search for: a101u

I have a very annoying problem that we hear on our end, but the other party doesn't hear. There are random beeps and echo type noises that occur. They are present during voicemails, and present on my end during calls. Is anyone experiencing the same deal? I have asked this a number of ways on the list, and never get a response... Thank you. Sean Garland Mount Shasta, CA

...ing a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info | ------------------------------- 1 . AFT-A101u : SLOT=1 : BUS=1 : IRQ=209 : CPU=A : PORT=PRI Card Cnt: S508=0 S514X=0 S518=0 A101-2=1 A104=0 A300=0 So I know the card is there OK. My /etc/zaptel.conf looks like: span=1,1,0,esf,b8zs loadzone = us defaultzone=us fxsls=1-12 I am only trying to get half to load for now to make it simple....

Even though they make the cards and advertise that they support data modes, digium won't support data mode on the $500 card they sold to me, so I must turn to the list. Has anyone configured a T100P to use a T1 strictly as bandwidth? Is there a HOWTO somewhere? Wiki has nothing I could find. I've got plently of public IPs I can assign to it but don't know how. Thanks, Matthew -----

...e is up. I had a meeting with upper management yesterday, and they would like some assurance that other companies are running Asterisk with success. We are a relatively small company, with about 70 total extensions. I would be purchasing a Dell Poweredge 2850 Server and most likely a Sangoma A101U. The phone service would be provided by a ISDN PRI from SBC, with Caller ID and DID. The phones we are looking at are the Uniden UIP-200, and the Cisco 7940G on the high end. I've become fairly familiar with Asterisk, and i'm pretty confident that I should be able to squash most of t...

We just installed a box into a Melbourne site with a Sangoma A101U, it is running the latest Wanpipe drivers and has Asterisk on it that someone had compiled manually from source. This initially worked fine but for the sake of consitancy we removed the existing asterisk and used emerge to install it. During this time the box was off of the e1 for about 8 hou...

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

Here is the situation: A T1 router going into an office which then plugs into the firewall box then into the switch. None of these devices support QOS.. Is there some sort of box/device that I can place between the T1 router and the firewall box which will allow me to prioritize voice traffic on this link? I can't change the T1 router to something that supports QOS because it has

Good day all Is there someone that's got asterisk working well with a A101/E1 card Apparently they don't have RBS support? Please advice Thanks Altus

Has anyone attempted to use FreePBX for a business in production mode? Initial take is there are lots of things scripted but a lot of limitations in terms of supporting basic business functions. Inability (or lack of flexibility) is handling multiple incoming pstn lines, dialplan limitations, poor/no documentation, etc, to mention a few. Maybe its just me, but it appears its no where near

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound