similar to: Mixed bonding and vlan on plain adapter possible?

Hi all, Someone played with kickstart bonding with centos 6.4 ? CentOS 6.4, as upstream now support ifcae bonding in kickstart network section. I've an issue with configuring a second bonding iface in kicstart on CentOS 6.4. The first bonding (bond0) works as espected but the second is not configured during installation. I've a 6 nic server (two for "puclic" network, two for

Hello All, I have one CentOS 6 KVM virtualization server that I built around a year ago (best I can tell it was in October 2012) at which time I would have been installing 6.3 [0]. That particular install used the Consistent Network Device Naming [1] conventions (PCIe NICs are p1p1, p1p2). I started to build out a new KVM virt server (kickstarting a 6.4 install now as compared to 6.3 back then)

I'm setting up UEFI booting and got to the point of having the system talk to the dhcpd/tftpd server, grab the first image files (syslinux.efi) and then continuously request the secondary image file (ldlinux.e64). I'm wondering if I'm missing something or if someone can point me in the right direction of trouble shooting this. The tftp root has all the files to boot a BIOS type

Hi folks, I've got a Dell R320 running CentOS 7, and a 10G NIC. I'm running a DNS server on it, for testing. As part of my testing, I'm attempting to capture all the DNS queries arriving on the server, using tcpdump. However, tcpdump's performance is abysmal, and it loses lots of the packets. Here's the output when I stop the capture: # tcpdump -nn -i p1p1 -w

hi all We have a rh linux server connected to two HP SAN controllers, one an HSV200 (on the way out), the other an HSV400 (on the way in). (Via a Qlogic HBA). /etc/multipath.conf contains this : device { vendor "(COMPAQ|HP)" product "HSV1[01]1|HSV2[01]0|HSV300|HSV4[05]0" getuid_callout "/sbin/scsi_id -g -u -s /block/%n"

Hello, I have installed ocfs2 without problem and use it for a RAC10gR2. Only Clusterware files are ocfs2 type. multipath is also used. When I issue : mounted.ocfs2 -f I have a strange result: Device FS Nodes /dev/sda ocfs2 Unknown: Bad magic number in inode /dev/sda1 ocfs2 pocrhel2, pocrhel1 /dev/sdb ocfs2 Not mounted /dev/sdf

I am attempting to get multipath working with device-mapper (CentOS 4.2 and 4.3). It works on EVERY install of mine from RH (also v4.2, 4.3), but the same multipath.conf imported to all my installs of CentOS do not work. Note that I have tested a working 4.2 configuration file from RH on CentOS 4.2 and a working 4.3 configuration (it changed slightly) on CentOS 4.3. Neither worked. Our production

I have a dataset named DM with p1, p2, ...., p9 (9 columns, numerical values) I would like to calculate to multify each pair of columns (p1p2, p1p3,... p1p9, p2p3, p2p4.... p8p9) and assign them in p1p2, p1p3,... p1p9, p2p3, p2p4.... p8p9 In SAS, l=0; p_int_sum=0; do i=1 to 8; do j=(i+1) to 9; l=l+1; p{i}p{j}=p{i}*p{j}; end; end; I would like to know how to assign them in R I tried for

Currently, I have two networks configured via xml: virsh # net-dumpxml TestNetwork1 <network connections='2'> <name>TestNetwork1</name> <uuid>a76f665a-0196-4edb-81b4-340944a6869c</uuid> <forward dev='p1p1' mode='nat'> <nat> <port start='1024' end='65535'/> </nat> <interface

So I'm working with the iSCSI Initiator and an EqualLogic SAN. I'm not sure when this might have happened, but it appears that the /dev/sdc device is missing, yet the /dev/sdc1 partition exists AND is mountable. Is there a method to re-create the /dev/sdc device? I cannot dd or fdisk it, obviously, but I can mount the /dev/sdc1 partition and it works just fine. Not having the /dev/sdc

On 14/08/16 12:20, Anand Buddhdev wrote: Hi folks, I've discovered something. See below: > The packet rate is also not that high. From the sending side, this is > what I have: > > # tcpreplay -i qtx:p1p1 5min.pcap If I send packets without qtx, like this: tcpreplay -i p1p1 5min.pcap then tcpdump on the receiving box has no problem, and keeps up happily with the queries, and

On 11/21/2013 11:24 PM, Nehal J Wani wrote: > Currently, I have two networks configured via xml: > > virsh # net-dumpxml TestNetwork1 > <network connections='2'> > <name>TestNetwork1</name> > <uuid>a76f665a-0196-4edb-81b4-340944a6869c</uuid> > <forward dev='p1p1' mode='nat'> > <nat> >

Hi, i have a debian Etch x86_64 with a xen 3.1 on a kernel 2.6.18-xen. I have some DomU with Debian Etch. I installed open-iscsi, configure /etc/iscsi/iscsid.conf: --- node.active_cnx = 1 node.startup = automatic #node.session.auth.username = dima #node.session.auth.password = aloha node.session.timeo.replacement_timeout = 120 node.session.err_timeo.abort_timeout = 10

Hi all, I am trying to configure a failover multipath between 2 GNBD devices. I have a 4 nodes Redhat Cluster Suite (RCS) cluster. 3 of them are used for running services, 1 of them for central storage. In the future I am going to introduce another machine for central storage. The 2 storage machine are going to share/export the same disk. The idea is not to have a single point of failure

On Fri, Feb 14, 2020 at 8:05 PM Andre Goree <agoree@staff.atlantic.net> wrote: > I wanted to know if it's possible to use OVN networking and virtio > simultaneously in the same VM? Or am I wasting my time trying to get it to > work? > > In oVirt 4.x I was able to do it and also to intermix normal vnic and OVN based vnic. I needed to reproduced a problem I had in a

The reason for the behaviour observed below turned out to be that the device entry in /etc/multipath.conf was inadvertently appended *after* the devices section , rather than inside it - so that we had #devices { # device { # blah blah # } (file has a bunch of defaults commented out) # etc #} # # device { our settings } *rather than*

Dear all, After some trouble finding the right multipath.conf, I'm running Centos 5.5 against the SUN 7310 more or less successfully now. Unfortunately one issue remains: the SUN 7310 has two storage heads, H1 and H2, which are in a active/passive configuration. If I define a LUN on H1, everything works great. I edit multipath.conf, re-create the initrd and I find 8 paths with

All: ~> uname -srvmpio Linux 2.6.32-358.18.1.el6.x86_64 #1 SMP Wed Aug 28 17:19:38 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux ~> rpm -qa kernel\* | sort kernel-2.6.32-358.18.1.el6.x86_64 kernel-2.6.32-358.el6.x86_64 kernel-devel-2.6.32-358.18.1.el6.x86_64 kernel-devel-2.6.32-358.el6.x86_64 kernel-firmware-2.6.32-358.18.1.el6.noarch kernel-headers-2.6.32-358.18.1.el6.x86_64 My department has

Dear list, we have a relatively new Sun Storage 7310, where we connect CentOS 5.5 Servers (IBM LS21/LS41 Blades) via Brocade Switches, 4GBit FC. The Blades boot from SAN via qla2xxx, and have no harddisks at all. We want them to use multipathing from the very beginning, so /boot and / are already seen by multipathd. Problem is, that the Sun 7310 has two storage heads which run in

On Fri, 2016-03-18 at 13:02 -0400, Mike - st257 wrote: > Paul, > > > On Thu, Mar 17, 2016 at 5:47 PM, Digimer <lists at alteeve.ca> wrote: > On 17/03/16 04:47 PM, paul.greene.va at verizon.net wrote: > > Thanks, I followed the 2nd article, and it got the existing > virtual > > machines communicating with each other. > >