search for: 1600sc

Hi all, Let me start off with a little back ground. I am running right now RH9 fully updated on a Dell PowerEdge 1600SC with 512megs of Ram, 18G SCSI HD. I run this at home so this is no critical server, unless you ask my girls when I have it down, I have been debating on upgrading to Fedora until I started looking at CentOS. I have download the ISO and burned them with X-CD-Roast. Here is my question: I trie...

Alright, I've come across a really strange issue and I've been banging my head trying to figure it out. I have 3 machines. 1 Dell Dimension 4100, Pentium 3. 1 Dell 400SC, Pentium 4. 1 Dell 1600SC, Xeon. I run mpg123 0.59r on each machine. Using RH9 with a 2.4.20-8 kernel, each machine plays MoH flawlessly. As RH9 gets older and older, however, the need to upgrade arose. So I upgraded each machine to CentOS 4.3, with various 2.6 kernels ranging from 2.6.22 to 2.6.34 (yes, with the spinlo...

Hi All. Yesterday I was installing Centos 5.5 to my web server, and it looks like the main hard drive has gone AWOL. Fedora 12 put the file system into r/o mode. The drive is an Hitachi, still under warranty. There are bad sectors on it, and running the Hitachi DFT tool confirms this. Also I cannot repair the bad sectors. Would this be caused by a faulty I/O chip, or is it safe to say

Hello, I''m frustrated, and confused. Someone send me a light bulb. I have a UPS attached to the only serial port on a Dell PowerEdge 1600SC. When I boot the system with the xen kernel, ttyS0 NEVER gets created. I though that perhaps the default xen kernel config was the problem, so I configured a new one, based on the kernel config from the RHEL 4 (U3) kernel (which is running in dom0). I built the new kernel, installed it, and amaz...

...o anomaly rather than a delay. When there are no active zap channels, the issue does not exist. The disk controller and the Zap card do not share an interrupt (The zap card has its own interrupt - not shared with anything). We're running a version of CVS HEAD from 04/09/05 on a Dell PE 1600SC with a U320 SCSI, Raid 1 (LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI), with a TE410P connected to a PRI. Has anybody experienced anything similar? Anybody have a clue as to what's going on? Zttool does show 15 IRQ misses, but that is over the course of the...

what is a typical server / processor / memory configuration for approx 50 user install? phone -> asterisk -> pri thanks Phil.

...g or are PDCs with tdbsam rare (or is that totally unrelated to the problems I'm experiencing). I've also tried using a Samba PDC config from the HOWTO rather than my own hand-crafted one (see below for both). Samba version is 3.0.23d running on 2.6.17-2-686 Debian etch on Dell Poweredge 1600sc with an Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02). I have a djbdns dhcp server on the network serving which references the samba server as a wins server. Thanks, -stephen Original PDC config [global] workgroup = XXXXX netbios name = XXXX server string = %h server...

...e in the early 90's), and I'll try to not go into news.admin mode here in the future. Now, the question. I have a few ideas about how to do this, but am not sure of the ideal way of doing it. It has to be a pretty common thing to do, so I'll ask it here. I have a server (Dell PE 1600SC) with two SCSI host adapters: a U320 LSI/MPT for internal drives only, and an Adaptec 39160 with two internal and two external U160 channels. I have set up a software RAID config with LVM2 on top (CentOS 4) with four 36GB 15K RPM Ultra 3 drives. The internal drives are set up with /dev/sda an...

Are there any easy to use snmp(mainly temperature monitoring) tools around for Centos -4? This is on a Dell sc420 server. -- Computer House Calls, Networks, Security, Web Design: http://www.emmanuelcomputerconsulting.com What businesses are in Brunswick, Maryland? Check Brunswick First! http://www.checkbrunswickfirst.com My "Foundation" verse: Isa 54:17 No weapon that is formed

Hi all, I have this project that requires me to use 8 PSTN lines and possible more. I was thinking 2 TDM cards with FXO modules. The I got to read the "Qs about FXO/FXS cards" thread and that scared me. Can anybody recommend anything that is known to work ok with no mysterious problems? I was thinking OpenSwitch12 cards. What do you guys think? Any help is appreciated. Regards, Hadi

Dear Sirs. It seems to me a never ending story. We run a box with a TYAN Thunder 2500 Dual SMP mainboard, 2GB ECC Tyan certified memory, AMI Enterprise 1600 RAID adapter and additional Intel 1000/Pro server type (64 bit) GBit LAN NIC. With FreeBSD 4.8 this was stable, but to achive this state was really hard! It is a story similar to that what happend when we changed towards FreeBSD