Displaying 20 results from an estimated 89 matches for "bge0".
2004 Jul 28
3
Ipfw config
...ny problems, or things i should add. Im not an ipfw expert or
anything. Here is the config.
add 100 allow all from any to any via lo0
add 110 deny log all from any to 127.0.0.0/8
add 120 deny log ip from 127.0.0.0/8 to any
add 00200 check-state
add 00250 deny all from any to any frag in via bge0
add 00260 deny tcp from any to any established in via bge0
###### outbound section ######
## standard http ##
add 00300 allow tcp from any to any 80 out via bge0 setup keep-state
## secure https ##
add 00301 allow tcp from any to any 443 out via bge0 setup keep-state
## dns ##
add 00310 allow t...
2012 Jul 03
3
bge problems in RELENG_9, bge0: watchdog timeout -- resetting
Hi,
I'm having lots of difficulties with BCM5719, which is the default
network card of HP Proliant DL 360 G8 servers. I can get a few ping
replies before I get a couple of these:
bge0: watchdog timeout -- resetting
bge0: watchdog timeout -- resetting
Then everything hangs. Can not log in using ssh.
I'm running: FreeBSD-9.0-RELENG_9-20120701-JPSNAP-amd64
Info about the NIC:
# devinfo...
2009 Mar 16
1
bge0: EEPROM read timed
Hi.
I got this on today's RELENG_6 with Broadcom BCM5722 A0, ASIC rev. 0xa200.
>From dmesg (bge related):
bge0: <Broadcom BCM5722 A0, ASIC rev. 0xa200> mem
0xe8400000-0xe840ffff irq 16 at device 0.0 on pci2
bge0: firmware handshake timed out, found 0x4b657654
bge0: firmware handshake timed out, found 0x4b657654
bge0: EEPROM read timed out
bge0: failed to read EEPROM
device_attach: bge0 attach returned...
2009 Jun 12
6
Duplicate packets when using aggregate datalinks on bge
...henever an aggregate is introduced
into the network configuration. We''ve ruled out switch ports and
physical bge interfaces as problematic. It only manifests when an
aggregation datalink exists in the configuration, regardless of whether
it aggregates multiple physical interfaces (e.g. bge0 and bge1) or a
single physical interface (e.g. bge0).
The duplicates are only generated by the OpenSolaris host. There are no
inbound duplicates. The duplicates always come from the same physical
interface. Tested with ICMP (ping) and TCP (http) connections.
We have numerous servers in produc...
2013 Jan 25
2
bge numbering
Hi,
this server, a Dell R720 has 4 bge on board,
Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000
bge0: APE FW version: NCSI v1.1.7.0
bge0: CHIP ID 0x05720000; ASIC REV 0x5720; CHIP REV 0x57200; PCI-E
miibus0: <MII bus> on bge0
...
I have connected the ethernet to port labeled 0, but it appears
as bge2, how can this be corrected?
thanks,
danny
2003 Jun 04
3
bge drivers does not work for 3COM 3C996-SX / 3C996B-T
...The behaviour is somewhat hard
to diagnose, since there's no panic - just a hard lock.
The 4.8-R machine:
$ uname -a
FreeBSD quadric.dsl.isometry.net 4.8-RELEASE FreeBSD 4.8-RELEASE #0: Sun
Apr 6 19:46:37 UTC 2003
root@quadric.dsl.isometry.net:/usr/obj/usr/src/sys/QUADRIC i386
$ ifconfig bge0
bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=3<rxcsum,txcsum>
inet 192.168.108.1 netmask 0xffffff00 broadcast 192.168.108.255
inet6 fe80::204:76ff:fe3b:6baf%bge0 prefixlen 64 scopeid 0x3
ether 00:04:76:3b:6b:af
me...
2012 Nov 16
2
bge on the new Mac Mini
...the built-in NIC. pciconf -lv on the new mini shows it as
none3 at pci0:1:0:0: class=0x020000 card=0x168614e4 chip=0x168614e4 rev=0x01
hdr=0x00
vendor = 'Broadcom Corporation'
class = network
subclass = ethernet
The previous edition mini (that works) reports
bge0 at pci0:2:0:0: class=0x020000 card=0x16b414e4 chip=0x16b414e4 rev=0x10 hdr=0x00
vendor = 'Broadcom Corporation'
device = 'NetXtreme BCM57765 Gigabit Ethernet PCIe'
class = network
subclass = ethernet
Is there a chance that adding the new card/chip inf...
2009 Jan 06
2
ACPI support?
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hello All,
I have had a problem detecting the network card on my notebook when ACPI
is enabled for a year. The problem still exists in 7.1-RELEASE.
with ACPI:
...
bge0: <Broadcom NetLink Gigabit Ethernet Controller, ASIC rev. 0xb002>
irq 17 at device 0.0 on pci8
bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff).
bge0: couldn't map memory
device_attach: bge0 attach returned 6
...
without ACPI:
...
bge0: <Broadcom NetLink Gigabit Ethernet C...
2006 Sep 29
8
creating a vnic to represent the factory MAC address
...y/default''
address and allows manipulation of the other three via the
MAC_CAPAB_MULTIADDRESS interface.
I''d like to use vnics on this system, as I have Xen guest domains and
will match a vnic with each domain.
Presuming that it''s no longer appropriate to plumb ''bge0'' under IP
(given that I''ll want to also use the physical nic to create vnics)
I''m struggling to figure out how I might create a vnic to represent
this ''slot 0'', in order that I can plumb it under IP.
dme.
--
David Edmondson, Sun Microsystems, http://ww...
2007 Mar 21
16
IP Instances with VLAN''s
Hi,
how can ip instances be used with vlans ? Is that possible ?
I don''t know how to configure this, if I only have one interface (e.g. bge0), and want to
assign e.g. bge1000 to a zone. Any cookbooks available ?
Thanks
Detlef
2009 Nov 04
6
xVM and zones not co-existing happily
...peated these symptoms on another server as well, however in this case I set up the zones first and then installed xVM.
My zone configuration is pretty simple:
create -b
set zonepath=/zones/adriatic
set brand=ipkg
set autoboot=false
set ip-type=shared
add net
set address=192.168.31.29
set physical=bge0
end
Output of ifconfig shows the zone device alias, although it seems to have multiple loopback devices. Is this normal?
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
lo0:1: flags=2001000849<UP,LOOPBACK,RUNNING...
2006 Apr 17
3
IPFW Problems?
Hi,
I have a system with a 4.11 Kernel. Unless I'm doing something very
wrong, there seems to be something odd with ipfw.
Take the following rules:
ipfw add 00280 allow tcp from any to any 22 out via bge0 setup keep-
state
ipfw add 00299 deny log all from any to any out via bge0
ipfw add 0430 allow log tcp from any to me 22 in via bge0 setup limit
src-addr 2
ipfw add 00499 deny log all from any to any in via bge0
In theory, this should allow in SSH and nothing else.
When I install this firewall...
2009 Jun 16
7
objects disappear from dladm after reboot
...d everything was working, then I rebooted my system and everything disappeared from show-vnic, show-flow, and show-prop. When I tried to re-create the objects, dladm said they already existed. While I could not see the objects, I could delete them. Example:
# dladm show-vnic
# dladm create-vnic -l bge0 vphys0
dladm: vnic creation over bge0 failed: object already exists
# dladm show-vnic vphys0
dladm: failed to show vnic ''vphys0'': object not found
# dladm delete-vnic vphys0
# dladm create-vnic -l bge0 vphys0
#
How do I create persistent objects that continue to be visible after...
2008 Jan 30
2
vnic on top of aggr of 2 x 1 Gbit/s NICs
Hi,
Can you tell why my vnic built on top of an aggregation of 2 NICs of 1 Gbit/s doesn''t report a speed of 2 GBit/s ?
[root at nazgul /]# dladm show-dev
bge0 link: up speed: 1000Mb duplex: full
bge1 link: down speed: 0Mb duplex: unknown
bge2 link: down speed: 0Mb duplex: unknown
bge3 link: down speed: 0Mb duplex: unknown
---
Aggregation creation: bge1 & bge2 aggregate...
2020 Apr 01
2
Can't block intrusion
...accepting packets from new tcp or udp packets as matching an old
> connection state object. I would check for the new attempts as coming
> from something that matches the original "connection", even if UDP.
Here is the first four lines from "pfctl -sr":
pass in quick on bge0 from <FRIENDS> to any flags S/SA keep state
block drop in log quick on bge0 from <ENEMIES> to any
block drop in log quick on bge0 from <AUTOBLOCK> to any
block drop out log quick on bge0 from any to <AUTOBLOCK>
Unless pf is broken I can't see how anything besides my &qu...
2003 Sep 29
2
4.9-RC and bge
Recent SUP.
Installed on Dell PowerEdge 4600.
Getting tons of:
Sep 30 12:23:16 zige /kernel: bge0: gigabit link up
Sep 30 12:23:46 zige last message repeated 98 times
Also getting some TCP retransmits. This causes noticable delays in
pretty much everything I do now. Not a problem prior to the SUP.
I was on 4.8-STABLE before.
When pulling/replacing cables, it went into a mode where it would...
2012 Jul 13
2
stable/9 panic Bad tailq NEXT(0xffffffff80e52660->tqh_last) != NULL
...tch range (0xd50e0000-0xd50effff) for rid 18 of
pci0:2:0:1
map[20]: type Prefetchable Memory, range 64, base 0xd50f0000,
size 16, enabled
pcib1: allocated prefetch range (0xd50f0000-0xd50fffff) for rid 20 of
pci0:2:0:1
pcib1: matched entry for 2.0.INTB
pcib1: slot 0 INTB hardwired to IRQ 36
bge0: <Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000> mem
0xd50a0000-0xd50affff,0xd50b0000-0xd50bffff,0xd50c0000-0xd50cffff irq 34
at device 0.0 on pci2
bge0: APE FW version: NCSI v1.0.80.0
bge0: attempting to allocate 1 MSI vectors (8 supported)
msi: routing MSI IRQ 264 to local APIC 0...
2020 Apr 01
0
Can't block intrusion
D'Arcy Cain <darcy at VybeNetworks.com> writes:
> Here is the first four lines from "pfctl -sr":
>
> pass in quick on bge0 from <FRIENDS> to any flags S/SA keep state
> block drop in log quick on bge0 from <ENEMIES> to any
> block drop in log quick on bge0 from <AUTOBLOCK> to any
> block drop out log quick on bge0 from any to <AUTOBLOCK>
agreed that I can't see it.
>> You sa...
2006 Oct 01
1
Crossbow and zones
Howdy,
I just finished reading through the Crossbow presentation:
http://blogs.sun.com/sunay/resource/crossbow.pdf
And have one question. If you create a virtual NIC with dladm:
$ dladm create-vnic -d bge0 -m 0:1:2:3:4:5 -b 10000 1
Can you then add vnic1 directly to the zone? e.g.:
zonecfg -z zone1
zonecfg:zone1> create
zonecfg:zone1> set zonepath=/zones/zone1
zonecfg:zone1> add net
zonecfg:zone1> set physical=vnic1
zonecfg:zone1> set address=192.168.1.100
zonecfg:zone1> end
zonec...
2006 Apr 17
0
IPFW Problems
Hi,
I have a system with a 4.11 Kernel. Unless I'm doing something very
wrong, there seems to be something odd with ipfw.
Take the following rules:
ipfw add 00280 allow tcp from any to any 22 out via bge0 setup keep-
state
ipfw add 00299 deny log all from any to any out via bge0
ipfw add 0430 allow log tcp from any to me 22 in via bge0 setup limit
src-addr 2
ipfw add 00499 deny log all from any to any in via bge0
In theory, this should allow in SSH and nothing else.
When I install this firewall...