search for: lsi53c1030

...ivers should be automatically up, sym53c8xx for LSI SCSI interface "st" for tape and /proc/scsi/scsi should contain information about tape drive, e.g. SCSI ID. However none of them happened in my case! (document: "UP LTO Ultrium 2-3 - Unix Config Guide") The SCSI adapter is an LSI53C1030. The system has another the same adapter which is used for hard disk drives. The interesting part is, the hard disk are detected and even OS boots from them, but I can't make the tape drive work. Moreover, in system boot up, LSI SCSI BIOS displays informations saying there is a tape drive con...

...tiating ioc0 bringup ioc0: 53C1030: Capabilities={Initiator,Target} ACPI: PCI Interrupt 0000:04:05.1[B] -> GSI 19 (level, low) -> IRQ 19 mptbase: Initiating ioc1 bringup ioc1: 53C1030: Capabilities={Initiator,Target} Loading mptscsih.ko module Fusion MPT SCSI Host driver 3.01.20 scsi0 : ioc0: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=255, IRQ=18 Vendor: FUJITSU Model: MAP3735NC Rev: 5608 Type: Direct-Access ANSI SCSI revision: 03 SCSI device sda: 143374650 512-byte hdwr sectors (73408 MB) SCSI device sda: drive cache: write through SCSI device sda: 143374650 5...

I have a Tyan Tiger S2466 MPX motherboard with Dual Atlon MP 2800+ CPUs and 1GB PC2100 DDR SDRAM. For disk drive I have an LSI53C1030 and 4 Seagate ST336607LWs in a software raid 5 configuration. I installed Centos 4.1 and everything was fine running kernel-smp-2.6.9-11.EL. However when I upated to Centos 4.2 I have run into problems. Namely after a finite amount of disk traffic the system locks completely up. On the monitor...

I have a sles10sp3 vm that I''m trying to passthrough a scsi card, which has a DLT tape drive attached. Anyone doing anything similar? When I passthrough the scsi card (forced to do both ports), the vm dies when it loads, I think during udev. I''m viewing the vm through virt-manager, so I can''t scroll up and see what everything says. Is there a way to get the text xm

...el, low) -> IRQ 53 mptbase: Initiating ioc0 bringup ioc0: 53C1030: Capabilities={Initiator} ACPI: PCI interrupt 0000:06:02.1[B] -> GSI 29 (level, low) -> IRQ 54 mptbase: Initiating ioc1 bringup ioc1: 53C1030: Capabilities={Initiator} Fusion MPT SCSI Host driver 3.01.09 scsi0 : ioc0: LSI53C1030, FwRev=01030600h, Ports=1, MaxQ=255, IRQ=53 Using anticipatory io scheduler Vendor: SEAGATE Model: ST318406LC Rev: 8A03 Type: Direct-Access ANSI SCSI revision: 03 SCSI device sda: 35566478 512-byte hdwr sectors (18210 MB) SCSI device sda: drive cache: write...

I am currently testing an Overland Tape storage unit with a LTO-3 drive on CentOS 4.4. After a random amount of time but usually when we have backed up about 0.5-1TB we get scsi errors which cause the backup to fail. I have rebuilt the box with Solaris 10 x86 and Windoze to prove the hardware and have successfully backed up over 3TB on each OS without error. Can anyone offer advice on how to find

...) -> IRQ 19 mptbase: Initiating ioc0 bringup ioc0: 53C1030: Capabilities={Initiator,Target} ACPI: PCI Interrupt 0000:22:01.1[B] -> GSI 97 (level, low) -> IRQ 20 mptbase: Initiating ioc1 bringup ioc1: 53C1030: Capabilities={Initiator,Target} Fusion MPT SCSI Host driver 3.01.20 scsi0 : ioc0: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=19 Vendor: UNISYS Model: 014228ST118202LC Rev: B603 Type: Direct-Access ANSI SCSI revision: 02 SCSI device sda: 35833870 512-byte hdwr sectors (18347 MB) SCSI device sda: drive cache: write back SCSI device sda: 35833870 512-by...

...ingup ioc0: 53C1030: Capabilities={Initiator} mptbase: Initiating ioc0 recovery mptbase: Initiating ioc0 recovery mptbase: Initiating ioc0 recovery mptbase: Initiating ioc0 recovery mptbase: Initiating ioc0 recovery mptbase: Initiating ioc0 recovery Fusion MPT SCSI Host driver 3.01.18 scsi0 : ioc0: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=222, IRQ=10 mptscsih: ioc0: >> Attempting task abort! (sc=ffff88001f178a80) mptbase: Initiating ioc0 recovery mptscsih: ioc0: >> Attempting bus reset! (sc=ffff88001f178a80) mptscsih: ioc0: >> Attempting task abort! (sc=ffff88001f178a80) mptscsih: io...

I''m tracking performance on the machine I installed yesterday. mutt running on one Xen instance, accessing via imap to another instance, accessing via nfs the maildir in another instances, seems little laggy when moving up and down the message index list. Network latency seems low < 30ms on average. So I was tracking vmstat. On the mutt instances is seems reasonable: [nic@shell:~]