Displaying 20 results from an estimated 23 matches for "featd".
Did you mean:
feats
2004 Jul 23
6
Robbed Bit T1 Configuration
Is it possible to control the dialing format used when making a call from
asterisk separately from the inbound format? In my case I have a single
robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P.
This configuration works fine for inbound calls, however when an outbound
call is made on this same T1 asterisk dials outbound in the featd format. I
need asterisk to only dial the phone number in the dial string (no more, no
less), but as I said before aster...
2004 Aug 23
2
Question about dial out via Zap
Group
When I dial a phone number that should go out to the telco my local
phone rings. Does anyone have any hits ?
Thanks
Asterisk Ready.
*CLI> -- Called g1/6144196143
Urgent handler
Urgent handler
-- Starting simple switch on 'Zap/2-1'
Urgent handler
Urgent handler
-- Called 6149236651
Urgent handler
-- SIP/6149236651-1d93 is ringing
Urgent handler
-- Zap/1-1
2009 Mar 03
2
Asterisk analog DID with Adit 600
...ng. I've set asterisk to use E&M in both dahdi/system.conf and
chan_dahdi.conf.
If I dial the port connected to the DID card it goes off hook but when
the Executone winks Asterisk or the Adit thinks the remote side has hung
up and terminates the call.
I've tried using E&M wink, featd, and featb signalling in
chan_dahdi.conf, set hanguponpolarityswitch=no, and tried loop start
signalling for the heck of it and that didn't work either.
Does anyone have any suggestions of additional things I could try?
Thanks in advance,
-Dave
2006 Jun 02
4
Problems and questions with setting up a Feature Group D trunk to a Nortel DMS-10 switch
I currrently have Asterisk 1.2.8 with a TE110P Zaptel card tied to our Nortal DMS-10 switch via T1.
This T1 trunk is configured for Feature Group D MF.
The purpose of this is for LD delivery to a VoIP LD provider as a LD choice for our customers off of the DMS-10.
When I sieze a channel on the zaptel, I get a spill of digits from the switch that is the called number, and I can see that in
2003 Mar 03
40
callerid
"In general you can match callerID with the /, but if you don't put
anything after the /, then the rule matches "no caller*ID", and if no
slash is there at all, it matches "any callerid". "
Ok.My question is ->
how to match callerid from 001... ?
and if don't know how many numbers ?
exten => s/0_,Answer don't work-
anything else ?
tnx
Thomas
2008 Jun 09
1
Long call setup with non-PRI T1
...We have
managed to get CPN and the extension outpulsed from the switch, but call
setups are really slow.
Our T1's are set up as E&M Wink, and they send us the last 5 digits
dialed followed by the 10 digit calling party number (we couldn't get
the switch to be happy with *CPN*+5* to use featd).
We are using asterisk 1.4.19.
Watching the DTMF debugging info, it doesn't take too terribly long to
get the digits (maybe 1-1.5 seconds), but after getting the digits
asterisk waits another 3 seconds before doing anything.
In chan_zap.c, there is a 'matchdigittimeout' that is set...
2005 May 23
2
E&M Tie Line
How do I setup my T1 card as an E&M tie line? Any special
configuration?
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm
2005 Jun 21
5
Problem with Connecting PBX to Asterisk
...X T1 config is set to ESF, B8ZS and E&M Wink.
My zaptel.conf has the following:
Span=2,0,0,esf,b8zs ;connecting port 2 of TE405P card to pbx, leaving port
1 for porting telco later
e&m=25-48
loadzone=us
defaultzone=us
my Zapata.conf has the following:
group=1
context=default
signalling=featd ; em_w ;have been trying both in various combinations
switchtype=national
channel => 25-48
my extensions.conf has the following sample dialplan:
exten => 233,1,Dial(Zap/g1/9233)
exten => 241,1,Dial(Zap/g1/9241)
exten => 253,1,Dial(Zap/g1/9253)
I want that if someone calls in to aste...
2005 May 12
2
Inbound ANI & DNIS format
Hello,
Being totally fed up with the lack of quality and reliability from both
VoicePulse and BroadVoice,
We are switching to a direct IP connection to Global Crossing. We've
installed a local point-to-point T1 into their CO, and they will
give/take SIP g729a directly and act as the gateway for us.
In setting up the inbound SIP service, they are asking the question, "In
what format do
2005 Oct 04
2
Quad PRI Problems
...2
span=4,1,0,esf,b8zs # Connects to Brook Trout CArd
e&m=1-4
defaultzone=us
loadzone=us
[channels]
context=from-internal-receiver ; Points to the default context of your
extensions.conf
language=en
faxdetect=none
usecallerid=yes
callerid=asreceived
threewaycalling=yes
transfer=yes
signalling=featd ; FXS for ringing phones
group=0
flash=350
rxwink=300
prewink=20~~
echocancel=no ; You can set this to 32, 64, or 128, tweak to your needs.
echocancelwhenbridged=no
immediate=no
channel => 1-24
signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master
switchtype=national
pridialplan=unkno...
2004 Jan 30
9
Adtran 750 DID question.
Hello All,
I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They
2006 Jun 17
0
T1 + E&M
...ontext=from-did
group = 3
channel => 25-48
=============================
I've searched for alternatives signalling types and found these. But
nothing was found as to
exactly what happens during inbound or outbound calls - (is dial tone
provided or not)
a.. em_w: E & M Wink Start
a.. featd: Feature Group D (The fake, Adtran style, DTMF)
a.. featdmf_ta: Feature Group D (The real thing, MF (domestic, US)) through
a Tandem Access point
a.. fgccama Feature Group C-CAMA (DP DNIS, MF ANI)
a.. fgccamamf Feature Group C-CAMA MF (MF DNIS, MF ANI)
a.. featdmf: Feature Group D (The real thing,...
2005 Aug 22
0
Does Asterisk support T1 E&M Wink/Wink voicechannels on any Digium/Sangoma hardware?
I could only get *ANI*DNIS* working one way and that was setting my
signalling type on the Asterisk side to 'featd' The Definity won't send
*ANI*DNIS* information back to the asterisk as far as I can tell.
Other than that, I've been running it with wink/wink E&M for a while
now. TN464 circuit pack on the definity side, te110p on the asterisk
side. Just a crossover cable between the boxes.
-...
2006 Jun 17
0
E&M + Dial tone
...context=from-did
group = 3
channel => 25-48
=============================
I've searched for alternatives signalling types and found these. But
nothing was found as to
exactly what happens during inbound or outbound calls - (is dial tone
provided or not)
a.. em_w: E & M Wink Start
a.. featd: Feature Group D (The fake, Adtran style, DTMF)
a.. featdmf_ta: Feature Group D (The real thing, MF (domestic, US)) through
a Tandem Access point
a.. fgccama Feature Group C-CAMA (DP DNIS, MF ANI)
a.. fgccamamf Feature Group C-CAMA MF (MF DNIS, MF ANI)
a.. featdmf: Feature Group D (The real thing,...
2005 Jul 14
0
PRI Channel Question
...m to refuse the caller.
MAtt, I am trying to figure out how or where asterisk is messing with
these codes?
Here are my settings
[zapata.conf]
[channels]
context=from-internal-receiver ; Points to the default context of your
extensions.conf
language=en
faxdetect=none
usecallerid=yes
signalling=featd ; FXS for ringing phones
callerid=asreceived
group=0
threewaycalling=yes
transfer=yes
flash=350
;rxflash=350
rxwink=300
prewink=20~~
echocancel=no ; You can set this to 32, 64, or 128, tweak to your needs.
echocancelwhenbridged=no
immediate=no
channel => 1-24
signalling=pri_cpe ; pri_cpe = PRI s...
2005 May 11
0
T1 Card ------ Adtran ------- FXS BUG???
...it may be a bug, but not sure.
Ronald.
PS> I am happy to pay for services rendered provided a solution can be
had.
/etc/zaptel.conf
span=1,1,0,esf,b8zs
e&m=1-24
defaultzone=us
loadzone=us
/etc/asterisk/Zapata.conf
language=en
context=from-pstn
faxdetect=none
usecallerid=yes
signalling=featd ; FXS for ringing phones
echocancel=yes ; You can set this to 32, 64, or 128, tweak to your
needs.
echocancelwhenbridged=yes
echotraining=400 ; Asterisk trains to the beginning of the call, number
is in milliseconds
callerid=asreceived
group=1
threewaycalling=yes
transfer=yes
rxwink=300
rxflash=700...
2005 Mar 17
4
Caller ID on E&M Wink
I am an Asterisk newby, and I cannot seem to get Caller ID information
from our T1 line. When calls appear at the phones, they say the call
came from "asterisk" and unknown number.
I know how Caller ID information is passed on an analog phone line
(between the rings) but with a T1 line, I don't know technically how it
is done.
I don't see the caller's number in the
2004 Jul 03
1
Caller ID and DNIS Problems (Non-Pri T1)
I am trying to receive both CID and DNIS from the telco through a
non-pri T1. Currently I have the T1 setup and operational both outbound
and inbound calls are completed as should be expected. The calls came
in and were placed in the context specified in zapata.conf on exten =>
s,1.
I have requested that the telco provide callerid (they call it ANI)
along with 10 digit dnis for my 800
2004 Jun 16
0
(no subject)
...ISDN
; local: Local ISDN
; national: National ISDN
; international: International ISDN
;
;pridialplan=national
;
; Overlap dialing mode (sending overlap digits)
;
;overlapdial=yes
;
; Signalling method (default is fxs). Valid values:
; em: E & M
; em_w: E & M Wink
; featd: Feature Group D (The fake, Adtran style, DTMF)
; featdmf: Feature Group D (The real thing, MF (domestic, US))
; featb: Feature Group B (MF (domestic, US))
; fxs_ls: FXS (Loop Start)
; fxs_gs: FXS (Ground Start)
; fxs_ks: FXS (Kewl Start)
; fxo_ls: FXO (Loop Start)
; fxo_gs: FXO (Ground St...
2005 Feb 10
0
Asterisk 1.0.5 won't pick up incoming calls
...work
; with all telcos.
;
; outofband: Signal Busy/Congestion out of band
with RELEASE/DISCONNECT
; inband: Signal Busy/Congestion using in-band
tones
;
; priindication = outofband
;
;
; Signalling method (default is fxs). Valid values:
; em: E & M
; em_w: E & M Wink
; featd: Feature Group D (The fake, Adtran style,
DTMF)
; featdmf: Feature Group D (The real thing, MF
(domestic, US))
; featb: Feature Group B (MF (domestic, US))
; fxs_ls: FXS (Loop Start)
; fxs_gs: FXS (Ground Start)
; fxs_ks: FXS (Kewl Start)
; fxo_ls: FXO (Loop Start)
; fxo_gs: FXO (Ground St...