search for: eth6

...<vlan> <tag id='44'/> </vlan> <alias name='hostdev0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/> </interface> In host ip link 23: eth6: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/ether 38:ea:a7:8f:fa:98 brd ff:ff:ff:ff:ff:ff vf 0 MAC 52:54:00:60:7f:57, vlan 44 In guest modprob 8021q eth1 Link encap:Ethernet HWaddr 52:54:00:60:7F:57 inet6 addr: fe80::...

...etely > disabling it, disabling CPU frequency scaling, and setting pcie_aspm=off > on the kernel command line. Are there other kernel options that might > be useful to try? May I chip in here? In our environment we're randomly seeing: Jan 17 23:40:14 xen01 kernel: ixgbe 0000:04:00.1 eth6: Detected Tx Unit Hang Jan 17 23:40:14 xen01 kernel: Tx Queue <0> Jan 17 23:40:14 xen01 kernel: TDH, TDT <9a>, <127> Jan 17 23:40:14 xen01 kernel: next_to_use <127> Jan 17 23:40:14 xen01 kernel: next_to_clean <98> Jan 17 23:4...

...hostdev.3E <http://wiki.libvirt.org/page/Networking#Assignment_with_.3Chostdev.3E> Assignment from a pool of SRIOV VFs in a libvirt <network> definition Assignment with <interface type='hostdev'> (SRIOV devices only) <network> <name>passthrough-eth6</name> <forward mode='hostdev' managed='yes'> <pf dev='eth6'/> </forward> </network> I launch the vm, there is a vm with virt-install .... --network network=passthrough-eth6 I inject traffic with a generator so I def...

...ollowing setup below: - +-------------+ | br0 | | -> eth1 | -> DSL_1 | -> eth2 | +-------------+ | br1 | | -> eth3 | -> DSL_2 | -> eth4 | +-------------+ | br2 | | -> eth5 | -> DSL_3 | -> eth6 | +-------------+ br0 has eth1 and eth2; br0 has no ip address br1 has eth3 and eth4; br0 has no ip address br2 has eth5 and eth6; br0 has no ip address The traffic of DSL_1 ISP will pass thru br0. The traffic of DSL_2 ISP will pass thru br1. The traffic of DSL_3 ISP will pass thru br2...

Hi, I have 8 ethernet cards installed. Is it possible to use eth0-eth6 as the net interface for shorewall and eth1 as the lan network? Thanks. sangprabv sangprabv@gmail.com ------------------------------------------------------------------------------

On 01/27/2017 06:08 AM, Karel Hendrych wrote: > Have you tried to eliminate all power management features all over? I've been trying to find and disable all power management features but having relatively little luck with that solving the problems. Stabbing the the dark I've tried different ACPI settings, including completely disabling it, disabling CPU frequency scaling, and setting

Hi, I met a problem when using bridge with netfilter. The kernel version 2.4.20, and the patch is bridge-nf-0.0.10-against-2.4.20.diff. Our firewall configuration is as follows, eth3,eth4,eth5,eth6 configured as a bridge with an IP address 10.0.0.1. The local net connect to the internet via the gateway 10.0.0.1 and SNAT is applied on the firewall. It worked but sometimes there are some problems. The bridge stopped resonse now and there. When checking the log there were some messages as belo...

...Articles/145406/ Just in case some commands output: root@server1:/backup/ftp# ip ro ls table adsl 192.168.10.37 via 192.168.90.3 dev eth2 192.168.100.0/24 dev eth1 proto kernel scope link src 192.168.100.1 192.168.50.0/24 dev eth2 proto kernel scope link src 192.168.50.1 192.168.3.0/24 dev eth6 proto kernel scope link src 192.168.3.2 192.168.2.0/24 dev eth5 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev eth4 proto kernel scope link src 192.168.1.2 192.168.90.0/24 dev eth2 proto kernel scope link src 192.168.90.1 default proto static nexthop via 192.168.1.1...

...ons that might >> be useful to try? > > May I chip in here? In our environment we're randomly seeing: Welcome. It's a relief to know someone else has been having a similar nightmare! Perhaps that's not encouraging... > Jan 17 23:40:14 xen01 kernel: ixgbe 0000:04:00.1 eth6: Detected Tx Unit > Hang > Jan 17 23:40:14 xen01 kernel: Tx Queue <0> > Jan 17 23:40:14 xen01 kernel: TDH, TDT <9a>, <127> > Jan 17 23:40:14 xen01 kernel: next_to_use <127> > Jan 17 23:40:14 xen01 kernel: next_to_clean...

On 30 January 2017 at 22:17, Adi Pircalabu <adi at ddns.com.au> wrote: > May I chip in here? In our environment we're randomly seeing: > > Jan 17 23:40:14 xen01 kernel: ixgbe 0000:04:00.1 eth6: Detected Tx Unit > Hang > Someone in this thread: https://sourceforge.net/p/e1000/bugs/530/#2855 reported that *"With these kernels I was only able to work around the issue by disabling tx-checksumming offload with ethtool."* However, that was reported for Kernels 4.2.6 / 4.2.8...

...em have 2 lan-card with access to internet. >> >> Evertything works almost fine, except that I've configured on each guest >> the static configuration of the bridge with the ip address, like this: >> >> auto lo >> iface lo inet loopback >> >> auto eth6 >> iface eth6 inet static >> address 192.168.1.41 >> network 192.168.1.0 >> netmask 255.255.255.0 >> gateway 192.168.1.10 >> >> >> >> So are you saying that you're attempting to give each guest the *same* IP >> address? There's no...

...dd processes can't start. And there is below warning info in log.nmbd and log.winbindd. Please give your suggestions and thx. pekwj42a-> # cat /usr/lib/smb.conf # Samba config file created using SWAT # from UNKNOWN (140.231.210.142) # Date: 2012/02/09 12:45:34 [global] interfaces = eth6 [sap_capps] comment = sap AP1 interface path = /export/capps/AP1 valid users = cn1wj026 read only = No [sap_interface] comment = sap AP1 interface path = /export/capps/AP1/Interface read only = No [sap_edi] comment = sap AP1 edi...

...ess}=="00:1e:67:81:37:0e", ATTR{type}=="1", KERNEL=="eth*", NAME="eth5" SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="90:e2:ba:46:ef:30", ATTR{type}=="1", KERNEL=="eth*", NAME="eth6" SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="90:e2:ba:46:ef:31", ATTR{type}=="1", KERNEL=="eth*", NAME="eth7" After reboot it worked fine for all 3 servers, but some time later after another reboot I get...

Hi, I don't have ifcfg-eth1 in my /etc/sysconfig/network-scripts. But when I do ifconfig eth1 I can see output as below. If I do ifconfig eth12 , I don't see anything which i am assume is normal. eth1 Link encap:Ethernet HWaddr 00:24:E8:44:DB:CC BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0

...0 iface br0 inet static address 192.168.5.11 netmask 255.255.255.0 bridge_ports eth0 eth1 # The external network interface auto br1 iface br1 inet static address [public ip address] netmask 255.255.0.0 bridge_ports eth2 eth3 eth4 eth5 eth6 #Using ip route2 to do policy based routing. <<EOF bridge name bridge id STP enabled interfaces br0 8000.0008a17aaf17 yes eth0 eth1 br1 8000.000d88687d2c yes...

Anyone know how to get statistics on bonded interfaces? I have a system that does not use eth0-3, rather we have bond0, bond1, bond2. The members of each bond are not eth0-3, rather they are eth6, eth7, etc. I didn't see anything in the man page about forcing sar to collect data on specific network interfaces.

...twork-bridge" "$@" vifnum=3 netdev=eth3 bridge=xenbr3 - dom1 with eth0 in it for testing with an internal machine - dom2 with eth0-eth3 for the router/firewall (Both of them I start manually) My problems: - When I reboot dom0, I get eth4 instead of eth0, eth5 instead of eth1 and eth6 instead of eth2. The bridges are created but no interfaces are attached of course. I then have to put eth4''s mac-address to eth0, etc. and reboot again, to get eth0 - eth3 and the bridges. It never change eth3''s mac-address (where my cable-modem is attached to). What did I...

...:81:37:0e", ATTR{type}=="1", KERNEL=="eth*", > NAME="eth5" > SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", > ATTR{address}=="90:e2:ba:46:ef:30", ATTR{type}=="1", KERNEL=="eth*", > NAME="eth6" > SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", > ATTR{address}=="90:e2:ba:46:ef:31", ATTR{type}=="1", KERNEL=="eth*", > NAME="eth7" > > After reboot it worked fine for all 3 servers, but some time later af...

...k, however it did not work. How do I make a setting to force the connection to these ports for a specific link. Note: I can not use the file as route_rules have neither the source IP (ltsp) nor of disabling (changes from time to time) Here conf #providers linkoi 1 - main eth6 201.89.0.1 track,balance=1 linkrntw 2 - main eth4 189.36.0.2 track,balance=10 #tcrules 2:T 172.16.11.33 0.0.0.0/0 tcp 80,443 2:P 172.16.11.33 0.0.0.0/0 tcp 80,443 2 $FW 0.0.0.0/0 tcp 80,44...

...Router 2 | | --------- Switch -------- | | Firewall WAN LAN Empty Empty Empty Empty Empty Empty | | | | | | | | eth0 eth1 eth2 eth3 eth4 eth5 eth6 eth7 ----------------- ------------------- PCI-X PCI Both routers use HSRP from Cisco to share information about who is alive. This app uses multicast UDP packets to 224.0.0.1 address, port 1985. The problem is, after a while (1 or 2 minutes) the CPU re...