similar to: PBAX-Group with QuadBRI card, outgoing call problem

Hi all, I have a problem to park the call with #700 when the SIP phone and the asterisk PBAX run on the same machine. Call parking works well if the SIP phone that I use is on a remote pc in comparison with the asterisk on the which it is registered. If the sipphone is in the same pc where asterisk is installed the command #700 doesn't work, and in the asterisk's CLI I can see no

Good afternoon, I have to develop an Asterisk system in Spain that can support up to 8 simultaneos ISDN calls (4 BRI), initially only 6 simultaneos calls. I have been looking into VOIP-INFO and I found that the Junghanns card QuadBRI is a very good option. But when I look for a server to develop the system, the information is a bit more confuse. Any one have experience with this card? Which

Hello, We have a quadBRI in NT mode with bri_cpe_ptmp signalling and when connect a ISDN telephone to this nothings happen. What can I do? My config files are this: Zaptel.conf: loadzone=es defaultzone=es # qozap span definitions # most of the values should be bogus because we are not really zaptel span=1,1,3,ccs,ami span=2,1,3,ccs,ami span=3,1,3,ccs,ami span=4,1,3,ccs,ami bchan=1,2 dchan=3

Hello, We have been running a system based around the quadbri card from www.junghanns.net for around 3 weeks now. For the first two weeks everything was stable and ran well. In the last week a issue has appeared, described below: Someone attempts to call us, * sees an incoming call (it is anounced on the console e.g. "Accepting call from '' to '781950' on channel 2, span

Who is selling the quadBRI cards, which is everybody talking about? And how much does is costs? I'm looked on the site of junghanns.net, but there is no selling information. A seller in germany is favored.

Hello, I cannot make any call with my new quadBRI card from Junghanns.net in my asterisk box. My asterisk box is built on Fedora Core 3 linux system. After compiling drivers from junghanns.net the card driver was loaded correctly with - modprobe zaptel - insmod qozap.ko ( as FC3 is running a 2.6 linux kernel) - ztcfg -vvv ( shows 12 channels correctly configured and the 4 leds on the card were

Hi, I mistakenly posted this to Dev list.... I wonder if I use quadbri or octobri cards to insert Asterisk between ISDN PBX and ISDN line - if power of Asterisks fails - will those card connect PBX directly to ISDN line ? If not are there any other simple switching devices, that would do this (in power fail it will connect ISDN PBX to ISDN lines directly) ? Thanks in advance, regards, Rob.

Hi, I'm getting unreliable dtmf recognition (it works fine for 4-5 digits, errors (duplicates) on more), when transferred inband from gsm gateway to NT port of quadbri under bristuffed Asterisk..... Since Asterisk is claimed to have good dtmf recognizer, I suspect there are some settings to workarouned... I've tried dtmf relax, but didn't help, so I suspect gain settings.... Is

I got the same problem, and what i change it was point-to-point to point-to-multi-point, and I used normal patch cable to connect the ISDN card to ISDN connector, and I used TE mode. In italy work like that I hope that will help you, I used also bristuff. Good luck ________________________________ Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]

Hey, If anyone supplies or knows where I can get either an Eicon Diva V-4BRI or a Junghanns QuadBRI card in Australia, please could you contact me offlist? Also, if anyone has any second-hand ones they need to get rid of, I'd be interested in making an offer! I've been checking eBay, but there don't seem to be any of these available at the moment. Thanks, Avi -- National Manager -

Hello, I have an Asterisk system with kernel 2.6.18.1 and one quadbri. I have installed the latest bristuff patches (0.3.0-PRE-1s). The system works fine, but when I do a "reboot", the system hangs unloading module "qozap". Is there any known problem with latest 2.6 kernels and qozap module? Thanks. -- Paco Brufal <pbrufal@servitux.es> ServiTux Servicios

Hi, I'm using a revision 6822-enabled Dahdi-Tools (see https://issues.asterisk.org/view.php?id=13897) with a Junghanns QuadBRI. 1. Do I still need qozap driver ? If positive, how is it recommended to get it ? 2. Which line should be included in /etc/dahdi/modules to have the appropriate driver loaded ? 3. The process I'm planning to use is : A- Hand edit /etc/dadhi/modules,

Hi, I'll soon replace a Junghanns OctoBRI with a Junghanns QuadBRI. As both use wcb4xxp driver (dahdi 2.3.0, libpri 1.4.10.2 and asterisk 1.6.1), I'm planning to proceed this way : 1. Edit 2 versions of files /etc/dahdi/system.conf and /etc/asterisk/dahdi-channels.conf (one for each card). 2. Link current system.conf and dahdi-channels.conf to QuadBRI files. 3. Power PC off 4. Swap cards

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hi, I'm using Asterisk 1.6.1.18 with latest Dahdi Linux and Tools (rev 8854) and libpri 1.4.10.2. During installation, I'm facing this : # dahdi_genconf -v system Default parameters from /etc/dahdi/genconf_parameters Empty configuration -- no spans Of course, I've got span descriptions in /etc/dahdi/genconf_parameters : .... pri_termtype SPAN/1 TE SPAN/2

Hello, Is anybody there using quadBRI form Junghanns.net with Asterisk ? I would like to order that card but first would like to hear some opinions. Thank you in advance Bartosz

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

Hello, I have bought a targeta quadbri. I want to realize a PBX server to send and to receive fax on lines BRI. I have installed asterisk and the drivers of quadbri (bristuff_0.2.0-RC7b). I downloaded and installed the module spandsp-0.0.2pre10 When i send a fax from the fax machine to asterisk, the application rx_fax saves the fax in a file on the hard disk. The problem comes when I try to send a

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out:

Hello Asterisk users. We have a quadBRI card installed and have the following problem. When starting Asterisk, the card is up and works perfect. But if no one uses it for 2-3 hours, the card seems to change status. If I try making a call from my sip phone to an extarnal telephone then asterisk registers that I'm trying to call, i.e. it's not a bridged but a show channels gives this