thr3ads.net - Xen devel - [Xen-devel] Xen 3.0 Xend loses network

If this information is useful, please help other people find it:
Share via:

Jurgen Stroo

2005-Jun-05 10:57 UTC

[Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Hi list.

I started with Xen yesterday, but I am facing a bit of a problem.
My system had always configure eth0 with 10.0.0.4/8

I am using Xen unstable source (on Debian sid)

Now I installed Xen, rebooted the machine, and first the usual network is
coming up and then the xend will be started.

I''ll end up with this, but I am wondering if this should be the way of
things to be configured:

megalosaurus:~# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:40:63:D7:A3:82
          inet addr:10.0.0.4  Bcast:10.255.255.255  Mask:255.0.0.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:807379 errors:0 dropped:0 overruns:0 frame:0
          TX packets:680984 errors:0 dropped:0 overruns:0 carrier:0
          collisions:174 txqueuelen:1000
          RX bytes:800654135 (763.5 MiB)  TX bytes:52893851 (50.4 MiB)
          Interrupt:11 Base address:0xec00

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:19 errors:0 dropped:0 overruns:0 frame:0
          TX packets:19 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:2004 (1.9 KiB)  TX bytes:2004 (1.9 KiB)

tap0      Link encap:Ethernet  HWaddr EE:F6:D7:D8:F4:F8
          inet addr:10.0.0.150  Bcast:10.255.255.255  Mask:255.0.0.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:21 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:500
          RX bytes:0 (0.0 b)  TX bytes:882 (882.0 b)

veth0     Link encap:Ethernet  HWaddr 00:40:63:D7:A3:82
          inet addr:10.0.0.4  Bcast:10.255.255.255  Mask:255.0.0.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:120 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:32280 (31.5 KiB)

vif0.0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:120 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:32280 (31.5 KiB)  TX bytes:0 (0.0 b)

xen-br0   Link encap:Ethernet  HWaddr 00:00:00:00:00:00
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

After the system boots and the network and xend is started, nothing works,
with this configuration.

Actually, it works now after restarting the network
(/etc/init.d/networking) and after restarting xend (sometimes a couple of
times though)

I can''t find anywhere in the docs if eth0 should be configured like
this.
Sometimes I am experiencing lots of lag, as if these IP''s are
conflicting with
each other.

The whole networking thing seems not to be configured right.

for completeness:

megalosaurus:~# netstat -rn
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt
Iface
10.0.0.202      10.0.0.150      255.255.255.255 UGH       0 0          0
tap0
10.0.0.201      10.0.0.150      255.255.255.255 UGH       0 0          0
tap0
10.0.0.0        0.0.0.0         255.0.0.0       U         0 0          0
eth0
10.0.0.0        0.0.0.0         255.0.0.0       U         0 0          0
tap0
0.0.0.0         10.0.0.254      0.0.0.0         UG        0 0          0
eth0


---------------------------------------------------------------------------
"When a man sits with a pretty girl for an hour, it seems like a minute.
But let him sit on a hot stove for a minute and it''s longer than any
hour.
That''s relativity." [A. Einstein, 1938]


_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Jurgen Stroo

2005-Jun-05 15:48 UTC

head link

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

No one on this?


Although very unlikely, it seems Jurgen Stroo stated on Jun 5 that :
> Hi list.
>
> I started with Xen yesterday, but I am facing a bit of a problem.
> My system had always configure eth0 with 10.0.0.4/8
>
> I am using Xen unstable source (on Debian sid)
>
> Now I installed Xen, rebooted the machine, and first the usual network is
> coming up and then the xend will be started.
>
> I''ll end up with this, but I am wondering if this should be the
way of
> things to be configured:
>
> megalosaurus:~# ifconfig -a
> eth0      Link encap:Ethernet  HWaddr 00:40:63:D7:A3:82
>           inet addr:10.0.0.4  Bcast:10.255.255.255  Mask:255.0.0.0
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:807379 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:680984 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:174 txqueuelen:1000
>           RX bytes:800654135 (763.5 MiB)  TX bytes:52893851 (50.4 MiB)
>           Interrupt:11 Base address:0xec00
>
> lo        Link encap:Local Loopback
>           inet addr:127.0.0.1  Mask:255.0.0.0
>           UP LOOPBACK RUNNING  MTU:16436  Metric:1
>           RX packets:19 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:19 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:0
>           RX bytes:2004 (1.9 KiB)  TX bytes:2004 (1.9 KiB)
>
> tap0      Link encap:Ethernet  HWaddr EE:F6:D7:D8:F4:F8
>           inet addr:10.0.0.150  Bcast:10.255.255.255  Mask:255.0.0.0
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:21 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:500
>           RX bytes:0 (0.0 b)  TX bytes:882 (882.0 b)
>
> veth0     Link encap:Ethernet  HWaddr 00:40:63:D7:A3:82
>           inet addr:10.0.0.4  Bcast:10.255.255.255  Mask:255.0.0.0
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:120 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:0
>           RX bytes:0 (0.0 b)  TX bytes:32280 (31.5 KiB)
>
> vif0.0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
>           BROADCAST MULTICAST  MTU:1500  Metric:1
>           RX packets:120 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:0
>           RX bytes:32280 (31.5 KiB)  TX bytes:0 (0.0 b)
>
> xen-br0   Link encap:Ethernet  HWaddr 00:00:00:00:00:00
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:0
>           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
>
> After the system boots and the network and xend is started, nothing works,
> with this configuration.
>
> Actually, it works now after restarting the network
> (/etc/init.d/networking) and after restarting xend (sometimes a couple of
> times though)
>
> I can''t find anywhere in the docs if eth0 should be configured
like this.
> Sometimes I am experiencing lots of lag, as if these IP''s are
conflicting with
> each other.
>
> The whole networking thing seems not to be configured right.
>
> for completeness:
>
> megalosaurus:~# netstat -rn
> Kernel IP routing table
> Destination     Gateway         Genmask         Flags   MSS Window  irtt
> Iface
> 10.0.0.202      10.0.0.150      255.255.255.255 UGH       0 0          0
> tap0
> 10.0.0.201      10.0.0.150      255.255.255.255 UGH       0 0          0
> tap0
> 10.0.0.0        0.0.0.0         255.0.0.0       U         0 0          0
> eth0
> 10.0.0.0        0.0.0.0         255.0.0.0       U         0 0          0
> tap0
> 0.0.0.0         10.0.0.254      0.0.0.0         UG        0 0          0
> eth0
>
>
> ---------------------------------------------------------------------------
> "When a man sits with a pretty girl for an hour, it seems like a
minute.
> But let him sit on a hot stove for a minute and it''s longer than
any hour.
> That''s relativity." [A. Einstein, 1938]
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
>
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Ian Pratt

2005-Jun-05 16:32 UTC

head link

RE: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

> No one on this?
The /etc/xen/scripts/network script should be creating the bridge and
veth0, and transferring the IP address from eth0 to veth0.

It appears in your report as though both eth0 and veth0 have the same
address. I expect this is a conflict between the network script and your
existing setup.

Ian 
 > Although very unlikely, it seems Jurgen Stroo stated on Jun 5 that :
> 
> > Hi list.
> >
> > I started with Xen yesterday, but I am facing a bit of a problem.
> > My system had always configure eth0 with 10.0.0.4/8
> >
> > I am using Xen unstable source (on Debian sid)
> >
> > Now I installed Xen, rebooted the machine, and first the 
> usual network 
> > is coming up and then the xend will be started.
> >
> > I''ll end up with this, but I am wondering if this should be 
> the way of 
> > things to be configured:
> >
> > megalosaurus:~# ifconfig -a
> > eth0      Link encap:Ethernet  HWaddr 00:40:63:D7:A3:82
> >           inet addr:10.0.0.4  Bcast:10.255.255.255  Mask:255.0.0.0
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
> >           RX packets:807379 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:680984 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:174 txqueuelen:1000
> >           RX bytes:800654135 (763.5 MiB)  TX bytes:52893851 
> (50.4 MiB)
> >           Interrupt:11 Base address:0xec00
> >
> > lo        Link encap:Local Loopback
> >           inet addr:127.0.0.1  Mask:255.0.0.0
> >           UP LOOPBACK RUNNING  MTU:16436  Metric:1
> >           RX packets:19 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:19 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:0
> >           RX bytes:2004 (1.9 KiB)  TX bytes:2004 (1.9 KiB)
> >
> > tap0      Link encap:Ethernet  HWaddr EE:F6:D7:D8:F4:F8
> >           inet addr:10.0.0.150  Bcast:10.255.255.255  Mask:255.0.0.0
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
> >           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:21 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:500
> >           RX bytes:0 (0.0 b)  TX bytes:882 (882.0 b)
> >
> > veth0     Link encap:Ethernet  HWaddr 00:40:63:D7:A3:82
> >           inet addr:10.0.0.4  Bcast:10.255.255.255  Mask:255.0.0.0
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
> >           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:120 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:0
> >           RX bytes:0 (0.0 b)  TX bytes:32280 (31.5 KiB)
> >
> > vif0.0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
> >           BROADCAST MULTICAST  MTU:1500  Metric:1
> >           RX packets:120 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:0
> >           RX bytes:32280 (31.5 KiB)  TX bytes:0 (0.0 b)
> >
> > xen-br0   Link encap:Ethernet  HWaddr 00:00:00:00:00:00
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
> >           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:0
> >           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
> >
> > After the system boots and the network and xend is started, nothing 
> > works, with this configuration.
> >
> > Actually, it works now after restarting the network
> > (/etc/init.d/networking) and after restarting xend 
> (sometimes a couple 
> > of times though)
> >
> > I can''t find anywhere in the docs if eth0 should be 
> configured like this.
> > Sometimes I am experiencing lots of lag, as if these IP''s are
> > conflicting with each other.
> >
> > The whole networking thing seems not to be configured right.
> >
> > for completeness:
> >
> > megalosaurus:~# netstat -rn
> > Kernel IP routing table
> > Destination     Gateway         Genmask         Flags   MSS 
> Window  irtt
> > Iface
> > 10.0.0.202      10.0.0.150      255.255.255.255 UGH       0 
> 0          0
> > tap0
> > 10.0.0.201      10.0.0.150      255.255.255.255 UGH       0 
> 0          0
> > tap0
> > 10.0.0.0        0.0.0.0         255.0.0.0       U         0 
> 0          0
> > eth0
> > 10.0.0.0        0.0.0.0         255.0.0.0       U         0 
> 0          0
> > tap0
> > 0.0.0.0         10.0.0.254      0.0.0.0         UG        0 
> 0          0
> > eth0
> >
> >
> > 
> ----------------------------------------------------------------------
> > ----- "When a man sits with a pretty girl for an hour, it 
> seems like a 
> > minute.
> > But let him sit on a hot stove for a minute and it''s longer 
> than any hour.
> > That''s relativity." [A. Einstein, 1938]
> >
> >
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > http://lists.xensource.com/xen-devel
> >
> 
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
> 
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Keir Fraser

2005-Jun-05 16:40 UTC

head link

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

On 5 Jun 2005, at 17:32, Ian Pratt wrote:
> The /etc/xen/scripts/network script should be creating the bridge and
> veth0, and transferring the IP address from eth0 to veth0.
>
> It appears in your report as though both eth0 and veth0 have the same
> address. I expect this is a conflict between the network script and 
> your
> existing setup.
The script does not bother to delete the address from the old 
interface, but the routes should be changed to be via veth0 rather than 
eth0.

  -- Keir


_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Keir Fraser

2005-Jun-05 16:47 UTC

head link

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

On 5 Jun 2005, at 17:40, Keir Fraser wrote:
>> The /etc/xen/scripts/network script should be creating the bridge and
>> veth0, and transferring the IP address from eth0 to veth0.
>>
>> It appears in your report as though both eth0 and veth0 have the same
>> address. I expect this is a conflict between the network script and 
>> your
>> existing setup.
>
> The script does not bother to delete the address from the old 
> interface, but the routes should be changed to be via veth0 rather 
> than eth0.
Hmm.. actually the script *is* supposed to delete the address from 
eth0. So I''m not sure how things ended up in the state Jurgen posted.

  -- Keir


_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Jurgen Stroo

2005-Jun-05 20:53 UTC

head link

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Hi,

Actually, I checked this script indeed, and also did by hand what I
thought should happen, the takeover of the MAC and IP of eth0 and transfer
it to de veth0. What I did was setting the MAC address to a plain
FE:FF:FF:FF:FF:FF MAC address, and deleted the IP address, after these
were taken over by veth0.

But, as Keir correctly stated, the routes should also be redefined, hence
eth0 is disabled.

Also, when I boot, and I do not use ''xend start'' but do the
/etc/xen/scripts/network start instead, the IP take-over process is done
correctly. So I''ll check why this isn''t working via xend start
later.

The thing is, after I''ve got the following configuration it is still
-NOT-
working:

megalosaurus:~# ifconfig -a
eth0      Link encap:Ethernet  HWaddr FF:FF:FF:FF:FF:FF
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:20 errors:0 dropped:0 overruns:0 frame:0
          TX packets:86 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1956 (1.9 KiB)  TX bytes:12490 (12.1 KiB)
          Interrupt:11 Base address:0xec00

<..snip..>

veth0     Link encap:Ethernet  HWaddr 00:40:63:D7:A3:82
          inet addr:10.0.0.4  Bcast:10.255.255.255  Mask:255.0.0.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:21 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:882 (882.0 b)

megalosaurus:~#
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt
Iface
10.0.0.0        0.0.0.0         255.0.0.0       U         0 0          0
veth0
0.0.0.0         10.0.0.254      0.0.0.0         UG        0 0          0
veth0

megalosaurus:~# iptables -L
Chain INPUT (policy ACCEPT)
target     prot opt source               destination

Chain FORWARD (policy DROP)
target     prot opt source               destination

Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination


So, this looks good IMHO, but it does not work.
Some checking with tcpdump on the Xen host (10.0.0.4) gave me the
following remarkable info:


04:41:30.508617 arp who-has 10.0.0.3 tell newmeg
04:41:30.508763 arp reply 10.0.0.3 is-at 00:01:02:0a:25:0d


And, I saw on this 10.0.0.3 (oldserver) host:

20:44:00.289199 arp who-has oldserver tell 10.0.0.4

They are getting each others arp replies!
So, these two servers actually *see* each other, but they won''t come
much
further than arp, ip (as in the protocol) is not working...

PS
When stopping the xen network and thus the bridge, and restart my default
debian network configuration, everything works again..

I am really scratching my head now.

Jurgen


Although very unlikely, it seems Keir Fraser stated on Jun 5 that :
>
> On 5 Jun 2005, at 17:40, Keir Fraser wrote:
>
> >> The /etc/xen/scripts/network script should be creating the bridge
and
> >> veth0, and transferring the IP address from eth0 to veth0.
> >>
> >> It appears in your report as though both eth0 and veth0 have the
same
> >> address. I expect this is a conflict between the network script
and
> >> your
> >> existing setup.
> >
> > The script does not bother to delete the address from the old
> > interface, but the routes should be changed to be via veth0 rather
> > than eth0.
>
> Hmm.. actually the script *is* supposed to delete the address from
> eth0. So I''m not sure how things ended up in the state Jurgen
posted.
>
>   -- Keir
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
>
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Keir Fraser

2005-Jun-06 08:14 UTC

head link

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

On 5 Jun 2005, at 21:53, Jurgen Stroo wrote:
>
> The thing is, after I''ve got the following configuration it is
still
> -NOT-
> working:
>
> megalosaurus:~# ifconfig -a
> eth0      Link encap:Ethernet  HWaddr FF:FF:FF:FF:FF:FF
The MAC address should be FE:FF:FF:FF:FF:FF. The one above is the 
broadcast address. Not sure if it actually matters, but worth fixing 
anyway as it might confuse the bridge.

I had problems with ARP when I first started testing veth0. It turned 
out that domain0 was not applying the information in ARP packets to the 
ARP cache. Since the ARP cache wasn''t kept up to date, I saw very weird
IP behaviour.

I fixed that particular bug, but maybe there''s another one. It is 
perhaps worth looking at /proc/net/arp and seeing how it compares with 
other machines on your network.

  -- Keir

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Jurgen Stroo

2005-Jun-09 08:50 UTC

head link

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Hi Keir, and others, I didn''t have time last week to further
investigate
the problem, but I''m able to do now.

When I do the network scripts by hand, as I already mentioned,
things are going well and the interface and routing configuration are
okay. this means correct routes via veth0 etc. Also eth0 got its
FE:FF:FF:FF:FF:FF correctly.

The arp table looks good actually:

normal situation without xen:
megalosaurus:~# cat /proc/net/arp
IP address       HW type     Flags       HW address            Mask
Device
10.0.0.3         0x1         0x2         00:01:02:0A:25:0D     *
eth0
10.0.0.142       0x1         0x0         00:00:00:00:00:00     *
eth0
10.0.0.141       0x1         0x0         00:00:00:00:00:00     *
eth0
10.0.0.254       0x1         0x2         00:13:49:10:0B:E0     *
eth0

And with Xen and the veth0 interface:
IP address       HW type     Flags       HW address            Mask
Device
10.0.0.141       0x1         0x0         00:00:00:00:00:00     *
veth0
10.0.0.142       0x1         0x0         00:00:00:00:00:00     *
veth0
10.0.0.3         0x1         0x2         00:01:02:0A:25:0D     *
veth0
10.0.0.254       0x1         0x2         00:13:49:10:0B:E0     *
veth0


Looks perfectly right, I don''t know what the problem could be actually.
Everyting looks right and they reply to each others arp requests, that
means on ARP level they see each other and reply to each other with the
ARP replies.

:-S
Jurgen


Although very unlikely, it seems Keir Fraser stated on Jun 6 that :
>
> On 5 Jun 2005, at 21:53, Jurgen Stroo wrote:
>
> >
> > The thing is, after I''ve got the following configuration it
is still
> > -NOT-
> > working:
> >
> > megalosaurus:~# ifconfig -a
> > eth0      Link encap:Ethernet  HWaddr FF:FF:FF:FF:FF:FF
>
> The MAC address should be FE:FF:FF:FF:FF:FF. The one above is the
> broadcast address. Not sure if it actually matters, but worth fixing
> anyway as it might confuse the bridge.
>
> I had problems with ARP when I first started testing veth0. It turned
> out that domain0 was not applying the information in ARP packets to the
> ARP cache. Since the ARP cache wasn''t kept up to date, I saw very
weird
> IP behaviour.
>
> I fixed that particular bug, but maybe there''s another one. It is
> perhaps worth looking at /proc/net/arp and seeing how it compares with
> other machines on your network.
>
>   -- Keir
>
>
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Apparently Analagous Threads

Search for more seemingly similar threads

Xen devel - Jun 2005 - Xen 3.0 Xend loses network - eth0 -> veth0?

[Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

RE: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Re: [Xen-devel] Xen 3.0 Xend loses network - eth0 -> veth0?

Apparently Analagous Threads