search for: dahdi_spanconfig

Dear Folks, whenever I'm executing following command : dahdi_cfg -vvv I got following error: DAHDI_SPANCONFIG failed on span 1: No such device or address (6) Regards akhilesh -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20140205/f384a2c3/attachment.html>

...0 db (CSU)/0-133 feet (DSX-1) Channel map: Channel 01: Clear channel (Default) (Echo Canceler: none) (Slaves: 01) Channel 02: Clear channel (Default) (Echo Canceler: none) (Slaves: 02) Channel 03: Hardware assisted D-channel (Default) (Echo Canceler: none) (Slaves: 03) 3 channels to configure. DAHDI_SPANCONFIG failed on span 1: No such device or address (6)" I'm in doubt about the "DAHDI_SPANCONFIG failed on span 1: No such device or address (6)". Next, if i execute sudo dmesg as specified by the manual it returns a huge trace: .... .... [ 376.082907] Wrote 0x0 to register 0x1ab but...

...chine with the same dahdi config/kernel: Sarting background readahead: [ OK ] Checking for hardware changes [ OK ] Starting dahdi: Loading DAHDI hardware modules: wct4xxp: [ OK ] wcb4xxp: [ OK ] No hardware timing source found in /proc/dahdi, loading dahdi_dummy Running dahdi_cfg: DAHDI_SPANCONFIG failed on span 1: No such device or address (6) [FAILED] [FAILED] lspci ===== 0:00.0 Non-VGA unclassified device: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz-...

...pbx.ru/pastebin/11 lspci can detect the card: 03:08.0 Communication controller: Digium, Inc. Device 0220 (rev 02) dahdi_hardware also: astpbx ~ # dahdi_hardware pci:0000:03:08.0 wct4xxp+ d161:0220 Wildcard TE220 (4th Gen) astpbx ~ # But dahdi_tool does not show the card and dahdi_cfg gives DAHDI_SPANCONFIG failed on span 1: Invalid argument (22) System info is provided here - http://asteriskpbx.ru/pastebin/12 Please advise. -- Maxim Litnitskiy http://asteriskpbx.ru http://asterisk-support.ru -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipe...

...id argument Wanpipe driver did not load properly Please check /var/log/wanrouter and /var/log/messages for errors Configuring interfaces: w1g1 w1g1: ERROR while getting interface flags: No such device done. /etc/wanpipe/scripts/start: 7: Syntax error: Bad for loop variable DAHDI_SPANCONFIG failed on span 1: No such device or address (6) Dont know why I still keep getting a 'No such device' error even if the device was detected (Sangoma a104de, setup asked to configure/skip the 4 ports) before the error happened. -------------- next part -------------- An HTML attachment was...

I have DAHDI 2.2.1 my system.conf file is : span=1,0,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 loadzone = us defaultzone = us Its telling me: Running dahdi_cfg: DAHDI_SPANCONFIG failed on span 1: Invalid argument (22) [FAILED] What am I missing. Its straight PRI NI2.

...nel 04: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 04) Channel 05: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 05) Channel 06: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 06) Channel 24: D-channel (Default) (Echo Canceler: none) (Slaves: 24) 7 channels to configure. DAHDI_SPANCONFIG failed on span 1: No such device or address (6) Not sure why??? system.conf shows: cat system.conf loadzone=us defaultzone=us span=1,0,0,esf,b8zs bchan=1-6 dchan=24 echocanceller=mg2,1-6 I installed from source. I am running asterisk 11.10.0 libpri is 1.4.14 dahdi modules are loaded with l...

...g2) (Slaves: 20) Channel 21: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 21) Channel 22: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 22) Channel 23: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 23) Channel 24: D-channel (Default) (Slaves: 24) 24 channels to configure. DAHDI_SPANCONFIG failed on span 1: Invalid argument (22) How can i set a working E1. Any examples will welcome..

...FXO Kewlstart (Default) (Echo Canceler: none) (Slaves: 21) Channel 22: FXO Kewlstart (Default) (Echo Canceler: none) (Slaves: 22) Channel 23: FXO Kewlstart (Default) (Echo Canceler: none) (Slaves: 23) Channel 24: FXO Kewlstart (Default) (Echo Canceler: none) (Slaves: 24) 24 channels to configure. DAHDI_SPANCONFIG failed on span 1: Input/output error (5) -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20201022/54a309e9/attachment.html>

...lt) (Slaves: 117) Channel 118: Clear channel (Default) (Slaves: 118) Channel 119: Clear channel (Default) (Slaves: 119) Channel 120: Clear channel (Default) (Slaves: 120) Channel 121: Clear channel (Default) (Slaves: 121) Channel 122: Clear channel (Default) (Slaves: 122) 120 channels to configure. DAHDI_SPANCONFIG failed on span 1: No such device or address (6) dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.0.0 ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 21 (level, low) -> IRQ 21 Detected Tormenta 2 Quad E1/PRA - E400P at 0xdddff000/0xdddfe800 irq 21 Xilinx Chip successfully load...

Hello I just updated the kernel, dahdi-linux and dahdi-tools Im also using now asterisk 1.4.26.1 And im still with a red light (not RED/YELLOW anymore): [root at catumbela ~]# /etc/rc.d/init.d/dahdi status ### Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/ RED 1 PRI CAS RED 2 PRI CAS RED 3 PRI CAS RED 4 PRI