Kari Lempiäinen
2023-Jun-11 18:32 UTC
[Nut-upsuser] Upssched 100% CPU after updating Debian 12
Hi,
I have been running nut successfully for a long time with my Debian 11 server. I
upgraded my server to Debian 12 today, which upgraded nut also from 2.7.4-13 to
2.8.0-7. I noticed that after upgrade there was a upssched process running and
taking 100% cpu time.
I checked if there were any changes to configuration file formats with nut
upgrade and only differences I noticed were a terminology change from
master/slave to primary/secondary in upsd.users and upsmon.conf, and dummy mode
change for the dummy-ups. I didn?t expect these being the culprit, but I made
the changes to my configuration. No change, after five minutes of starting nut,
upssched will be running with 100% cpu usage.
Any ideas what could be causing this? Here is my configuration and in the end
are some log snippets:
---------------------------------------------------
heartbeat.conf
# heartbeat.conf -- 10 minute heartbeat
ups.status: OL
TIMER 300
ups.status: OB
TIMER 300
---------------------------------------------------
hosts.conf
MONITOR eaton5s at localhost "Eaton 5S 700"
---------------------------------------------------
nut.conf
MODE=netserver
---------------------------------------------------
ups.conf
maxretry = 3
[eaton5s]
driver = usbhid-ups
port = auto
desc = "Eaton 5S 700i UPS"
vendorid = "0463"
productid = "FFFF"
pollinterval = 15
[heartbeat]
driver = dummy-ups
mode=dummy-loop
port = heartbeat.conf
desc = "Watch over NUT"
---------------------------------------------------
upsd.conf
LISTEN 0.0.0.0 3493
---------------------------------------------------
upsmon.conf
RUN_AS_USER root
MONITOR eaton5s at localhost 1 upsmaster xxx primary
MONITOR heartbeat at localhost 0 upsmaster xxx primary
MINSUPPLIES 1
NOTIFYCMD /sbin/upssched
SHUTDOWNCMD "/sbin/shutdown -h +0"
POLLFREQ 5
POLLFREQALERT 5
HOSTSYNC 15
DEADTIME 15
POWERDOWNFLAG /etc/killpower
RBWARNTIME 43200
NOCOMMWARNTIME 300
FINALDELAY 5
NOTIFYMSG ONLINE "UPS %s: On line power."
NOTIFYMSG ONBATT "UPS %s: On battery."
NOTIFYMSG LOWBATT "UPS %s: Battery is low."
NOTIFYMSG REPLBATT "UPS %s: Battery needs to be replaced."
NOTIFYMSG FSD "UPS %s: Forced shutdown in progress."
NOTIFYMSG SHUTDOWN "Auto logout and shutdown proceeding."
NOTIFYMSG COMMOK "UPS %s: Communications (re-)established."
NOTIFYMSG COMMBAD "UPS %s: Communications lost."
NOTIFYMSG NOCOMM "UPS %s: Not available."
NOTIFYMSG NOPARENT "upsmon parent dead, shutdown impossible."
NOTIFYFLAG ONLINE EXEC
NOTIFYFLAG ONBATT EXEC
NOTIFYFLAG LOWBATT SYSLOG+WALL
NOTIFYFLAG REPLBATT SYSLOG+WALL
NOTIFYFLAG FSD SYSLOG+WALL
NOTIFYFLAG SHUTDOWN SYSLOG+WALL
NOTIFYFLAG COMMOK SYSLOG+WALL
NOTIFYFLAG COMMBAD SYSLOG+WALL
NOTIFYFLAG NOCOMM SYSLOG+WALL
NOTIFYFLAG NOPARENT SYSLOG+WALL
---------------------------------------------------
upssched.conf
CMDSCRIPT /etc/nut/upssched-cmd
PIPEFN /var/run/nut/upssched.pipe
LOCKFN /var/run/nut/upssched.lock
AT ONBATT eaton5s at localhost EXECUTE onbatt
AT ONBATT eaton5s at localhost START-TIMER beeperoff 15
AT ONLINE eaton5s at localhost EXECUTE online
AT ONLINE eaton5s at localhost CANCEL-TIMER beeperoff
AT ONBATT eaton5s at localhost START-TIMER shutdown-ws2019 300
AT ONLINE eaton5s at localhost CANCEL-TIMER shutdown-ws2019
AT ONBATT heartbeat at localhost CANCEL-TIMER heartbeat-failure-timer
AT ONBATT heartbeat at localhost START-TIMER heartbeat-failure-timer 660
---------------------------------------------------
upsd.users
[upsmaster]
password = xxx
upsmon primary
actions = set
actions = fsd
instcmds = all
[upsslave]
password = xxx
upsmon secondary
---------------------------------------------------
upssched-cmd
#! /bin/bash
UPS="eaton5s"
UPS_USERNAME="upsmaster"
UPS_PASSWORD="xxx"
EMAIL_TO=xxx at xxx.xxx<mailto:xxx at xxx.xxx>
EMAIL_FROM=xxx at xxx.xxx<mailto:xxx at xxx.xxx>
STATUS=`upsc $UPS ups.status 2>&1 | grep -v '^Init SSL'`
CHARGE=`upsc $UPS battery.charge 2>&1 | grep -v '^Init SSL'`
CHMSG="[$STATUS]:$CHARGE%"
MSG="dummy message - $1"
case $1 in
online) MSG="$UPS, $CHMSG - On line power - power supply had been
restored." ;;
onbatt) MSG="$UPS, $CHMSG - On battery - power failure - save your
work!" ;;
lowbatt) MSG="$UPS, $CHMSG - Battery is low - shutdown now!"
;;
beeperoff)
logger -i -t upsshed-cmd "Turning off Beeper"
STATUS=`upsc ${UPS} ups.beeper.status 2>&1 | grep -v
'^Init SSL'`
if [[ "${STATUS}" == "enabled" ]] ; then
upscmd -u ${UPS_USERNAME} -p ${UPS_PASSWORD} ${UPS}
beeper.toggle
fi
;;
shutdown-ws2019)
MSG="$UPS, $CHMSG - Stopping WS2019"
logger -i -t upsshed-cmd "Stopping WS2019"
setsid /usr/local/bin/shutdown-ws2019 &
;;
upsgone)
logger -i -t upssched-cmd "The UPS has been gone for
awhile"
;;
heartbeat-failure-timer)
MSG="NUT heart beat fails. $CHMSG"
# Email
MSG1="Hello, upssched-cmd reports NUT heartbeat has
failed."
MSG2="Current status: $CHMSG \n\n$0 $1"
MSG3="\n\n$( ps -elf | grep -E 'ups[dms]|nut'
)"
echo -e "$MSG1 $MSG2 $MSG3" | /usr/bin/mail -r
"$EMAIL_FROM" \
-s "NUT heart beat fails. Currently $CHMSG"
"$EMAIL_TO" ;;
*)
logger -i -t upssched-cmd "Unrecognized command: $1"
;;
esac
logger -i -t upssched-cmd $MSG
wall "$MSG"
---------------------------------------------------
---------------------------------------------------
This is normal ups activity in daemon log from the previous version:
Jun 10 23:10:50 fricka upssched[16007]: Cancelling timer:
heartbeat-failure-timer
Jun 10 23:10:50 fricka upssched[16007]: New timer: heartbeat-failure-timer (660
seconds)
Jun 10 23:20:50 fricka upssched[16007]: Cancelling timer:
heartbeat-failure-timer
Jun 10 23:20:50 fricka upssched[16007]: New timer: heartbeat-failure-timer (660
seconds)
Jun 10 23:30:55 fricka upssched[16007]: Cancelling timer:
heartbeat-failure-timer
Jun 10 23:30:55 fricka upssched[16007]: New timer: heartbeat-failure-timer (660
seconds)
Jun 10 23:40:55 fricka upssched[16007]: Cancelling timer:
heartbeat-failure-timer
Jun 10 23:40:55 fricka upssched[16007]: New timer: heartbeat-failure-timer (660
seconds)
Jun 10 23:50:55 fricka upssched[16007]: Cancelling timer:
heartbeat-failure-timer
Jun 10 23:50:55 fricka upssched[16007]: New timer: heartbeat-failure-timer (660
seconds)
---------------------------------------------------
This is daemon log from the new version, first two lines are the last lines of
the startup messages. One same upssched process (124835) running with 100% cpu
from 21:07:
Jun 11 21:02:40 fricka dummy-ups[121803]: sock_connect: enabling asynchronous
mode (auto)
Jun 11 21:02:41 fricka usbhid-ups[121820]: sock_connect: enabling asynchronous
mode (auto)
Jun 11 21:07:40 fricka upssched[124835]: Timer daemon started
Jun 11 21:07:40 fricka upssched[124835]: New timer: heartbeat-failure-timer (660
seconds)
Jun 11 21:07:40 fricka nut-monitor[124832]: Network UPS Tools upsmon 2.8.0
Jun 11 21:12:40 fricka nut-monitor[128005]: Network UPS Tools upsmon 2.8.0
Jun 11 21:17:40 fricka upssched[124835]: Cancelling timer:
heartbeat-failure-timer
Jun 11 21:17:40 fricka upssched[124835]: New timer: heartbeat-failure-timer (660
seconds)
Jun 11 21:17:40 fricka nut-monitor[131233]: Network UPS Tools upsmon 2.8.0
Jun 11 21:22:45 fricka nut-monitor[134330]: Network UPS Tools upsmon 2.8.0
Jun 11 21:27:45 fricka upssched[124835]: Cancelling timer:
heartbeat-failure-timer
Jun 11 21:27:45 fricka upssched[124835]: New timer: heartbeat-failure-timer (660
seconds)
Jun 11 21:27:45 fricka nut-monitor[137838]: Network UPS Tools upsmon 2.8.0
---------------------------------------------------
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://alioth-lists.debian.net/pipermail/nut-upsuser/attachments/20230611/b66860d3/attachment-0001.htm>
Hello,
Thank you for the report and I don't recall any similar issues.
Unfortunately, upssched did not have any "native" enablement of
debug
verbosity in 2.8.0 and older releases (some added with
https://github.com/networkupstools/nut/pull/1864 recently), so maybe the
best way to get more info at the moment would be to watch syscalls made
when it begins to hog CPU and make educated guesses from there, e.g.:
# strace -f -ttt -T -p "`ps -ef | grep -w upssched | grep -v grep | awk
'{print $2}'`"
I suppose when hogging the CPU it has some reason to quickly interrupt
its processing loop - perhaps a lack of some file (socket?) it waits on,
etc.
Hope this helps,
Jim Klimov
On Mon, Jun 12, 2023, 14:59 Kari Lempi?inen <kari.lempiainen at
summerday.net>
wrote:
> Hi,
>
>
>
> I have been running nut successfully for a long time with my Debian 11
> server. I upgraded my server to Debian 12 today, which upgraded nut also
> from 2.7.4-13 to 2.8.0-7. I noticed that after upgrade there was a upssched
> process running and taking 100% cpu time.
>
>
>
> I checked if there were any changes to configuration file formats with nut
> upgrade and only differences I noticed were a terminology change from
> master/slave to primary/secondary in upsd.users and upsmon.conf, and dummy
> mode change for the dummy-ups. I didn?t expect these being the culprit, but
> I made the changes to my configuration. No change, after five minutes of
> starting nut, upssched will be running with 100% cpu usage.
>
>
>
> Any ideas what could be causing this? Here is my configuration and in the
> end are some log snippets:
>
> ---------------------------------------------------
>
> heartbeat.conf
>
>
>
> # heartbeat.conf -- 10 minute heartbeat
>
> ups.status: OL
>
> TIMER 300
>
> ups.status: OB
>
> TIMER 300
>
> ---------------------------------------------------
>
> hosts.conf
>
>
>
> MONITOR eaton5s at localhost "Eaton 5S 700"
>
> ---------------------------------------------------
>
> nut.conf
>
>
>
> MODE=netserver
>
> ---------------------------------------------------
>
> ups.conf
>
>
>
> maxretry = 3
>
> [eaton5s]
>
> driver = usbhid-ups
>
> port = auto
>
> desc = "Eaton 5S 700i UPS"
>
> vendorid = "0463"
>
> productid = "FFFF"
>
> pollinterval = 15
>
> [heartbeat]
>
> driver = dummy-ups
>
> mode=dummy-loop
>
> port = heartbeat.conf
>
> desc = "Watch over NUT"
>
> ---------------------------------------------------
>
> upsd.conf
>
>
>
> LISTEN 0.0.0.0 3493
>
> ---------------------------------------------------
>
> upsmon.conf
>
>
>
> RUN_AS_USER root
>
> MONITOR eaton5s at localhost 1 upsmaster xxx primary
>
> MONITOR heartbeat at localhost 0 upsmaster xxx primary
>
> MINSUPPLIES 1
>
> NOTIFYCMD /sbin/upssched
>
> SHUTDOWNCMD "/sbin/shutdown -h +0"
>
> POLLFREQ 5
>
> POLLFREQALERT 5
>
> HOSTSYNC 15
>
> DEADTIME 15
>
> POWERDOWNFLAG /etc/killpower
>
> RBWARNTIME 43200
>
> NOCOMMWARNTIME 300
>
> FINALDELAY 5
>
> NOTIFYMSG ONLINE "UPS %s: On line power."
>
> NOTIFYMSG ONBATT "UPS %s: On battery."
>
> NOTIFYMSG LOWBATT "UPS %s: Battery is low."
>
> NOTIFYMSG REPLBATT "UPS %s: Battery needs to be replaced."
>
> NOTIFYMSG FSD "UPS %s: Forced shutdown in progress."
>
> NOTIFYMSG SHUTDOWN "Auto logout and shutdown proceeding."
>
> NOTIFYMSG COMMOK "UPS %s: Communications (re-)established."
>
> NOTIFYMSG COMMBAD "UPS %s: Communications lost."
>
> NOTIFYMSG NOCOMM "UPS %s: Not available."
>
> NOTIFYMSG NOPARENT "upsmon parent dead, shutdown impossible."
>
> NOTIFYFLAG ONLINE EXEC
>
> NOTIFYFLAG ONBATT EXEC
>
> NOTIFYFLAG LOWBATT SYSLOG+WALL
>
> NOTIFYFLAG REPLBATT SYSLOG+WALL
>
> NOTIFYFLAG FSD SYSLOG+WALL
>
> NOTIFYFLAG SHUTDOWN SYSLOG+WALL
>
> NOTIFYFLAG COMMOK SYSLOG+WALL
>
> NOTIFYFLAG COMMBAD SYSLOG+WALL
>
> NOTIFYFLAG NOCOMM SYSLOG+WALL
>
> NOTIFYFLAG NOPARENT SYSLOG+WALL
>
> ---------------------------------------------------
>
> upssched.conf
>
>
>
> CMDSCRIPT /etc/nut/upssched-cmd
>
> PIPEFN /var/run/nut/upssched.pipe
>
> LOCKFN /var/run/nut/upssched.lock
>
>
>
> AT ONBATT eaton5s at localhost EXECUTE onbatt
>
> AT ONBATT eaton5s at localhost START-TIMER beeperoff 15
>
> AT ONLINE eaton5s at localhost EXECUTE online
>
> AT ONLINE eaton5s at localhost CANCEL-TIMER beeperoff
>
> AT ONBATT eaton5s at localhost START-TIMER shutdown-ws2019 300
>
> AT ONLINE eaton5s at localhost CANCEL-TIMER shutdown-ws2019
>
> AT ONBATT heartbeat at localhost CANCEL-TIMER heartbeat-failure-timer
>
> AT ONBATT heartbeat at localhost START-TIMER heartbeat-failure-timer 660
>
> ---------------------------------------------------
>
> upsd.users
>
>
>
> [upsmaster]
>
> password = xxx
>
> upsmon primary
>
> actions = set
>
> actions = fsd
>
> instcmds = all
>
>
>
> [upsslave]
>
> password = xxx
>
> upsmon secondary
>
> ---------------------------------------------------
>
> upssched-cmd
>
>
>
> #! /bin/bash
>
>
>
> UPS="eaton5s"
>
> UPS_USERNAME="upsmaster"
>
> UPS_PASSWORD="xxx"
>
> EMAIL_TO=xxx at xxx.xxx
>
> EMAIL_FROM=xxx at xxx.xxx
>
> STATUS=`upsc $UPS ups.status 2>&1 | grep -v '^Init SSL'`
>
> CHARGE=`upsc $UPS battery.charge 2>&1 | grep -v '^Init SSL'`
>
> CHMSG="[$STATUS]:$CHARGE%"
>
> MSG="dummy message - $1"
>
>
>
> case $1 in
>
> online) MSG="$UPS, $CHMSG - On line power - power supply had
been
> restored." ;;
>
> onbatt) MSG="$UPS, $CHMSG - On battery - power failure - save
your
> work!" ;;
>
> lowbatt) MSG="$UPS, $CHMSG - Battery is low - shutdown
now!" ;;
>
> beeperoff)
>
> logger -i -t upsshed-cmd "Turning off Beeper"
>
> STATUS=`upsc ${UPS} ups.beeper.status 2>&1 | grep -v
> '^Init SSL'`
>
> if [[ "${STATUS}" == "enabled" ]] ;
then
>
> upscmd -u ${UPS_USERNAME} -p ${UPS_PASSWORD}
> ${UPS} beeper.toggle
>
> fi
>
> ;;
>
> shutdown-ws2019)
>
> MSG="$UPS, $CHMSG - Stopping WS2019"
>
> logger -i -t upsshed-cmd "Stopping WS2019"
>
> setsid /usr/local/bin/shutdown-ws2019 &
>
> ;;
>
> upsgone)
>
> logger -i -t upssched-cmd "The UPS has been gone for
> awhile"
>
> ;;
>
> heartbeat-failure-timer)
>
> MSG="NUT heart beat fails. $CHMSG"
>
> # Email
>
> MSG1="Hello, upssched-cmd reports NUT heartbeat has
> failed."
>
> MSG2="Current status: $CHMSG \n\n$0 $1"
>
> MSG3="\n\n$( ps -elf | grep -E 'ups[dms]|nut'
)"
>
> echo -e "$MSG1 $MSG2 $MSG3" | /usr/bin/mail -r
> "$EMAIL_FROM" \
>
> -s "NUT heart beat fails. Currently $CHMSG"
"$EMAIL_TO" ;;
>
>
>
> *)
>
> logger -i -t upssched-cmd "Unrecognized command:
$1"
>
> ;;
>
> esac
>
>
>
> logger -i -t upssched-cmd $MSG
>
> wall "$MSG"
>
> ---------------------------------------------------
>
>
>
>
>
> ---------------------------------------------------
>
> This is normal ups activity in daemon log from the previous version:
>
>
>
> Jun 10 23:10:50 fricka upssched[16007]: Cancelling timer:
> heartbeat-failure-timer
>
> Jun 10 23:10:50 fricka upssched[16007]: New timer: heartbeat-failure-timer
> (660 seconds)
>
> Jun 10 23:20:50 fricka upssched[16007]: Cancelling timer:
> heartbeat-failure-timer
>
> Jun 10 23:20:50 fricka upssched[16007]: New timer: heartbeat-failure-timer
> (660 seconds)
>
> Jun 10 23:30:55 fricka upssched[16007]: Cancelling timer:
> heartbeat-failure-timer
>
> Jun 10 23:30:55 fricka upssched[16007]: New timer: heartbeat-failure-timer
> (660 seconds)
>
> Jun 10 23:40:55 fricka upssched[16007]: Cancelling timer:
> heartbeat-failure-timer
>
> Jun 10 23:40:55 fricka upssched[16007]: New timer: heartbeat-failure-timer
> (660 seconds)
>
> Jun 10 23:50:55 fricka upssched[16007]: Cancelling timer:
> heartbeat-failure-timer
>
> Jun 10 23:50:55 fricka upssched[16007]: New timer: heartbeat-failure-timer
> (660 seconds)
>
> ---------------------------------------------------
>
> This is daemon log from the new version, first two lines are the last
> lines of the startup messages. One same upssched process (124835) running
> with 100% cpu from 21:07:
>
>
>
> Jun 11 21:02:40 fricka dummy-ups[121803]: sock_connect: enabling
> asynchronous mode (auto)
>
> Jun 11 21:02:41 fricka usbhid-ups[121820]: sock_connect: enabling
> asynchronous mode (auto)
>
> Jun 11 21:07:40 fricka upssched[124835]: Timer daemon started
>
> Jun 11 21:07:40 fricka upssched[124835]: New timer:
> heartbeat-failure-timer (660 seconds)
>
> Jun 11 21:07:40 fricka nut-monitor[124832]: Network UPS Tools upsmon 2.8.0
>
> Jun 11 21:12:40 fricka nut-monitor[128005]: Network UPS Tools upsmon 2.8.0
>
> Jun 11 21:17:40 fricka upssched[124835]: Cancelling timer:
> heartbeat-failure-timer
>
> Jun 11 21:17:40 fricka upssched[124835]: New timer:
> heartbeat-failure-timer (660 seconds)
>
> Jun 11 21:17:40 fricka nut-monitor[131233]: Network UPS Tools upsmon 2.8.0
>
> Jun 11 21:22:45 fricka nut-monitor[134330]: Network UPS Tools upsmon 2.8.0
>
> Jun 11 21:27:45 fricka upssched[124835]: Cancelling timer:
> heartbeat-failure-timer
>
> Jun 11 21:27:45 fricka upssched[124835]: New timer:
> heartbeat-failure-timer (660 seconds)
>
> Jun 11 21:27:45 fricka nut-monitor[137838]: Network UPS Tools upsmon 2.8.0
>
>
>
>
>
> ---------------------------------------------------
>
>
> _______________________________________________
> Nut-upsuser mailing list
> Nut-upsuser at alioth-lists.debian.net
> https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsuser
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://alioth-lists.debian.net/pipermail/nut-upsuser/attachments/20230612/ff16d3f9/attachment-0001.htm>