Richard Achmatowicz
2019-Nov-29 17:15 UTC
Re: [libvirt-users] What's the best way to make use of VLAN interfaces with VMs?
Hi Laine What you have suggested sounds eminently reasonable. Thanks for your advice. I'm going to give it a shot and report back. Richard On 11/27/19 1:38 PM, Laine Stump wrote:> On 11/26/19 11:07 PM, Richard Achmatowicz wrote: >> Hello >> >> I have a problem with attaching VMs to a VLAN interface. >> >> Here is my setup: I have several physical hosts connected by a >> physical switch. Each host has two NICs leading to the switch, which >> have been combined into a team, team0. Each host a has a bridge br1, >> which has team0 as a slave. So communication between hosts is based >> on the IP address of bridge br1 on each host. >> >> Up until recently, using libvirt and KVM, I was creating VMs which >> had one interface attached the default virtual network and one >> interface attached to the bridge: >> >> virt-install ... --network network=default --network bridge=br1 ... >> >> I would then statically assign an IP address to the bridge interface >> on the guest when installing the OS. >> >> A few days ago, a VLAN was introduced to split up the network. I >> created a new VLAN interface br1.600 on each of the hosts. My initial >> attempt was to do try this: >> >> virt-install ... --network network=default --network bridge=br1.600 ... >> >> which did not work. It then dawned on me that a VLAN interface and a >> bridge aren't treated the same. So I started to look for ways to >> allow my VMs to bind to this new interface. >> >> This would seem to be a common situation. What is the best way to >> work around this? >> >> Both the host bridge and the host VLAN interface already have their >> assigned IP addresses and appear like this in libvirt: >> >> [root@clusterdev01 ]# ifconfig >> br1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 >> inet 192.168.0.110 netmask 255.255.255.0 broadcast >> 192.168.0.255 >> inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid >> 0x20<link> >> ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) >> RX packets 833772 bytes 2976958254 (2.7 GiB) >> RX errors 0 dropped 0 overruns 0 frame 0 >> TX packets 331237 bytes 23335124 (22.2 MiB) >> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 >> >> br1.600: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 >> inet 192.168.1.110 netmask 255.255.255.0 broadcast >> 192.168.1.255 >> inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid >> 0x20<link> >> ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) >> RX packets 189315 bytes 9465744 (9.0 MiB) >> RX errors 0 dropped 0 overruns 0 frame 0 >> TX packets 302 bytes 30522 (29.8 KiB) >> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 >> >> [root@clusterdev01]# virsh iface-list --all >> Name State MAC Address >> --------------------------------------------------- >> br1 active 1c:98:ec:1b:27:6d >> br1.600 active 1c:98:ec:1b:27:6d >> >> [root@clusterdev01 sysadmin]# virsh iface-dumpxml br1.600 >> <interface type='vlan' name='br1.600'> >> <protocol family='ipv4'> >> <ip address='192.168.1.110' prefix='24'/> >> </protocol> >> <protocol family='ipv6'> >> <ip address='fe80::1e98:ecff:fe1b:276d' prefix='64'/> >> </protocol> >> <link state='up'/> >> <vlan tag='600'> >> <interface name='br1'/> >> </vlan> >> </interface> >> >> I tried following some suggestions which wrapped the vlan interface >> in a bridge interface, but in ended up trashing the br1.600 interface >> which was originally defined on the host. >> >> Is there a failsafe way to deal with such a situation? Am I doing >> something completely wrong here? In would like br1.600 to behave like >> br1 ..... >> >> Any suggestions or advice greatly appreciated. > > > I guess what you need is for all the traffic from your guests to go > out on the physical network tagged with vlan id 600, and you want that > to be transparent to the guests, right? > > The simplest way to handle this is to create a vlan interface off of > the ethernet that you have attached to br1 (not br1 itself), so it > would be named something like "eth0.600", and then create a new bridge > (call it, say "br600") and attach eth0.600 to br600. Then your guests > would be created with "--network bridge=br600" > > (Note that Linux host bridges do now support vlan tagging (and maybe > even trunking) at the port level, but libvirt hasn't added support for > it. (in other words, "Patches Welcome!" :-)) >
Richard Achmatowicz
2019-Dec-03 16:36 UTC
Re: [libvirt-users] What's the best way to make use of VLAN interfaces with VMs?
Laine I made the change and I can now ping across both bridges: br1 (192.168.0.0/24) and br1600 (192.168.1.0/24): br1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.0.110 netmask 255.255.255.0 broadcast 192.168.0.255 inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid 0x20<link> ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) RX packets 21608 bytes 10289553 (9.8 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 1372 bytes 131012 (127.9 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 br1600: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.110 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid 0x20<link> ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) RX packets 3429 bytes 173404 (169.3 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 112 bytes 9490 (9.2 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 // ping to another host with the same bridge br1 defined on 192.168.0.120 [root@clusterdev01 ~]# ping 192.168.0.120 PING 192.168.0.120 (192.168.0.120) 56(84) bytes of data. 64 bytes from 192.168.0.120: icmp_seq=1 ttl=64 time=0.481 ms 64 bytes from 192.168.0.120: icmp_seq=2 ttl=64 time=0.244 ms 64 bytes from 192.168.0.120: icmp_seq=3 ttl=64 time=0.242 ms 64 bytes from 192.168.0.120: icmp_seq=4 ttl=64 time=0.244 ms 64 bytes from 192.168.0.120: icmp_seq=5 ttl=64 time=0.237 ms ^C // ping to another host with the same bridge br1600 defined on 192.168.1.120 [root@clusterdev01 ~]# ping 192.168.1.120 PING 192.168.1.120 (192.168.1.120) 56(84) bytes of data. 64 bytes from 192.168.1.120: icmp_seq=1 ttl=64 time=0.316 ms 64 bytes from 192.168.1.120: icmp_seq=2 ttl=64 time=0.245 ms 64 bytes from 192.168.1.120: icmp_seq=3 ttl=64 time=0.176 ms 64 bytes from 192.168.1.120: icmp_seq=4 ttl=64 time=0.213 ms ^C However, for some reason, multicast has stopped working across the bridge interface, when it was working in the previous configuration (with br1 and br1.600). I test multicast using a multicast test app, binding the receiver to br1 on one host (192.168.0.120) and then binding the sender on br1 on another host (192.168.0.110). I also start an instance of tshark on each host to check which packets are being sent across. The multicast packets are seen by tshark to be crossing the bridge but for some reason the receiver app does not receive them. The bridges also have the multicast_querier and multicast_snooping flags enabled (e.g. for br1 on both hosts): [root@clusterdev01 ~]# cat /sys/class/net/br1/bridge/multicast_querier 1 [root@clusterdev01 ~]# cat /sys/class/net/br1/bridge/multicast_snooping 1 [root@clusterdev02 ~]# cat /sys/class/net/br1/bridge/multicast_querier 1 [root@clusterdev02 ~]# cat /sys/class/net/br1/bridge/multicast_snooping 1 // 1. start multicast test app sender and send packet across br1 (the multicast address of 239.11.12.13 is fixed for both apps, as well as multicast port 5555) [root@clusterdev01 bridge-multicast-test]# ./start-ipv4-mcast-sender.sh 192.168.0.110 Socket #1=0.0.0.0/0.0.0.0:5555, ttl=32, bind interface=/192.168.0.110 > 1234567890 > // 2. tshark on the sending host after sending packet [root@clusterdev01 ~]# tshark -i br1 -f "igmp or host 239.11.12.13" Running as user "root" and group "root". This could be dangerous. Capturing on 'br1' 1 0.000000000 192.168.0.110 → 239.11.12.13 UDP 52 5555 → 5555 Len=10 2 55.389831698 0.0.0.0 → 224.0.0.1 IGMPv2 60 Membership Query, general 3 60.194658894 192.168.0.115 → 224.0.0.251 IGMPv2 46 Membership Report group 224.0.0.251 // 3. tshark on the receiving host across bridge br1 [root@clusterdev02 ~]# tshark -i br1 -f "igmp or host 239.11.12.13" Running as user "root" and group "root". This could be dangerous. Capturing on 'br1' 1 0.000000000 192.168.0.120 → 224.0.0.22 IGMPv3 54 Membership Report / Join group 239.11.12.13 for any sources 2 0.902032534 192.168.0.120 → 224.0.0.22 IGMPv3 54 Membership Report / Join group 239.11.12.13 for any sources 3 41.448921858 192.168.0.110 → 239.11.12.13 UDP 60 5555 → 5555 Len=10 // 4. previously started multicast test app receiver and no packet received [root@clusterdev02 bridge-multicast-test]# ./start-ipv4-mcast-receiver.sh 192.168.0.120 Socket=0.0.0.0/0.0.0.0:5555, bind interface=/192.168.0.120 // NO PACKET APPEARS HERE :-( It's puzzling that the packet is seen to arrive on clusterdev02 but is not received by the test app. It's also odd to see IGMPv3 messages on the receiver and IGMPv2 messages on the sender. Investigating .... Richard On 11/29/19 12:15 PM, Richard Achmatowicz wrote:> Hi Laine > > What you have suggested sounds eminently reasonable. Thanks for your > advice. I'm going to give it a shot and report back. > > Richard > > On 11/27/19 1:38 PM, Laine Stump wrote: >> On 11/26/19 11:07 PM, Richard Achmatowicz wrote: >>> Hello >>> >>> I have a problem with attaching VMs to a VLAN interface. >>> >>> Here is my setup: I have several physical hosts connected by a >>> physical switch. Each host has two NICs leading to the switch, >>> which have been combined into a team, team0. Each host a has a >>> bridge br1, which has team0 as a slave. So communication between >>> hosts is based on the IP address of bridge br1 on each host. >>> >>> Up until recently, using libvirt and KVM, I was creating VMs which >>> had one interface attached the default virtual network and one >>> interface attached to the bridge: >>> >>> virt-install ... --network network=default --network bridge=br1 ... >>> >>> I would then statically assign an IP address to the bridge interface >>> on the guest when installing the OS. >>> >>> A few days ago, a VLAN was introduced to split up the network. I >>> created a new VLAN interface br1.600 on each of the hosts. My >>> initial attempt was to do try this: >>> >>> virt-install ... --network network=default --network bridge=br1.600 ... >>> >>> which did not work. It then dawned on me that a VLAN interface and a >>> bridge aren't treated the same. So I started to look for ways to >>> allow my VMs to bind to this new interface. >>> >>> This would seem to be a common situation. What is the best way to >>> work around this? >>> >>> Both the host bridge and the host VLAN interface already have their >>> assigned IP addresses and appear like this in libvirt: >>> >>> [root@clusterdev01 ]# ifconfig >>> br1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 >>> inet 192.168.0.110 netmask 255.255.255.0 broadcast >>> 192.168.0.255 >>> inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid >>> 0x20<link> >>> ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) >>> RX packets 833772 bytes 2976958254 (2.7 GiB) >>> RX errors 0 dropped 0 overruns 0 frame 0 >>> TX packets 331237 bytes 23335124 (22.2 MiB) >>> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 >>> >>> br1.600: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 >>> inet 192.168.1.110 netmask 255.255.255.0 broadcast >>> 192.168.1.255 >>> inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid >>> 0x20<link> >>> ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) >>> RX packets 189315 bytes 9465744 (9.0 MiB) >>> RX errors 0 dropped 0 overruns 0 frame 0 >>> TX packets 302 bytes 30522 (29.8 KiB) >>> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 >>> >>> [root@clusterdev01]# virsh iface-list --all >>> Name State MAC Address >>> --------------------------------------------------- >>> br1 active 1c:98:ec:1b:27:6d >>> br1.600 active 1c:98:ec:1b:27:6d >>> >>> [root@clusterdev01 sysadmin]# virsh iface-dumpxml br1.600 >>> <interface type='vlan' name='br1.600'> >>> <protocol family='ipv4'> >>> <ip address='192.168.1.110' prefix='24'/> >>> </protocol> >>> <protocol family='ipv6'> >>> <ip address='fe80::1e98:ecff:fe1b:276d' prefix='64'/> >>> </protocol> >>> <link state='up'/> >>> <vlan tag='600'> >>> <interface name='br1'/> >>> </vlan> >>> </interface> >>> >>> I tried following some suggestions which wrapped the vlan interface >>> in a bridge interface, but in ended up trashing the br1.600 >>> interface which was originally defined on the host. >>> >>> Is there a failsafe way to deal with such a situation? Am I doing >>> something completely wrong here? In would like br1.600 to behave >>> like br1 ..... >>> >>> Any suggestions or advice greatly appreciated. >> >> >> I guess what you need is for all the traffic from your guests to go >> out on the physical network tagged with vlan id 600, and you want >> that to be transparent to the guests, right? >> >> The simplest way to handle this is to create a vlan interface off of >> the ethernet that you have attached to br1 (not br1 itself), so it >> would be named something like "eth0.600", and then create a new >> bridge (call it, say "br600") and attach eth0.600 to br600. Then your >> guests would be created with "--network bridge=br600" >> >> (Note that Linux host bridges do now support vlan tagging (and maybe >> even trunking) at the port level, but libvirt hasn't added support >> for it. (in other words, "Patches Welcome!" :-)) >>
Richard Achmatowicz
2019-Dec-03 19:06 UTC
Re: [libvirt-users] What's the best way to make use of VLAN interfaces with VMs?
Even more puzzling, I reverted back to the old configuration to confirm what I had seen and found that it works in one direction but not the other: i.e. from 192.168.0.110 to 192.168.0.120, but not the other way around. Must be something with my configuration....which I can follow up on. So, thanks again for your help. Richard On 12/3/19 11:36 AM, Richard Achmatowicz wrote:> Laine > > I made the change and I can now ping across both bridges: br1 > (192.168.0.0/24) and br1600 (192.168.1.0/24): > > br1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 > inet 192.168.0.110 netmask 255.255.255.0 broadcast > 192.168.0.255 > inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid 0x20<link> > ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) > RX packets 21608 bytes 10289553 (9.8 MiB) > RX errors 0 dropped 0 overruns 0 frame 0 > TX packets 1372 bytes 131012 (127.9 KiB) > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 > > br1600: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 > inet 192.168.1.110 netmask 255.255.255.0 broadcast > 192.168.1.255 > inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid 0x20<link> > ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) > RX packets 3429 bytes 173404 (169.3 KiB) > RX errors 0 dropped 0 overruns 0 frame 0 > TX packets 112 bytes 9490 (9.2 KiB) > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 > > // ping to another host with the same bridge br1 defined on 192.168.0.120 > [root@clusterdev01 ~]# ping 192.168.0.120 > PING 192.168.0.120 (192.168.0.120) 56(84) bytes of data. > 64 bytes from 192.168.0.120: icmp_seq=1 ttl=64 time=0.481 ms > 64 bytes from 192.168.0.120: icmp_seq=2 ttl=64 time=0.244 ms > 64 bytes from 192.168.0.120: icmp_seq=3 ttl=64 time=0.242 ms > 64 bytes from 192.168.0.120: icmp_seq=4 ttl=64 time=0.244 ms > 64 bytes from 192.168.0.120: icmp_seq=5 ttl=64 time=0.237 ms > ^C > > // ping to another host with the same bridge br1600 defined on > 192.168.1.120 > [root@clusterdev01 ~]# ping 192.168.1.120 > PING 192.168.1.120 (192.168.1.120) 56(84) bytes of data. > 64 bytes from 192.168.1.120: icmp_seq=1 ttl=64 time=0.316 ms > 64 bytes from 192.168.1.120: icmp_seq=2 ttl=64 time=0.245 ms > 64 bytes from 192.168.1.120: icmp_seq=3 ttl=64 time=0.176 ms > 64 bytes from 192.168.1.120: icmp_seq=4 ttl=64 time=0.213 ms > ^C > > However, for some reason, multicast has stopped working across the > bridge interface, when it was working in the previous configuration > (with br1 and br1.600). > > I test multicast using a multicast test app, binding the receiver to > br1 on one host (192.168.0.120) and then binding the sender on br1 on > another host (192.168.0.110). I also start an instance of tshark on > each host to check which packets are being sent across. The multicast > packets are seen by tshark to be crossing the bridge but for some > reason the receiver app does not receive them. The bridges also have > the multicast_querier and multicast_snooping flags enabled (e.g. for > br1 on both hosts): > > [root@clusterdev01 ~]# cat /sys/class/net/br1/bridge/multicast_querier > 1 > [root@clusterdev01 ~]# cat /sys/class/net/br1/bridge/multicast_snooping > 1 > [root@clusterdev02 ~]# cat /sys/class/net/br1/bridge/multicast_querier > 1 > [root@clusterdev02 ~]# cat /sys/class/net/br1/bridge/multicast_snooping > 1 > > // 1. start multicast test app sender and send packet across br1 (the > multicast address of 239.11.12.13 is fixed for both apps, as well as > multicast port 5555) > > [root@clusterdev01 bridge-multicast-test]# > ./start-ipv4-mcast-sender.sh 192.168.0.110 > Socket #1=0.0.0.0/0.0.0.0:5555, ttl=32, bind interface=/192.168.0.110 > > 1234567890 > > > > // 2. tshark on the sending host after sending packet > > [root@clusterdev01 ~]# tshark -i br1 -f "igmp or host 239.11.12.13" > Running as user "root" and group "root". This could be dangerous. > Capturing on 'br1' > 1 0.000000000 192.168.0.110 → 239.11.12.13 UDP 52 5555 → 5555 Len=10 > 2 55.389831698 0.0.0.0 → 224.0.0.1 IGMPv2 60 Membership > Query, general > 3 60.194658894 192.168.0.115 → 224.0.0.251 IGMPv2 46 Membership > Report group 224.0.0.251 > > // 3. tshark on the receiving host across bridge br1 > > [root@clusterdev02 ~]# tshark -i br1 -f "igmp or host 239.11.12.13" > Running as user "root" and group "root". This could be dangerous. > Capturing on 'br1' > 1 0.000000000 192.168.0.120 → 224.0.0.22 IGMPv3 54 Membership > Report / Join group 239.11.12.13 for any sources > 2 0.902032534 192.168.0.120 → 224.0.0.22 IGMPv3 54 Membership > Report / Join group 239.11.12.13 for any sources > 3 41.448921858 192.168.0.110 → 239.11.12.13 UDP 60 5555 → 5555 Len=10 > > // 4. previously started multicast test app receiver and no packet > received > > [root@clusterdev02 bridge-multicast-test]# > ./start-ipv4-mcast-receiver.sh 192.168.0.120 > Socket=0.0.0.0/0.0.0.0:5555, bind interface=/192.168.0.120 > // NO PACKET APPEARS HERE :-( > > > It's puzzling that the packet is seen to arrive on clusterdev02 but is > not received by the test app. It's also odd to see IGMPv3 messages on > the receiver and IGMPv2 messages on the sender. > > Investigating .... > > Richard > > On 11/29/19 12:15 PM, Richard Achmatowicz wrote: >> Hi Laine >> >> What you have suggested sounds eminently reasonable. Thanks for your >> advice. I'm going to give it a shot and report back. >> >> Richard >> >> On 11/27/19 1:38 PM, Laine Stump wrote: >>> On 11/26/19 11:07 PM, Richard Achmatowicz wrote: >>>> Hello >>>> >>>> I have a problem with attaching VMs to a VLAN interface. >>>> >>>> Here is my setup: I have several physical hosts connected by a >>>> physical switch. Each host has two NICs leading to the switch, >>>> which have been combined into a team, team0. Each host a has a >>>> bridge br1, which has team0 as a slave. So communication between >>>> hosts is based on the IP address of bridge br1 on each host. >>>> >>>> Up until recently, using libvirt and KVM, I was creating VMs which >>>> had one interface attached the default virtual network and one >>>> interface attached to the bridge: >>>> >>>> virt-install ... --network network=default --network bridge=br1 ... >>>> >>>> I would then statically assign an IP address to the bridge >>>> interface on the guest when installing the OS. >>>> >>>> A few days ago, a VLAN was introduced to split up the network. I >>>> created a new VLAN interface br1.600 on each of the hosts. My >>>> initial attempt was to do try this: >>>> >>>> virt-install ... --network network=default --network bridge=br1.600 >>>> ... >>>> >>>> which did not work. It then dawned on me that a VLAN interface and >>>> a bridge aren't treated the same. So I started to look for ways to >>>> allow my VMs to bind to this new interface. >>>> >>>> This would seem to be a common situation. What is the best way to >>>> work around this? >>>> >>>> Both the host bridge and the host VLAN interface already have their >>>> assigned IP addresses and appear like this in libvirt: >>>> >>>> [root@clusterdev01 ]# ifconfig >>>> br1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 >>>> inet 192.168.0.110 netmask 255.255.255.0 broadcast >>>> 192.168.0.255 >>>> inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid >>>> 0x20<link> >>>> ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) >>>> RX packets 833772 bytes 2976958254 (2.7 GiB) >>>> RX errors 0 dropped 0 overruns 0 frame 0 >>>> TX packets 331237 bytes 23335124 (22.2 MiB) >>>> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 >>>> >>>> br1.600: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 >>>> inet 192.168.1.110 netmask 255.255.255.0 broadcast >>>> 192.168.1.255 >>>> inet6 fe80::1e98:ecff:fe1b:276d prefixlen 64 scopeid >>>> 0x20<link> >>>> ether 1c:98:ec:1b:27:6d txqueuelen 1000 (Ethernet) >>>> RX packets 189315 bytes 9465744 (9.0 MiB) >>>> RX errors 0 dropped 0 overruns 0 frame 0 >>>> TX packets 302 bytes 30522 (29.8 KiB) >>>> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 >>>> >>>> [root@clusterdev01]# virsh iface-list --all >>>> Name State MAC Address >>>> --------------------------------------------------- >>>> br1 active 1c:98:ec:1b:27:6d >>>> br1.600 active 1c:98:ec:1b:27:6d >>>> >>>> [root@clusterdev01 sysadmin]# virsh iface-dumpxml br1.600 >>>> <interface type='vlan' name='br1.600'> >>>> <protocol family='ipv4'> >>>> <ip address='192.168.1.110' prefix='24'/> >>>> </protocol> >>>> <protocol family='ipv6'> >>>> <ip address='fe80::1e98:ecff:fe1b:276d' prefix='64'/> >>>> </protocol> >>>> <link state='up'/> >>>> <vlan tag='600'> >>>> <interface name='br1'/> >>>> </vlan> >>>> </interface> >>>> >>>> I tried following some suggestions which wrapped the vlan interface >>>> in a bridge interface, but in ended up trashing the br1.600 >>>> interface which was originally defined on the host. >>>> >>>> Is there a failsafe way to deal with such a situation? Am I doing >>>> something completely wrong here? In would like br1.600 to behave >>>> like br1 ..... >>>> >>>> Any suggestions or advice greatly appreciated. >>> >>> >>> I guess what you need is for all the traffic from your guests to go >>> out on the physical network tagged with vlan id 600, and you want >>> that to be transparent to the guests, right? >>> >>> The simplest way to handle this is to create a vlan interface off of >>> the ethernet that you have attached to br1 (not br1 itself), so it >>> would be named something like "eth0.600", and then create a new >>> bridge (call it, say "br600") and attach eth0.600 to br600. Then >>> your guests would be created with "--network bridge=br600" >>> >>> (Note that Linux host bridges do now support vlan tagging (and maybe >>> even trunking) at the port level, but libvirt hasn't added support >>> for it. (in other words, "Patches Welcome!" :-)) >>>
Reasonably Related Threads
- Re: What's the best way to make use of VLAN interfaces with VMs?
- Re: What's the best way to make use of VLAN interfaces with VMs?
- Re: What's the best way to make use of VLAN interfaces with VMs?
- What's the best way to make use of VLAN interfaces with VMs?
- changue bridge name, libvirt refuses to take new name