search for: isdn30s

Hi, Are there any hardware for ISDN30 ? if yes any problem with this ? is i out-of-box like ISDN2 but with 30 linies ? Do I need more than the cable from my teleprowider and a PCI-card ? /HHA _________________________________________________________________ Find high-speed ‘net deals — comparison-shop your local providers here. https://broadband.msn.com

anybody recommend a supplier in the UK for a pri/isdn30 line (other than BT) thanx very much __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

Hi :) My employer is looking to move a call centre to a new office, and has been increasingly frustrated with their legacy PBX (call-logging licensing and hardware upgrade costs). So I've stepped forth as the Open Source Pedant and suggested Asterisk so we can do all our own CallerID / call logging / analyses, and make use of IP Phones / teleworking, etc. The problem begins in that I only

Quoth Jon Morgan <jon.morgan at motors.co.uk> > >We have a 2 port Digium TE220P card, one span is configured to connect to our ISDN30 provider (British Telecom), the other span connects to our internal PBX. Here's the zaptel.conf snip: > >span=1,1,0,ccs,hdb3,crc4 >bchan=1-15 >dchan=16 >bchan=17-31 > >span=2,0,0,ccs,hdb3,crc4 >bchan=32-46 >dchan=47

Hi All, Has anyone hooked up * as an extension/trunk of an Avaya system that has around 2 ISDN30e's. Trying to add 100 extensions to one of our systems, but not sure where to start reading. Thanks. -- Kind Regards, Gavin Henry.

We are trying to configure a Sangoma A101 card to allow both incoming and outgoing calls on a UK (BT) ISDN30e line with only 24 channels enabled. At present incoming calls work fine. We can't call out -- we get a BUSY/CONGESTED error. Do we need another context in our zapata.conf? In other words, do we need to reserve, say, channels 17-24 for outgoing calls? I also wonder if the signalling

>> So it sounds like it should "just work". I'll let you know in a few >> weeks time :) > TDM400P to E1/T1 card faxing fails by design. The lack of > synchronisation between cards means it can *never* work with any > reliability. The hardware will not permit it. >> >> (And I know I've asked this before, but any recommendations for a >>

Hello, I have a Sangoma A101 connected to an ISDN30 (E1 in the UK) with some Snom 300 and Idefisk softphones. I can do SIP and IAX2 calls just fine, however I cant get any audio in either direction on the Zap channels. When I call in or dial out over the ISDN30 (UK E1) I can see the call answered/placed on the CLI and then silence follows. I've been provisioned 25 out of the 31 channels only

I'm just curious to know if anyone is using a usb 2.0 / ISDN30 (specifically EuroISDN) device. We are looking to purchase another pci card, but was wondering if anyone has any horror / success stories to share regarding a usb device. TIA Julian

Hello, I'm trying to connect a Digium Wildcard TE110P T1/E1 Card to a 10 channel BT ISDN 30 box, however I'm fairly new to Asterisk and this is the first time I've set-up a telephony interface card can anyone give me some pointers or known working configurations? I'm running Asterisk 1.6 and Dahdi 2.4.1.1. Thanks, Tanuki -------------- next part -------------- An HTML attachment

On how to even search for this "feature" as I have no idea on what it can be. I've got a meridian linked to * (by EuroISDN) which is linked to a ISDN30. I can make calls from the meridian, and receive calls into the meridian. Great stuff. However, if someone dials an invalid number, then instead of hearing a "three tone", the line just drops and goes dead. The console

I have a couple of numbers that are diverted to a number that is conected to an isdn30 card, running asterisk 1.4. eg. 123456 => 22334455 654321 => 22334455 What I would like to know is the number of the orginal number dialled (123456 or 654321). I thought that RDNIS was the answer, but it is always coming up blank. When I did a debug on the pri span, I saw the following message

We will be connecting our Asterisk server to ISDN 30 and intend using the Sangoma A101 card. The install location is in London (UK). Sangoma card at Voipon http://www.voipon.co.uk/sangoma-a101-pri-isdn-card-p-132.html?gclid=CI32vJz22I0CFQXklAodIgjHaA I would be grateful to hear if this is the right choice of card. Usage reports would be helpful. Regards Rory -- Rory Campbell-Lange

Thanks to help on this list and Sangoma's support we have incoming and outgoing calls passing through asterisk. However both incoming and outgoing calls are greeted by silence. I've noted our existing config below with our test extensions.conf. Help much appreciated Rory Zaptel ----------------------------------------------------------------------- loadzone=uk defaultzone=uk #Sangoma

My employer wants to use Asterisk, but the E1 circuit providing the current phone system is DASS2 rather than ISDN30. Converting the E1 to ISDN30 is not a practical proposition at this time as it'd stop the legacy phone system from working. Is there any sort of hardware support for DASS2? I speculate that the E100P should be able to deal with the electrical side of it, but I'm unsure of

Dear All, Thank you for taking the time to read this post - I am *confused!* as to why my asterisk setup does not work as it should. I have an ISDN 30 connection for telephony, a Sangoma card, and asterisk installed. Incoming calls, and outgoing calls work 100%. Making an international call, results in silence, or the error message all circuits are busy Numbers being passed to the trunk for

Greetings to one and all on this fine list; We have the current system: Meridian 1 Option 11 +-------------------+ | | ISDN/30 (DASS/2) ===> |NTAK79BB (2MB Pri) | | |<-->4x16 port Digital / 1x16 port Analogue ISDN/30 (EUROIDSN) ===> |NTBK50AA (2MB Pri)

Hi there Just a quick question, I will be building some servers in a lab utilizing Digium E1 cards. I would like if possible to avoid the expense of installing an e1/ISDN30 in my lab. I have two questions really, first does anybody know of an effective simulation tool I can use to replicate a real world PRI but without the telco line being installed. And secondly, can I have a scenario with 2

A client used to use BT isdn30 and ported the numbers to telewest several years ago. Now, the client moved to adept telecom. I *think* adept resells BT products. We got new numbers from adept (bt?) and the old pbx on the telewest lines forwards the calls to the new numbers. On the adept line I got a digium card in an opteron supermicro server. ztcfg gives me over 99.99 pretty much all the time.

Ok Guys, I've done a tonne of hunting around on this problem, but can't find much help. I'm running: asterisk 1.4.19.1 libpri 1.4.3 and zaptel 1.4.9.2 which I believe has been modified by RedFone to add the ztd-ethmf module. My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic PBX on span 4. Upon