search for: hiddev0

Greets all; I was just booted to mdv-2010-x64 where I found my lack of sound problems. Whoopy ding... But when I rebooted to fedora, now the driver cannot disconnect and gain access to the ups. I installed the 52-nut udev file in /etc/udev.d, and it reads that it should setup /dev/hiddev0 like this and with 0664 perms when it finds that ups: crw-rw-r-- 1 root nut 180, 0 2010-01-03 20:51 /dev/hiddev0 where hiddev0 is the ups port. But now the usbdrvctl, using usbhid-ups as the driver, reports: [root at coyote etc]# upsdrvctl start Network UPS Tools - UPS driver controller 2.4.1...

...red as connecting in /var/log/messages eg usb 3-1: USB disconnect, address 3 usb 3-2: new low speed USB device using uhci_hcd and address 4 But I don't know how to progress from here. I have used the following commands: mkdir /dev/usb mkdir /dev/usb/hid mknod /dev/usb/hid/hiddev0 c 180 96 mknod /dev/usb/hid/hiddev1 c 180 97 mknod /dev/usb/hid/hiddev2 c 180 98 mknod /dev/usb/hid/hiddev3 c 180 99 However, I'm not sure how to check that there is a link between hiddev0 and the USB device that's registering above. - In a fit of woeful optimism I have configured ups.con...

...UPS CS 350 I downloaded the stable nut tar.gz installed it. This is not the first time i install and configure nut so i used the same configuration as on my other server as i always did. Then i made the 2 required modification. I changed these 2 thing: driver = apcsmart port = /dev/hiddev0 # ls -al /dev/hiddev0 crw------- 1 nut nut 180, 96 Nov 27 09:07 /dev/hiddev0 When i try to start nut i get the following : # upsdrvctl start Network UPS Tools - UPS driver controller 2.2.0- Network UPS Tools (version 2.2.0-) - APC Smart protocol driver Driver version 1.99.8, command table versi...

hi i have a belkin ups here some setting chmod 0600 /dev/hiddev0 chown nut:root /dev/hiddev0 linux:/home/sonia # /usr/lib/ups/driver/upsdrvctl start Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools: New USB/HID UPS driver 0.28 (2.0.4) No matching USB/HID UPS found Driver failed to start (exit status=1) linux:/home/sonia # /usr/lib/ups/driv...

Hi, is there a way to use my Belkin F6H650 on the USB port? I already installed usbhid-support, but neither the hidups worked (reports "/dev/usb/hiddev0 is not a UPS") nor genericups with upstype=7 and the hiddev set as device ("ioctl TIOCMSET: Invalid argument") worked. I have installed the debian sarge package of nut 2.0.1 (2.0.1-4) Regards, Philipp

...productid (like -x productid=1234) when using newhidups? just thought i'd try it with the F6C1500-TW-RK over usb. i was able to get hidups to work using the below settings, but it provides limited information. my ups.conf entry: [belkin] driver = hidups port = /dev/usb/hiddev0 and the output of upsc: gateway:/etc/nut# upsc belkin@localhost battery.charge: 100 battery.chemistry: PbAc battery.runtime: 120 battery.voltage: 12.5 driver.name: hidups driver.parameter.port: /dev/usb/hiddev0 driver.version: 2.0.1 ups.mfr: Unknown ups.model: Belkin UPS ups.serial: ups.status:...

...what I see when I run "service ups start": Starting hidups: Network UPS Tools: HID UPS driver 0.13 (2.0.1) Warning: This is an experimental driver. Some features may not function correctly. Detected American Power Conversion Back-UPS Pro 500 FW:16.5.D USB FW:a7 on port /dev/hiddev0 Ignoring x86 page event 0xff860060 (8) Ignoring x86 page event 0xff860060 (8) [ OK ] Starting upsd: Network UPS Tools upsd 2.0.1 Connected to UPS [myups]: hidups-hiddev0 Synchronizing...done [ OK ] Starting UPS monitor (master): Network UPS Tools upsmon 2.0.1 UPS...

...1&NoMapp=0 i use suse 10.1, i installed nut the ups is connected directely to my computer with an usb cable lsusb return Bus 001 Device 004: ID 0d9f:0001 Powercom Co., Ltd with lsmod, i can see usbhid 43296 0 /etc/ups/ups.conf i tried powercom and newhidups driver = newhidups port = /dev/hiddev0 desc = "Local UPS" /etc/ups/upsd.conf ACL all 0.0.0.0/0 ACL localhost 127.0.0.1/32 ACCEPT localhost REJECT all /etc/ups/upsmon.conf MONITOR myups@localhost 1 upsmaster okeefe master MINSUPPLIES 1 SHUTDOWNCMD "/sbin/shutdown -h now" NOTIFYCMD /usr/lib/powersave/powersave-no...

...d with NUT... I know my system can SEE the UPS, as DMESG shows this: hiddev96: USB HID v1.10 Device [APC Back-UPS ES 650 FW:818.w1.D USB FW:w1] on usb-0000:00:04.2-1 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver I can see an entry in /dev/usb called hiddev0 I have updated my ups.conf file as follows: [apc] driver = newhidups port = /dev/usb/hiddev0 desc = "APC Back-UPS ES 650" Note, that port used to be set to auto, but in deperation, I hardcoded it.. I'm running kernel version 2.6.17.3, and have libusb-0.1.so...

...t enabled. Fixed that. Copied the drivers from the trunk sub-directory to the Debian 2.0.5 package drivers directory, and built the package that way. That seems to have given me some partial success. newhidups sees a device but won't talk to it: # /lib/nut/newhidups -u root -DDDD /dev/usb/hiddev0 Network UPS Tools: 0.28 USB communication driver 0.28 - core 0.30 (2.0.5) debug level is '4' Checking device (09AE/4003) (002/002) - VendorID: 09ae - ProductID: 4003 - Manufacturer: Tripp Lite - Product: TRIPP LITE UPS - Serial Number: 9530ALCPS519400017 - Bus: 0...

ut 2.4.1 works with megatec_usb driver. It tries to interact with a device in /dev/bus/usb/X/Y, but there are root:root 664 access rights. When I try to set port /dev/hiddev0 with write access in config file, in strace there are no records about accessing /dev/hiddev, but still only /dev/bus/usb/X/Y How to explain such a behavior? execve("./megatec_usb", ["./megatec_usb", "-a", "ups", "-u", "stalker", &quo...

....929480] usb 1-10: New USB device found, idVendor=050d, idProduct=0751 [136322.929486] usb 1-10: New USB device strings: Mfr=4, Product=20, SerialNumber=0 [136322.929489] usb 1-10: Product: Belkin UPS [136322.929491] usb 1-10: Manufacturer: Belkin [136323.695058] hid-generic 0003:050D:0751.0008: hiddev0,hidraw6: USB HID v1.11 Device [Belkin Belkin UPS] on usb-0000:00:02.0-10/input0 So is this usb-0000:00:02.0-10/input0 a valid way to give nut a path to it, and if so, what file do I add that too? I also note that in the original bootup discovery it was hiddev0/hidraw6, the same as the latest...

...sys/module/usbcore/parameters/autosuspend -1 [root at localhost ~]# tail -f /var/log/messages Jun 24 13:37:33 localhost kernel: usb 2-2.1: Product: Tripp Lite UPS Jun 24 13:37:33 localhost kernel: usb 2-2.1: Manufacturer: Tripp Lite Jun 24 13:37:33 localhost kernel: hid-generic 0003:09AE:2012.0005: hiddev0,hidraw1: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:02:02.0-2.1/input0 Jun 24 13:37:48 localhost kernel: usb 2-2.1: USB disconnect, device number 7 Jun 24 13:37:51 localhost kernel: usb 2-2.1: new low-speed USB device number 8 using uhci_hcd Jun 24 13:37:51 localhost kernel: usb...

...ld re-master cd. Boot from knoppix live cd and get these problems (on same PC as knoppix hdd install): Upsdrvctl start After a few minutes I get an error of: Startup timer elapsed, continuing?.. At this stage I find that lsusb now locks up and upon further investigations I find that /dev/usb/hiddev0 has now been deleted (including the directory /dev/usb) Re-boot is necessary. Run lsusb & HP 1000 is found Change permissions on /dev/usb to full read/write access & the same to /dev/usb/hiddev0 Tried: ./lib/nut/usbhid-ups -DDD -u root -a testups I get a summary of: =====================...

...9:25:27 localhost kernel: usb 2-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 May 29 19:25:27 localhost kernel: usb 2-2.1: Product: Tripp Lite UPS May 29 19:25:27 localhost kernel: usb 2-2.1: Manufacturer: Tripp Lite May 29 19:25:27 localhost kernel: hid-generic 0003:09AE:2012.0004: hiddev0,hidraw1: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:02:02.0-2.1/input0 May 29 19:25:29 localhost upsd[6287]: UPS [TrippLiteUPS] data is no longer stale May 29 19:25:29 localhost upsd: UPS [TrippLiteUPS] data is no longer stale May 29 19:25:45 localhost kernel: usb 2-2.1: USB dis...

...; > Bus 002 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 = > Serial > > > Port > > > Bus 002 Device 001: ID 0000:0000 > > > Bus 001 Device 001: ID 0000:0000 > > > miles:/usr/src/nut/trunk# /lib/nut/newhidups -x bus=3D002 > > > /dev/usb/hiddev0 > > > Network UPS Tools: 0.28 USB communication driver 0.28 - core 0.30 > > > (2.1.0) > > > > > > No matching HID UPS found > > > miles:/usr/src/nut/trunk# /lib/nut/newhidups -x bus=3D002:003 > > > /dev/usb/hiddev0 > > > > > >...

...:00:1d.0/usb6/6-1 (usb) KERNEL[1308961682.709615] add /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0 (usb) KERNEL[1308961682.709674] add /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/0003:050D:1100.0007 (hid) KERNEL[1308961682.979776] add /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/usb/hiddev0 (usb) KERNEL[1308961682.979802] add /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/0003:050D:1100.0007/hidraw/hidraw0 (hidraw) However, the usb devices are created in root group and without read access to nut group. $ ls -l /dev/usb crw------- 1 root root 180, 96 2011-06-24 20:43 hiddev0 Packa...

...-blazer1000-spec.htm and brochure http://www.centralion.com/dm-download/Blazer1-2K/Blazer1K-2K.zip) This UPS use megatec protocol over USB I think. Below are details catch from the console : When I plug the UPS on the USB port I get : # lsusb Bus 003 Device 005: ID 0665:5161 If I do cat /dev/usb/hiddev0 the system seems to be reading on the device but no characters appears on the console... If I unplug the UPS the cat /dev/usb/hiddev0 command stop working so I think the system see the UPS on this device. The usbview show me this on the device : USB to Serial Manufacturer: Cypress Semiconductor...

...-blazer1000-spec.htm and brochure http://www.centralion.com/dm-download/Blazer1-2K/Blazer1K-2K.zip) This UPS use megatec protocol over USB I think. Below are details catch from the console : When I plug the UPS on the USB port I get : # lsusb Bus 003 Device 005: ID 0665:5161 If I do cat /dev/usb/hiddev0 the system seems to be reading on the device but no characters appears on the console... If I unplug the UPS the cat /dev/usb/hiddev0 command stop working so I think the system see the UPS on this device. The usbview show me this on the device : USB to Serial Manufacturer: Cypress Semiconductor...

...UPS ES 500 connected via USB. I built nut 2.0.2 from source and am attempting to get it to work. I had to manually create the device links and I think it's ok because hidups is recognizing the UPS but any attempts to read data from it fail: [root@server bin]# ./hidups -D -D -D /dev/usb/hid/hiddev0 Network UPS Tools: HID UPS driver 0.13 (2.0.0) Warning: This is an experimental driver. Some features may not function correctly. debug level is '3' Detected APC Back-UPS ES 500 FW:801.e5.D USB FW:e5 on port /dev/usb/hid/hiddev0 dstate_init: sock /var/state/ups/hidups-hiddev0 open on fd 5...