search for: jitterbuffering

Hello! I am going to use the JITTERBUFFER function in a SIP (and local channels) only setup, but have some questions of how to use it: 1. Do I need to activate jbenable in sip.conf? Or is it enough to call the JITTERBUFFER function? 2. What is the preferred way to invoke this function? Say I have channel A which is not in need of buffering, while channel B do need it. If A

WTF is a jitterbuffer? Sent from my Verizon Wireless 4G LTE smartphone -------- Original message -------- From: Matthew Jordan <mjordan at digium.com> Date: 01/29/2015 10:41 AM (GMT-05:00) To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users at lists.digium.com> Subject: Re: [asterisk-users] JITTERBUFFER function On Thu, Jan 29, 2015 at 4:56 AM,

In iax.conf there is option jitterbuffer how about sip protocol ? Are jitterbuffer can configure in sip.conf ? Thanks, for your share

Hi, I was wondering if anyone else has a similar setup and can suggest settings for the jitterbuffer: I have a client with an ADSL connection at site A & B with site A being dedicated to voice and having no Asterisk server, site B combining voice and data with traffic shaping and housing an Asterisk server. There seems to be packet loss / jitter on this connection and I wanted to know

Two asterisk boxes 150 miles apart, both cvs-head as of this morning (and since Sept 27th), connected via iax2 with low-utilized ds3 internet, C7960 calls exten on remote system (also C7960), and call goes to VM. No other calls in either system (eg, no load). Both boxes have iax config'ed as: trunk=yes allow=ilbc jitterbuffer=yes Recorded VM messages are very distorted. Changing only

> > 1. Do I need to activate jbenable in sip.conf? Or is it enough to call > > the JITTERBUFFER function? > > You only need to use the JITTERBUFFER function. > > The jbenable option will enable a jitter buffer on every channel > created for that peer (or, if global, for every peer in the system). > Depending on the version of Asterisk, it will also place the

I know, that jitterbuffer should be set at receiving side and on outgoing call leg, ie. if sipphone calls to asterisk and outgoing to zap chanel, I should set jitterbuffer on zap channel (to dejjitter audio stream from sipphone) but what about pure voip situation (i.e. iax-iax, sip-iax, skinny-iax etc.)? I have following setup (homeworkers using sip phone connected to home asterisk via SIP and

Hello, After checking out CVS HEAD from yesterday (for those new PLC/Jitterbuffer patches), I was affected by bug 3795 with my Polycom IP600's. After seing it resolved as of this morning (thanks Mark), I decided to try again... I can answer incoming calls. No problem there. Putting calls on hold, however, results in my Polycom IP600 indicating the call on hold, but the caller does

On Thu, Jan 29, 2015 at 4:56 AM, Torbjorn Abrahamsson <torbjorn.abrahamsson at gmail.com> wrote: > Hello! > > > > I am going to use the JITTERBUFFER function in a SIP (and local channels) > only setup, but have some questions of how to use it: > > > > 1. Do I need to activate jbenable in sip.conf? Or is it enough to call > the JITTERBUFFER function?

Hi, I am using the JitterBuffer. Since there is not so much documentation I think I dont use it in a correct way. All the packets are recieved (I control the sequence numbers) but the JitterBuffer often tells me he has no packet. I am using it in the following way: I am not sure if I use the ticks correctly but I think it can be set to 20(msec). It is set as a Member in my class and i

Hi guys, I 've tried asterisk 1.2.2. It work flawlessly for about 3 days then at the third days I activated setting jitterbuffer=yes and suddenly there is no voice when the call is picked up. It's really weird as if asterisk stops sending rtp packet. I've checked asterisk log and found nothing suspicious. Just weird :S. I tried it in 3 asterisk server and all of them are having

I find that DTMF does not work reliably if jitterbuffer=on for certain IAX providers. For instance, DTMF tones are missed entirely about half the time when I dial into an exgn.net account. However, it always works fine for an unlimitel.ca account. Someone else has seen this too: http://bugs.digium.com/view.php?id=6011 Can anyone suggest a workaround (other than jitterbuffer=off)? - Mike

I was using G729 with Asterisk 1.07. With the new ability to do packet loss correction with ILBC, I felt I'd give it a try. The new PLC does not work with G729. I don't use Speex because my softphone does not support it. This is a 1.5mb IP-VPN connection with prioritized QOS for port 4569 (IAX2). I've never really stressed the bandwidth. Typically, only 10-20 concurrent calls.

I've been having problems with incoming IAX2 calls - some work, but a large fraction are answered with "dead air" or disconnects from my IAX provider. Disabling the jitterbuffer seems to eliminate the problem (so far)! Has anyone else seen this? I'm using 1.2.6, but I'm not sure what my provider is using. A snippet of the a failed incoming call IAX2 debug is attached

Thanks for your reply Jean-Marc! this was what I had before. But I decided to restructure it since the thread that plays the sound is a callback from the sound hardware, more or less an interrupt handler. For me it seems more reasonable to waste some memory for to save the decompressed Packet. While I write this I begin to think that it is possible I decompress Packets that are never used

What is the consensus on using the 1.4 jitterbuffer? Do most people enable it? We have a "PSTN" server that has our RBS T1 trunks in a central location, then have clients that connect via SIP to us for access to those trunks. Most of them are just fine, but lately we have a handful that are having latency and jitter issues. I am hesitant to just turn on the jitter buffer in

Hi, I have a question about jitterbuffer and PLC. I use Asterisk 1.6.2.0 and 1.6.0.20 or older. I use uLaw. My system map: ============================================================================= [ asterisk 2 ] -- # LOSS # -- # A # -- [ asterisk 1 ] -- # B # -- [ X-lite ] ============================================================================= I use two asterisk server.

Hi, We have Asterisk, running on a P4 box running Suse 9.1, making calls using IAX through SimpleTelecom and Nufone. What we are looking for is toll quality voice. The problem is that voice over calls routed through SimpleTelecom and nNufone occassionally breaks. We also have a digium card and the calls over the digium card using the Zaptel Interface have a very good quality. We

Are these things possible? 1) Set the local Asterisk jitterbuffer size, but only for a particular connection. I'd like to force Asterisk to use a particularly large buffer in certain cases. Should I expect this to work? [general] jitterbuffer=no register => username:password@parcelfarce.domain.net ;parcelfarce register => username:password@iaxtel.com ;iaxtel [parcelfarce]