Francesco Peeters (Asterisk)
2005-Dec-18 12:05 UTC
[Asterisk-Users] Is it me, or is 1.2.1 slower than 1.0.9?
Hi all, I just wiped my system and did a clean Asterisk 1.2.0 install with Bristuff 0.3 Pre 1c. (It doesn't work with 1.2.1 yet!) :-( Is it my server or is 1.2.0 considerably slower than 1.0.9 was? It seems to me that all actions take noticably longer than before! Also, despite setting DYNAMIC_FEATURES=>automon in the extensions.conf globals section and uncommenting automon=>*1 in features.conf, nothing happens when pressing *1 When I change blinsxfer in features.conf to anything different than #, it no longer works. It only works with my softphones anyway, as my ZAP connected ISDN phone never transfers to begin with! I'm getting depressed, because I know all these nice features are there, and I cannot get any of them working! (Once it works, I can deploy it at 2 other locations and really start saving money...) Any suggestions? TIA! -- F Peeters PIII 450 - 1 GB - * 1.2 - BRIstuff 0.3.0 Pre 1c - Florz patch 2 Sweex HFC-PCI modes=2 sync_slave=2 timer_card=0 Cologne HFC-S pins #52, #54, #55 connected in parallel for synching.
Francesco Peeters (Asterisk)
2005-Dec-18 15:14 UTC
[Asterisk-Users] Is it me, or is 1.2.1 slower than 1.0.9?
On Sun, December 18, 2005 20:05, Francesco Peeters (Asterisk) said:> Hi all, > > I just wiped my system and did a clean Asterisk 1.2.0 install with > Bristuff 0.3 Pre 1c. (It doesn't work with 1.2.1 yet!) :-( > > Is it my server or is 1.2.0 considerably slower than 1.0.9 was? > > It seems to me that all actions take noticably longer than before! > > Also, despite setting DYNAMIC_FEATURES=>automon in the extensions.conf > globals section and uncommenting automon=>*1 in features.conf, nothing > happens when pressing *1 >Solved that...> When I change blinsxfer in features.conf to anything different than #, it > no longer works. >That too...> It only works with my softphones anyway, as my ZAP connected ISDN phone > never transfers to begin with! >And here we come to the root cause: The Siemens ISDN DECT station stubbornly refuses to do DTMF unless I manually go in to a menu 2 levels deep to temporarily turn it on... No preference setting, etc. It even gets worse with non Siemens DECT handsets (using the GAP protocol), as these do not even support the keypad switching, which means I first have to do a DECT transfer to a Siemens handset or the base, before I can xfer to a non-DECT extension or external peer...> I'm getting depressed, because I know all these nice features are there, > and I cannot get any of them working! (Once it works, I can deploy it at 2 > other locations and really start saving money...)So my depression is somewhat lifted, as I will be proceeding with the other 2 locations, as I now have all features working, however I need to figure out how to properly work around the Siemens issue, as the other sites too use Siemens ISDN hardware! :rolls eyes: Time to bring out the AMD 1000 box and start prepping that one! -- F Peeters PIII 450 - 1 GB - * 1.2 - BRIstuff 0.3.0 Pre 1 - Florz patch 2 Sweex HFC-PCI modes=2 sync_slave=2 timer_card=0 Cologne HFC-S pins #52, #54, #55 connected in parallel for synching.
Tomislav Parcina
2005-Dec-20 01:13 UTC
[Asterisk-Users] Re: Is it me, or is 1.2.1 slower than 1.0.9?
In article <1610.10.50.164.11.1134944046.squirrel@www.fampeeters.com>, francesco@fampeeters.com says...> > Also, despite setting DYNAMIC_FEATURES=>automon in the extensions.conf > > globals section and uncommenting automon=>*1 in features.conf, nothing > > happens when pressing *1 > > > > Solved that... > > > When I change blinsxfer in features.conf to anything different than #, it > > no longer works. > > > That too...You can say what was the problem. -- Tomislav Parcina ime.prezime@email.t-com.hr
Francesco Peeters (Asterisk)
2005-Dec-20 07:05 UTC
[Asterisk-Users] Re: Is it me, or is 1.2.1 slower than 1.0.9?
On Tue, December 20, 2005 9:13, Tomislav Parcina said:> In article <1610.10.50.164.11.1134944046.squirrel@www.fampeeters.com>, > francesco@fampeeters.com says... >> > Also, despite setting DYNAMIC_FEATURES=>automon in the extensions.conf >> > globals section and uncommenting automon=>*1 in features.conf, nothing >> > happens when pressing *1 >> > >> >> Solved that... >> >> > When I change blinsxfer in features.conf to anything different than #, >> it >> > no longer works. >> > >> That too... > > You can say what was the problem. > >I did: The Siemens ISDN Base was... -- F Peeters PIII 450 - 1 GB - * 1.2 - BRIstuff 0.3.0 Pre 1 - Florz patch 2 Sweex HFC-PCI modes=2 sync_slave=2 timer_card=0 Cologne HFC-S pins #52, #54, #55 connected in parallel for synching.