CentOS - Mar 2017 - Mixed bonding and vlan on plain adapter possible?

Hello,
I have a CentOS 7.3 + updates server where my configuration arises from the
need to connect via iSCSI to a Dell PS Series storage array and Dell not
supporting bonding.
So that I need to use 2 nics on the same vlan to connect to iSCSI portal IP
and then use multipath.
Also, the iSCSI lan is on a dedicated vlan
I have only these 2 x 10Gbit adapters and I also need to put other vlans on
them through bonding. I plan to use active-backup as bonding mode.

My first tests were only with iSCSI in place to verify connection is ok
I followed these Dell guidelines, for both multipath and sysctl configs for
network adapters:
http://en.community.dell.com/techcenter/extras/m/white_papers/20442422
iSCSI vlan is 100 so that the configured devices are p1p1.100 and p1p2.100
and my sysctl config is:

net.ipv4.conf.p1p1/100.arp_announce=2
net.ipv4.conf.p1p2/100.arp_announce=2
net.ipv4.conf.p1p1/100.arp_ignore=1
net.ipv4.conf.p1p2/100.arp_ignore=1
#
net.ipv4.conf.p1p1/100.rp_filter=2
net.ipv4.conf.p1p2/100.rp_filter=2

So far so good and my lun is viewed this way through multipath
[root at ov300 etc]# multipath -l
364817197b5dfd0e5538d959702249b1c dm-3 EQLOGIC ,100E-00
size=1.0T features='0' hwhandler='0' wp=rw
`-+- policy='round-robin 0' prio=0 status=active
  |- 7:0:0:0 sde 8:64 active undef  running
  `- 8:0:0:0 sdf 8:80 active undef  running

I tried a test workload and both paths are used in a balanced way.

Now I temporarily stop the iSCSI layer and ifdown the p1p1.100 and p1p2.100
devices and put in place bonding on plain p1p1 and p1p2 interfaces and then
vlans over it and bridges (they are for VMs)

[root at ov300 ~]# cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: p1p1
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: p1p1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: a0:36:9f:2e:4d:80
Slave queue ID: 0

Slave Interface: p1p2
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 1
Permanent HW addr: a0:36:9f:2e:4d:82
Slave queue ID: 0
[root at ov300 ~]#

- ifcfg-bond1.65

DEVICE=bond1.65
VLAN=yes
BRIDGE=vlan65
ONBOOT=yes
MTU=1500
DEFROUTE=no
NM_CONTROLLED=no
IPV6INIT=no

- ifcfg-vlan65

DEVICE=vlan65
TYPE=Bridge
DELAY=0
STP=off
ONBOOT=yes
MTU=1500
DEFROUTE=no
NM_CONTROLLED=no
IPV6INIT=no

[root at ov300 network-scripts]# brctl show vlan65
bridge name bridge id STP enabled interfaces
vlan65 8000.a0369f2e4d80 no bond1.65
[root at ov300 network-scripts]#

The same for vlans 162, while for vlan 187 I only have the bond1.187
without a bridge on top of it

At the end I try to re-start the iSCSI components, but it seems now I have
iSCSI connection interrupted and not stable. During this phase the command

[root at ov300 network-scripts]# iscsiadm -m session -P1

has in its output for the 2 interfaces

Iface Netdev: p1p2.100
SID: 5
iSCSI Connection State: TRANSPORT WAIT
iSCSI Session State: FAILED
Internal iscsid Session State: REOPEN
...
SID: 6
iSCSI Connection State: TRANSPORT WAIT
iSCSI Session State: FREE
Internal iscsid Session State: REOPEN

and then

Iface Netdev: p1p2.100
SID: 5
iSCSI Connection State: TRANSPORT WAIT
iSCSI Session State: FREE
Internal iscsid Session State: REOPEN
...
Iface Netdev: p1p1.100
SID: 6
iSCSI Connection State: LOGGED IN
iSCSI Session State: LOGGED_IN
Internal iscsid Session State: NO CHANGE

and from multipath point of view a sequence of these:

[root at ov300 network-scripts]# multipath -l
364817197b5dfd0e5538d959702249b1c dm-2 EQLOGIC ,100E-00
size=1.0T features='0' hwhandler='0' wp=rw
`-+- policy='round-robin 0' prio=0 status=active
  |- 14:0:0:0 sde 8:64 active undef  running
  `- 13:0:0:0 sdf 8:80 failed faulty running

[root at ov300 network-scripts]# multipath -l
364817197b5dfd0e5538d959702249b1c dm-2 EQLOGIC ,100E-00
size=1.0T features='0' hwhandler='0' wp=rw
`-+- policy='round-robin 0' prio=0 status=active
  |- 14:0:0:0 sde 8:64 active undef  running
  `- 13:0:0:0 sdf 8:80 failed faulty running

[root at ov300 network-scripts]# multipath -l
364817197b5dfd0e5538d959702249b1c dm-2 EQLOGIC ,100E-00
size=1.0T features='0' hwhandler='0' wp=rw
`-+- policy='round-robin 0' prio=0 status=active
  |- 14:0:0:0 sde 8:64 active undef  running
  `- 13:0:0:0 sdf 8:80 failed undef  running

Should my config work or do you see any physical/network intrinsic problems
in it?
>From first tests it seems the more problematic adapter in iSCSI connection
is the one that at the time was the active slave in the active-backup
bond..... but I only did preliminary tests

Tomorrow I'm going to run further tests and verify better and deeper, but
any comment/suggestion would be appreciated in advance.

Thanks
Gianluca