If you ring into * and leave voicemail It does not reset the line Any ideas would be appreciated Regards Mick
On Thu, 2003-11-06 at 16:40, mick@netexpress.com.au wrote:> If you ring into * and leave voicemail > > It does not reset the line > > Any ideas would be appreciatedMick, You need to learn how to ask questions in a technical forum. You have left so many pieces of information out that we could spend a week asking you questions. You need to be upfront about hardware, software version, and occasionally phase of the moon during attempt to give us the proper information to help you. But as I think I have a working swamy hat here I'll try and answer your question. If I miss any points, you will then have been pre-warned to supply more information when asking questions. I am betting you have a X100P card. I'm betting you have not enabled progress detection. I'm betting you do not have disconnect supervision. All this combines to give you a simple problem that asterisk doesn't know when the line was hungup and continues to try and service it. You can fix the problem by either getting the correct service, configuring your system to fake disconnect functions, or set a timeout on the call as you enter the section that leaves voicemail so the time allowed in this section is appropriately short and asterisk will hang up afterwords. -- Steven Critchfield <critch@basesys.com>
---- Original Message ----- From: <mick@netexpress.com.au> To: <asterisk-users@lists.digium.com> Sent: Thursday, November 06, 2003 5:40 PM Subject: [Asterisk-Users] voicemail> If you ring into * and leave voicemail > > It does not reset the line > > Any ideas would be appreciated >What is the source of the call? Is it coming from a SIP Phone, an FXS card, a telephone line via an FXO card, or something else? Sean
Sean Thanks for the response The call was external over PSTN All I did was enable max time for voicemail. Regards Mick -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Sean P. Robertson Sent: Friday, 7 November 2003 10:19 AM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] voicemail ---- Original Message ----- From: <mick@netexpress.com.au> To: <asterisk-users@lists.digium.com> Sent: Thursday, November 06, 2003 5:40 PM Subject: [Asterisk-Users] voicemail> If you ring into * and leave voicemail > > It does not reset the line > > Any ideas would be appreciated >What is the source of the call? Is it coming from a SIP Phone, an FXS card, a telephone line via an FXO card, or something else? Sean _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users
Hello Has anyone implemented a voicemail system for an existing cisco call manager express VOIP setup. I am looking for a open source based software which can integrate with my existing Cisco call manager express VOIP (based on 3640 router) with individual users having their own voicemail box. Thanks, Deepak -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031216/f40d2e72/attachment.htm
Is something different about the latest implementation of voicemail in asterisk? I have been away from asterisk for about 6 months and finally have a chance to take a second look at it. From what I remember all you needed to do to setup voicemail was to perform som basic modifications to the voicemail.conf and extensions.conf files. I am having two problems: 1. I can leave but cannot retrieve my voicemails. I call my extension number but cant find a combination that allows me to break into an admin menu for retrieval. 2. I could be dreaming but I thought I remember more advanced features available after leaving a VM. (Review, delete, etc.) I could be remembering incorrectly as well. Can anyone refresh my memory. (BTW - I'm using the latest stable build from today) Thanks, Chad
To add to the comments... You can apply the following patch for advanced features that you are looking for.... http://bugs.digium.com/bug_view_page.php?bug_id=0000156 -gcc -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Tilghman Lesher Posted At: Saturday, February 21, 2004 4:34 PM Posted To: Asterisk User Group Conversation: [Asterisk-Users] VoiceMail Subject: Re: [Asterisk-Users] VoiceMail On Saturday 21 February 2004 04:24, Chad Brown wrote:> Is something different about the latest implementation of voicemail in> asterisk?Yes, it's been rewritten to allow multiple organizations within the same Asterisk system. There are also multiple other features that you can check out by looking at the ChangeLog.> 1. I can leave but cannot retrieve my voicemails. I call my extension > number but cant find a combination that allows me to break into an > admin menu for retrieval.Are you dialling an extension which calls VoiceMailMain() ?> 2. I could be dreaming but I thought I remember more advanced features> available after leaving a VM. (Review, delete, etc.) I could be > remembering incorrectly as well.Nope. You're welcome to write and contribute that addition, though. -Tilghman _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
For some reason voicemails are not being played back. I can log into the voicemail system and i get the menu. its all fine till the point asterisk is announcing info abt the mail but when it comes to playing the mail i hear nothing then it quickly gones on to the next mail. If anyone has encountred such a problem. any pointers will be helpful. -- regards Vikram (http://www.vicramresearch.com)
Hi I have an asterisk voicemail system connected directly to a pri, there are no extensions connected to the asterisk box, anyway my questions is, can I get asterisk to call an associated phone number when a voicemail box has a message? Thanks in advance for your help Robb
How would one hack the voicemail app to play saved vm messages back in a 'most recent first' fashion ? What source file is this defined in ? Thanks, Chris Clifton
Voicemail,from wiki pages: Returns -1 on error or mailbox not found, or if the user hangs up. Otherwise, it returns 0. Question is ... how can I trap the error code to divert to a message like "This user is offline and has no mailbox, goodbye!". Tnx ! -- Best regards, Alessio mailto:afoc@interconnessioni.it
HI ALL; Is asterisk voicemail service can be run under H323 or it just run under SIP. mohammad -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040617/0f9d85be/attachment.htm
Which voicemail is current and latest?
Voicemail
or
Voicemail2
I thot it was voicemail2 but this link sort of indicates otherwise...at
the bottome of the page it says:
Old version:
. Asterisk cmd VoiceMail2
http://www.voip-info.org/wiki-Asterisk+cmd+VoiceMail2#comments
--
respectfully, Joseph - (606) 477-2355 x140
------=============
J> Which voicemail is current and latest? J> Voicemail J> or J> Voicemail2 I think Voicemail ist the latest. Greetings Gunnar
For some reason, voicemail doesn't seem to be firing. is there something
that anyone can see wrong with my extensions.conf ?
exten => 4001,1,SetCalledParty("Justin" <4001>)
exten => 4001,2,Dial(SCCP/justin)|5
exten => 4001,3,Voicemail,u4001
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20040915/328940d6/attachment.htm
Here's a newbie question for you. The features list of Asterisk shows that you can check you email via web based browser, How do I set that up? Is there a wiki for that? I must just be overlooking it. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040929/3a909406/attachment.htm
hello to all: to help they can to me with this, which desire to do is that the voicemail warns to me with a call extesion that corresponds whenever nuevo.he has a message reviewed the Web but nonencounter like doing it. Thanks Rodrigo
You need to do a better job translating this to english, it is not possible to understand your question the way it is worded. If you are asking for outcall notification of voicemail messages have a look here; http://www.voip-info.org/tiki-index.php?page=Asterisk%20bounty%20outcall %20notification%20application And here; http://bugs.digium.com/bug_view_page.php?bug_id=0002824> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of > Rodrigo Benavides > Sent: Tuesday, November 23, 2004 8:32 AM > To: asterisk-users@lists.digium.com > Subject: [Asterisk-Users] Voicemail > > hello to all: > > to help they can to me with this, which desire to do is that > the voicemail warns to me with a call extesion that > corresponds whenever nuevo.he has a message reviewed the Web > but nonencounter like doing it. > > Thanks > > Rodrigo > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
Hello All,
We have VOIP running on Asterisk.
We are having problems with voicemail. As in when a customer is
having more than 1 phone numbers and he wants to check his mailbox
when he dials in to check his voicemail it should pick the primary
mailbox but it is picking up the wrong phone extension and verifying
the primary mailbox password with that extension which gives an error
password not verified.
Help Appreciated
Thank you,
Sharon wrote:> Hello All, > We have VOIP running on Asterisk. > We are having problems with voicemail. As in when a customer is > having more than 1 phone numbers and he wants to check his mailbox > when he dials in to check his voicemail it should pick the primary > mailbox but it is picking up the wrong phone extension and verifying > the primary mailbox password with that extension which gives an error > password not verified. > Help Appreciatedperhaps you could post the relevant configuration files, which would be quite useful for the people here to help you. flynn
> when a customer is > having more than 1 phone numbers and he wants to check his mailbox > when he dials in to check his voicemail it should pick the primary > mailbox but it is picking up the wrong phone extension and verifyingSounds like it uses the callerid extension as the mailbox. What you want for a global mailbox is to supply it in the Voicemail command as in u2000 or b2000 or s2000.
Around 10000 customers. On Fri, 10 Dec 2004 17:24:56 +0100, Wilson Pickett <wilson.pickett@gmail.com> wrote:> How many customers, Sharon? >
Hello: I'd like to expire the password for a voicemailbox the first time a user logs into their mailbox. I am using Asterisk 1.0.2. Is this possible? If so can someone share their thoughts? Thanks,Steve
I installed Asterisk Voicemail in an office and now most of the employees are complaining that when they're listening to the messages, it takes "forever" to listen to their messages. The reason being is that before the message is played, the voicemail says the full date and time when the message arrived and that takes a long time. It's like: Friday ......... June........20th......... 2000.......and.......5....... etc (you get the idea). Is there anyway to shorten that or even give users the option to not play that? Thanks, Waldo
On 6/20/05, Waldo Rubinstein <waldo@trianet.net> wrote: <snip>> Is there anyway to shorten that or even give users the option to not play that?Voicemail as some options that can help you with that. See http://www.voip-info.org/tiki-index.php?page=Asterisk+config+voicemail.conf It can be configured per user hth
Hi, if only you see the page of the Apache put the following thing http://(The asterisk ip)/cgi-bin/vmail.cgi On 6/20/05, Time Bandit <timebandit001@gmail.com> wrote:> On 6/20/05, Waldo Rubinstein <waldo@trianet.net> wrote: > <snip> > > Is there anyway to shorten that or even give users the option to not play that? > > Voicemail as some options that can help you with that. > > See http://www.voip-info.org/tiki-index.php?page=Asterisk+config+voicemail.conf > > It can be configured per user > > hth > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
I am trying to setup voicemail for my iaxy device, however, i cannot get it to work voicemail never picks up. Below is my config. Am i doing anything wrong here>From my Extensions.conf fileexten => 7403,1,Dial(IAX2/7403/10) exten => 7403,2,Voicemail(u7403) exten => 7403,102,Voicemail(b7403) exten => 7403,103,Hangup>From my voicemail.conf[telx.com] 7403 => 7403 Thanks Mike -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050623/2e9a3e01/attachment.htm
On Thu, 2005-06-23 at 23:19 -0400, Michael Di Martino wrote:> I am trying to setup voicemail for my iaxy device, however, > i cannot get it to work voicemail never picks up. Below is my config. > Am i doing anything wrong here > > >From my Extensions.conf file > exten => 7403,1,Dial(IAX2/7403/10)You did not specify a timeout in the dial command. Change it to: exten => 7403,1,Dial(IAX2/7403/10,xx) <--- where xx is the number of seconds you want the Dial command to attempt to connect the call before it returns and proceeds to the next priority (i.e. voicemail).> exten => 7403,2,Voicemail(u7403) > exten => 7403,102,Voicemail(b7403) > exten => 7403,103,Hangup > > >From my voicemail.conf > [telx.com] > 7403 => 7403 > > > Thanks > MikeHope that helps. -Seth
Ok I have added the timeout value but it still does not pick. However jus to test voicemail function I comment out the first line and voice does pick up. What could be wrong. exten => 7403,1,Dial(IAX2/u7403/1/5) exten => 7403,2,Voicemail(u7403) exten => 7403,102,Voicemail(b7403) exten => 7403,103,Hangup -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Seth Remington Sent: Friday, June 24, 2005 12:03 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] voicemail On Thu, 2005-06-23 at 23:19 -0400, Michael Di Martino wrote:> I am trying to setup voicemail for my iaxy device, however, i cannot > get it to work voicemail never picks up. Below is my config. > Am i doing anything wrong here > > >From my Extensions.conf file > exten => 7403,1,Dial(IAX2/7403/10)You did not specify a timeout in the dial command. Change it to: exten => 7403,1,Dial(IAX2/7403/10,xx) <--- where xx is the number of seconds you want the Dial command to attempt to connect the call before it returns and proceeds to the next priority (i.e. voicemail).> exten => 7403,2,Voicemail(u7403) > exten => 7403,102,Voicemail(b7403) > exten => 7403,103,Hangup > > >From my voicemail.conf > [telx.com] > 7403 => 7403 > > > Thanks > MikeHope that helps. -Seth _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
I need to see if we can make the voicemail do the following: After they reach the voicemail, and left a message or not, they should be able to dial 0 to reach back the main menu or and operator. Any ideas? Thanks, Carlos Alperin -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050708/26da0b7d/attachment.htm
> I need to see if we can make the voicemail do the following: > > After they reach the voicemail, and left a message or not, they should be able to dial 0 toreach back the main menu or and operator.> > Any ideas?As ususal, first look in /usr/src/asterisk/configs. If you dig through the voicemail.conf.sample, you should find something like: operator=yes
When I receive a voicemail notify via e-mail I would like receive not the sender phone-number, but the sender name. Where can I configure this and how? Is it possible to have some example? Thank Luca
-----Original Message-----
From: asterisk-users-bounces@lists.digium.com
[mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of
lucabencini@tin.it
Sent: Sunday, September 18, 2005 8:32 AM
To: asterisk-users@lists.digium.com
Subject: [Asterisk-Users] Voicemail
When I receive a voicemail notify via e-mail I would like receive not
the sender phone-number, but the sender name. Where can I configure
this and how? Is it possible to have some example?
Thank
Luca
This will do it (in voicemail.conf) but I think the default does as
well. Are you actually getting caller ID name delivered when a call
comes it?
emailbody=${VM_NAME} <${VM_MAILBOX}>\n\nYou have a new voicemail message
from ${VM_CALLERID}. The message is ${VM_DUR} long and was left on
${VM_DATE}.
Download cvs head and look at /usr/src/asterisk/configs/voicemail.conf.sample All of the variables for email, page, etc are listed in the sample files, it is more comprehensive than many of the other samples.> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Matt > Sent: Sunday, September 18, 2005 6:53 PM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: [Asterisk-Users] Voicemail > > While we are on the subject.. how do you modify the TXT message that > gets send to the 'pager'... Is that hard coded.. or can that be > changed? No variables I change in voicemail.conf seem to change the > from address, etc. > > On 9/18/05, Damon Estep <damon@suburbanbroadband.net> wrote: > > > > > > -----Original Message----- > > From: asterisk-users-bounces@lists.digium.com > > [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of > > lucabencini@tin.it > > Sent: Sunday, September 18, 2005 8:32 AM > > To: asterisk-users@lists.digium.com > > Subject: [Asterisk-Users] Voicemail > > > > When I receive a voicemail notify via e-mail I would like receivenot> > the sender phone-number, but the sender name. Where can I configure > > this and how? Is it possible to have some example? > > Thank > > Luca > > > > This will do it (in voicemail.conf) but I think the default does as > > well. Are you actually getting caller ID name delivered when a call > > comes it? > > > > emailbody=${VM_NAME} <${VM_MAILBOX}>\n\nYou have a new voicemailmessage> > from ${VM_CALLERID}. The message is ${VM_DUR} long and was left on > > ${VM_DATE}. > > _______________________________________________ > > --Bandwidth and Colocation sponsored by Easynews.com -- > > > > Asterisk-Users mailing list > > Asterisk-Users@lists.digium.com > > http://lists.digium.com/mailman/listinfo/asterisk-users > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ > --Bandwidth and Colocation sponsored by Easynews.com -- > > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users
Hi, I'm trying to translate the voicemail application to my local language. I want to translate the notification email which Asterisk send when you have new massages. Where I can find this file ?? Cheers to all Andrew
Hi, I have my voicemails accounts configured with delete=yes|attach=yes Today I had problems with my smtp server and messages were not sent to users, BUT were deleted from the server. Is there a way to delete voicemail msgs only if e-mail is sent successfully??? Thank you Dov -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060113/52244800/attachment.htm
Dear I am using trixbox,I want ot disable and enable voicemail from command line At asterisk@home v 2.8 I was using this command and was working successfully Database put AMPUSER/9990999 voicemail default And Database put AMPUSER.9990999 voicemail disables But at trixbox its not working Any ideas pleas Regards ********************************************* No employee or agent is authorized to conclude any binding agreement on behalf of Xplorium with another party by e-mail without express written confirmation by an officer of Xplorium. Any views expressed by an individual in this electronic message do not necessarily reflect views of Xplorium or its subsidiaries and associates. This electronic message and its attachments are solely addressed to the addressee(s), and contain confidential information protected from disclosure belonging to Xplorium. If you are not the intended addressee of this electronic message and its attachments, kindly delete it immediately from your system and notify the sender by electronic mail. You must not copy this message or attachment or disclose its content to any other person. Xplorium does not guarantee the integrity of this electronic message and any of its attachments, or that they are free from computer viruses or other defects. ********************************************* -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060630/70d12dd2/attachment.htm
Khaled Chehab wrote:> > I am using trixbox,I want ot disable and enable voicemail from command line > At asterisk@home v 2.8 I was using this command and was working successfully ><snip>> > But at trixbox its not working > Any ideas pleas >Did you try checking with the people who _wrote_ trixbox? Perhaps they have a forum or at least mailing list of some sort that could answer your question(s)? Flynn
Dear I am using trixbox,I want ot disable and enable voicemail from command line At asterisk@home v 2.8 I was using this command and was working successfully Database put AMPUSER/9990999 voicemail default And Database put AMPUSER.9990999 voicemail disables But at trixbox its not working Any ideas pleas Regards ********************************************* No employee or agent is authorized to conclude any binding agreement on behalf of Xplorium with another party by e-mail without express written confirmation by an officer of Xplorium. Any views expressed by an individual in this electronic message do not necessarily reflect views of Xplorium or its subsidiaries and associates. This electronic message and its attachments are solely addressed to the addressee(s), and contain confidential information protected from disclosure belonging to Xplorium. If you are not the intended addressee of this electronic message and its attachments, kindly delete it immediately from your system and notify the sender by electronic mail. You must not copy this message or attachment or disclose its content to any other person. Xplorium does not guarantee the integrity of this electronic message and any of its attachments, or that they are free from computer viruses or other defects. ********************************************* -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060703/fe97607f/attachment.htm
Dear I am using trixbox,I want ot disable and enable voicemail from command line At asterisk@home v 2.8 I was using this command and was working successfully Database put AMPUSER/9990999 voicemail default And Database put AMPUSER.9990999 voicemail disables But at trixbox its not working Any ideas pleas Regards ********************************************* No employee or agent is authorized to conclude any binding agreement on behalf of Xplorium with another party by e-mail without express written confirmation by an officer of Xplorium. Any views expressed by an individual in this electronic message do not necessarily reflect views of Xplorium or its subsidiaries and associates. This electronic message and its attachments are solely addressed to the addressee(s), and contain confidential information protected from disclosure belonging to Xplorium. If you are not the intended addressee of this electronic message and its attachments, kindly delete it immediately from your system and notify the sender by electronic mail. You must not copy this message or attachment or disclose its content to any other person. Xplorium does not guarantee the integrity of this electronic message and any of its attachments, or that they are free from computer viruses or other defects. ********************************************* -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060703/152b2bc0/attachment.htm
Dear I am using trixbox,I want ot disable and enable voicemail from command line At asterisk@home v 2.8 I was using this command and was working successfully Database put AMPUSER/9990999 voicemail default And Database put AMPUSER.9990999 voicemail disables But at trixbox its not working Any ideas pleas Regards ********************************************* No employee or agent is authorized to conclude any binding agreement on behalf of Xplorium with another party by e-mail without express written confirmation by an officer of Xplorium. Any views expressed by an individual in this electronic message do not necessarily reflect views of Xplorium or its subsidiaries and associates. This electronic message and its attachments are solely addressed to the addressee(s), and contain confidential information protected from disclosure belonging to Xplorium. If you are not the intended addressee of this electronic message and its attachments, kindly delete it immediately from your system and notify the sender by electronic mail. You must not copy this message or attachment or disclose its content to any other person. Xplorium does not guarantee the integrity of this electronic message and any of its attachments, or that they are free from computer viruses or other defects. ********************************************* -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060711/728cb896/attachment.htm