of help from the following. http://lists.shorewall.net/pipermail/shorewall-users/2005-January/016674.html I cannot get the multicast packets to pass the fw when Shorewall is enabled....

...when i start shorewall the stream is stopped on the windows client. when i start only iptables: the streaming is good then when i start shorewall: the streaming is stopped then when i stop shorewall : the streaming is ever stopped then but when i restart iptables : the streaming is good again the mrouted find the multicast address on the eth1 and forward well on the eth0, same without 1 on /proc/sys/net/ipv4/ip_forward. (when i stop iptables the /proc/sys/net/ipv4/ip_forward is 0 and the mulcicast routing is functional). Thanks for your help VUILLET Damien Network Administrator of a french agricu...

I wouldn't expect you to be using RFC3389 if your using A-law, can you include your IOS version and IOS config file ... I have not specified any allow's or disallow's in my * config for the codecs with my 5300, I also use Cisco 79xx phones and I use the option within the phones config file to select the preffered codec and when I change this to G.729/A-law/U-law all works perfectly

well, once i figured out what to do it was easy. 1) install freebsd over linux. 2) recompile kernel with: option MROUTING 3) start mrouted 4) go get yourself a cold beer. you deserve it! thanks! -bob CONFIDENTIALITY NOTICE: The information in this electronic mail transmission contains confidential information intended only for the use of the individual or entity named above. If the reader of this message is not the intended...

...711ulaw codec preference 2 g711alaw codec preference 3 gsmefr codec preference 4 gsmfr ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! interface Ethernet0/0 ip address xxx.xxx.xxx.yyy 255.255.255.0 no ip route-cache no ip mroute-cache full-duplex no cdp enable ! interface Ethernet0/1 no ip address no ip route-cache no ip mroute-cache shutdown half-duplex no cdp enable ! ip http server no ip http secure-server ip classless ! ! ! ! call rsvp-sync ! voice-port 1/0/0 input gain 10 output attenuation 10 no comfort-no...

Fix one serious bug (in libnetlink), and a couple of other minor patches. http://developer.osdl.org/dev/iproute2/download/iproute2-051007.tar.gz Stephen Hemminger Reenable ip mroute Mike Frysinger Handle pfifo_fast that has no qopt without segfaulting Mads Martin Joergensen Trivial netem ccopts Jerome Borsboom Fix regression in ip addr (libnetlink) handling -- Stephen Hemminger <shemminger@osdl.org> OSDL http://developer.osdl.org/~shemminger

...2.168.2.5 61.11.104.0/24 dev eth0 proto kernel scope link src 61.11.104.63 127.0.0.0/8 dev lo scope link default via 61.11.104.1 dev eth0 [root /root]# ip Usage: ip [ OPTIONS ] OBJECT { COMMAND | help } where OBJECT := { link | addr | route | rule | neigh | tunnel | maddr | mroute | monitor } OPTIONS := { -V[ersion] | -s[tatistics] | -r[esolve] | -f[amily] { inet | inet6 | ipx | dnet | link } | -o[neline] } Thanks and Regards, Pankaj Agarwal _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailm...

...r 224.0.0.0/4 and for a specific multicast group (say 239.16.2.2) to the netB and netC "devices", but the multicast traffic isn''t getting out of its source LAN. Are there ip commands that will do it? Do I need additional software running for multicast? I couldn''t get mrouted or pimd to compile on Fedora Core 4. I installed xorp but haven''t tried running it yet because I''m very confused about what is needed, besides the basic kernel and iproute2, for a multicast-capable Linux router. Thanks.

...15,27 hard ! controller E1 1 clock source line primary pri-group timeslots 1-31 ! controller E1 2 shutdown ! controller E1 3 shutdown pri-group timeslots 1-31 ! gw-accounting h323 gw-accounting h323 vsa gw-accounting voip ! ! interface Ethernet0 no ip address no ip route-cache no ip mroute-cache shutdown ! interface Serial1:15 no ip address isdn switch-type primary-net5 isdn incoming-voice modem isdn T321 40000 isdn T310 4000 isdn negotiate-bchan no cdp enable ! interface Serial3:15 no ip address isdn switch-type primary-net5 no cdp enable ! interface FastEthern...

The BBC are currently trialling multicasting the Olympics. This requires multicast and IGMP to be available. As far as I can make out, in 2.0.8 at least, all multicast addresses are filtered out and, to my naive eyes, can''t be re-enabled. Please prove me wrong :-) Dirk -- Please Note: Some Quantum Physics Theories Suggest That When the Consumer Is Not Directly Observing This Message,

If you have a PRI terminated in a Cisco router talking SIP to * and would be willing to share your Cisco config, please respond. Also, I would be interested in knowing what version of IOS you are using. We are using an NM-HDV in a 3640. TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 236-5815

I have a standard 3 interface shorewall setup and I want to receive multicast stuff from ''net'' -> ''loc''. This requires me, first, to do an IGMP join which involves 192.168.1.x -> 224.0.0.x being NATed out as the ''net'' interface''s IP address. Obviously replies have to be NATed back to ''loc'' addresses. Can

I'm experimenting (using for the first time) with using a cisco3620 to connect to the PSTN via a channelised E1 interface, with * handling all of the SIP calls. If anyone has any installation tips / help / documentation I would be most appreciative :) However, my first question is this: when I am in the setup, I see the following: Current interface summary Controller Timeslots

Hello list, Not sure if I am asking the question in the correct list. I am a newbie trying to get multicast routing to work on my linux 2.4 kernel. I am using usc pimd code. I have pimd which sets up the route in the kernel [ /tmp]# ip mroute show (22.22.22.1, 224.0.1.20) Iif: eth2 Oifs: eth1 [ /tmp]# I can see data packets arriving on eth2 [/tmp]# tethereal -i eth2 Capturing on eth2 0.000000 22.22.22.1 -> 224.0.1.20 UDP Source port: 32770 Destination port: 12345 1.000000 22.22.22.1 -> 224.0.1.20 UDP...

...e traffic is getting dropped at a low level. Question: My question at this point is problem identification. Is the router configured correctly and acting as expected but the client just isn''t sending the IGMP join requests? Do I need to install additional software packages like Zebra or mrouted to make this work? Am I completely missing something? Any help or suggestions are greatly appreciated! regards, -bob -bob CONFIDENTIALITY NOTICE: The information in this electronic mail transmission contains confidential information intended only for the use of the individual or entit...

Hi All, As it is written in the "Linux 2.4 Advanced Routing HOWTO" GRE tunneling has some benefits compare to IP-in-IP, on of it benefits is the ability to transport multicast traffic through a GRE tunnel. I used the mrouted daemon and I know that the daemon supports tunneling but I don''t want to use its tunneling method. Assuming I have gre0 as my tunneling device I did the following: 1. declare the following rules: Ip rul add iif eth0 table 100 prio 100 Ip rul add to 240.0.0.0/4 table 101 prio 101 2. dec...

Hi. I want to drop silently locally generated packets on a specific interface. I tried 2 approaches: tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1: htb tc filter add dev eth0 parent 1: proto ip u32 match ip dst 10.10.10.1 flowid 1:1 police conform-exceed drop/drop tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1: prio bands 2 priomap 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Hi all, We want linux (ubuntu) with 2.6 kernel to act as multicast router and to pass multicast packets between different subnets. And linux machine as router has two network cards having two different subnets assigned onto. We first worked "sysctl -w net.ipv4.ip_forward=1" line on linux shell that made linux to work as unicast router. (like host, the multicast packets were discarded at