search for: bugdead

Hi, I''m on a HP DL365, amd64, running SLES10sp1, but with kernel and xen of SLES10sp2, therefore using Xen 3.2. The domU shall be a Windows HVM guest. I want use the Qlogic SAN card in a domU. I''m following these instructions: http://www.novell.com/communities/node/2880/assign-dedicated-network-card-or-pci-device-xen-virtual-machine well, there is written that this only

Hi, I some problem setup networking on a opensuse 10.3, x86_64, xen 3.1.0. I have four suse 10.3, x86_64 PVM hosts running on it, they are connected via a bridge to get network. I can connect from external hosts, to the virtual machine, and from the virtual machines to the internet, no problem. But I cannot reach the dom0 from within the domU''s or vice versa. Also the domU''s

Hi, I have started the xen kernel with parameter dom0_mem=300M. xm info | grep total total_memory : 2045 Name ID Mem VCPUs State Time(s) Domain-0 0 300 2 r----- 292.1 FTP 822 1 56.7 LDAP 1 822 1 r----- 541.3 NFS1 822 1 14.8 NFS2 822 1 1.4 For the

Hello everybody, I tried to measure the performance of the available drivers for windows as a HVM guest. I used the gplpv drivers 0.9.11-pre17, the PV drivers from Novell, and the drivers from Citrix XenSource with the XenServer 5. The Novell and gplpv drivers were more or less at the same speed, for both, network and disk performance. The disk performance was about 10MB/s reading and

Hi, do I have a chance to use iax trunking on OpenBSD where there is no zaptel driver or ztdummy available? Do I can use sth. else as timing source? kind regards Sebastian

Hi, I try to get networking running with xen 3.2, but it seems I fail miserably. I am on sles10sp1, with xen 3.2.0, and kernel rpm''s installed from SP2. I configured in /etc/sysconfig/network the NETWORK_LIST: NETWORK_LIST="bridge,0,default,00:DE:AD:BE:EF,192.168.8.13/24,dhcp-off" but an ifconfig xenbr0 still shows the mac address of peth0 fe:ff:ff:ff:ff:ff. Initially, I

Hi, I want to use xen in a cluster, I have qlogic FC cards in the server, and want to use pci passthrough to make it available to the domU nodes. In case of a failover, two or more virtual nodes will run on the same dom0. Will it work to share a physical device on more than one domU node, or will the first one have an exclusive lock on it? kind regards Sebastian

Hi, I copied my root filesystem from one box to a harddisk partition /dev/sda8. I started fdisk /dev/sda and added a bootable flag to partition 8. Then I mounted /dev/sda8, chrooted into it, and ran a grub-install hd0. Then I unmounted it, and tried to start the PVM host, but it ends short after the try to start for the following reason: xm create /etc/xen/vm/VM3 -c Using config file

Hi all, I''m trying to figure out, whether there is a limit of the LUN size for a virtual harddisk used in Xen domU''s. e.g. I setup a domU to use /dev/mapper/large-disk as a disk. Is there a maximum size of the disk that can be used in the virtual machine? As far as I know, I cannot use LUN''s larger than 2 TB in vmware. In case /dev/mapper/large-disk would be a 3 TB

Hi, I want to switch my server into a Xen instance. Right now there are 10 vlans ending up at the server. For each service that the server provides, there is an alias IP address on each of the vlan interfaces to serve the clients. I want ot install xen, and divide the services into 4 virtual nodes. The dom0 machine has three network interfaces, eth0, eth1, eth2. eth0 and eth1 are bonded

Hi, I am on SLES 10, SP1, x86_64, running the distribution rpm's of ocfs: ocfs2console-1.2.3-0.7 ocfs2-tools-1.2.3-0.7 I have a two node ocfs2 cluster configured. One node died (manual reset), and the second started immediately to have problems on accessing the file system for the following reason from the logs: Transport endpoint not connected. a mounted.ocfs2 on the still living

Hi, I am using xen 3.1.0 on opensuse 10.3, for more details see below. When I try to start the third domU, then this will not work, I get the error: Error: Boot loader didn''t return any data! When I shutdown an other one, I can successfully start the machine that failed, see my log below. The xen configuration files are all similar to this one: name="FTP"

Hi all, I am running asterisk 1.2.18, zaptel 1.2.18, libpri 1.2.4. on a suse 10.2, running kernel 2.6.18.2-34-default. The zaptel drivers are loaded on boot via /etc/init.d/zaptel, but Asterisk is unable to start. It ends with the following message: [chan_zap.so] => (Zapata Telephony w/PRI) Jun 13 13:05:41 VERBOSE[3356] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found