search for: b400p

Hi, I've run into a veird problem. I'm using a B400P BRI and an A1200P card with dahdi (2.2.1) driver. The dahdi_scan shows the each moduls and spans, everything seems fine. With dahdi_genconf I made the config, set up the channels in chan_dahdi.conf, but after reboot, the two card changes the order, (originaly the B400P is the first (closer to t...

Hi, I have a B400P BRI card with point-to-point connection (signalling: bri_cpe) with this dmesg: http://pastebin.com/sXrRt1yM When i restart asterisk server, the card cannot connect to the telco, the control led flashes red. If I unplug the cable between the ISDN nt and the card and wait 40 sec, the card can co...

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c ============================================ ?static void hfc_i...

Hi there, i'm using dahdi to manage a B400P openvox BRI card. All works as expected, i would like to know if there ia a way to put the call in REMOTE HOLD, like pressing R button on ISDN phone. This can be done by CAPI using the proper application , It is implemented on DAHDI ? Regards Andrea -- -----------------------------------------...

...a PTP BRI ISDN line, if I have both channels in use and I place a third call from the outside, I'm not getting a busy tone like I should. Instead I get a congestion tone, as if the line was not working/didn't exist. Currently I'm using mISDN 1_1_9.1 and Asterisk 1.4.35 with an OpenVox B400P and I've tried all possible combinations of PTP/PTMP and with or without the termination jumper on the card. I've also tried to make it work since mISDN 1_1_8 and Asterisk 1.4.18. This is the message I get in Asterisk when the third call tries to come in: P[ 4] channel with stid:10020400...

Roberto Thanks. Panasonic KX-TD1232 system ISDN interface use DDK plug, not same cord you are using for openvox B400P card. Each port could be configured as CO or extension port as Point-Point or PTMP in both mode. Regarding to dial timeout these it becomes from ISDN dial mode overlap or En-bloc, by the way you can close dialling number by using # key. Best regards Mc GRATH Ricardo E-Mail mcgrathr at mail2web...

...e works quite fine after roughly a minute once connected. The PBX can be seen at http://www.telephone-engineer.com/downloads/versatility/versatility-installation.pdf Putting the pri span in debug mode I can see the following log continuously scrolling and the PBX never synchronize with the openvox B400P card: PRI Span: 1 TEI=0 MDL-ERROR (G): T200 expired N200 times sending SABME in state 5(Awaiting establishment) PRI Span: 1 Changing from state 5(Awaiting establishment) to 4(TEI assigned) PRI Span: 1 TEI=0 DL event: Q931_DL_EVENT_DL_RELEASE_IND(3) PRI Span: 1 SAPI/TEI=0/0 Kick starting link PRI S...

Hello I'd like to build myself an Asterisk server for SOHO use. Intel's D201GLY2 motherboard (http://tinyurl.com/ddarzp) looks like a very good deal, but I'm concerned about two things: 1. Will an A400P (from OpenVox, but supposed to be Digium-compatible http://tinyurl.com/ck6nfu) fit with a PCI riser, or will the CPU heatsink/fan be in the way? I downloaded the PDF from

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and port 2 as NT mode ,port 3 and port 4 as TE mode. ********************system.conf*************************** # Autogenerated by /usr/sbin/dahdi_genconf on Wed Jun 16 22:49:10 2010 # If you edit this fil...

Hello Does anyone have any experience with configuring BT (British Telecom) ISDN2e lines to work with Patton SmartNodes - and then Asterisk? I have a Patton SmartNode 4638, which is now connected to 3 x ISDN2e lines - and in turn connected to our internal LAN. I'm having huge issues configuring the SmartNode to successfully "see" the ISDN channels - and to be honest, I'm

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment********************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ******************************************************************** In my case , I set prot 1 and port 2 as NT mode ,port 3 and port 4 as TE mode. ********************system.conf************************************* # Autogenerated by /usr/sbin/dahdi_genconf on Wed Jun 16 22:49:10 2010 # If you e...

Hello all What I'm looking for is some plain speaking advice on ISDN. Currently using 4 analog lines connecting via a four port TDM400P FXO card. We need to physically move our installations, and on requesting the analog lines be moved - our telco (BT) is suggesting we replace our analog lines with ISDN2. We would have 3 x ISDN2 connections, giving us six voice channels. They've