hello.
i just installed xen from source (using mke world then make install) booted
into linux using the xen-2.0.7.gz kernel and then triewd to run ttylinux
from the instructions in the user manual.
i used this command.
xm create /store/xmexample1 -c
my xonfigfile ( xmexample1) is this.
> # -*- mode: python; -*-
>
>
#===========================================================================>
# Python configuration setup for ''xm create''.
> # This script sets the parameters used when a domain is created using
''xm
> create''.
> # You use a separate script for each domain you want to create, or
> # you can set the parameters for the domain on the xm command line.
>
>
#===========================================================================>
>
>
#----------------------------------------------------------------------------
> # Kernel image file.
> kernel = "/boot/vmlinuz-2.6.11-xenU"
>
> # Optional ramdisk.
> #ramdisk = "/boot/initrd.gz"
>
> # The domain build function. Default is ''linux''.
> #builder=''linux''
>
> # Initial memory allocation (in megabytes) for the new domain.
> memory = 10
>
> # A name for your domain. All domains must have different names.
> name = "ttylinux"
>
> # Which CPU to start domain on?
> #cpu = -1 # leave to Xen to pick
>
>
>
#----------------------------------------------------------------------------
> # Define network interfaces.
>
> # Number of network interfaces. Default is 1.
> nics=1
>
> # Optionally define mac and/or bridge for the network interfaces.
> # Random MACs are assigned if not given.
> #vif = [ ''mac=aa:00:00:00:00:11, bridge=xen-br0'' ]
>
>
>
#----------------------------------------------------------------------------
> # Define the disk devices you want the domain to have access to, and
> # what you want them accessible as.
> # Each disk entry is of the form phy:UNAME,DEV,MODE
> # where UNAME is the device, DEV is the device name the domain will see,
> # and MODE is r for read-only, w for read-write.
>
> disk = [ ''file:/home/m/Desktop/ttylinux-
> 4.9_2.tar.gz_FILES/ttylinux-4.9/rootfs.gz,sda1,rw'' ]
> #disk = [ ''phy:s1-lvol0,swap,w'' ]
>
>
#----------------------------------------------------------------------------
> # Set the kernel command line for the new domain.
> # You only need to define the IP parameters and hostname if the
domain''s
> # IP config doesn''t, e.g. in ifcfg-eth0 or via DHCP.
> # You can use ''extra'' to set the runlevel and custom
environment
> # variables used by custom rc scripts (e.g. VMID=, usr= ).
>
> # Set if you want dhcp to allocate the IP address.
> #dhcp="dhcp"
> # Set netmask.
> #netmask> # Set default gateway.
> #gateway> # Set the hostname.
> #hostname= "vm%d" % vmid
> ip = "1.2.3.4"
>
> # Set root device.
> rootpath = "/dev/sda1 ro"
>
> # Root device for nfs.
> #root = "/dev/nfs"
> # The nfs server.
> #nfs_server = ''169.254.1.0''
> # Root directory on the nfs server.
> #nfs_root = ''/full/path/to/root/directory''
>
> # Sets runlevel 4.
> extra = "4"
>
>
>
#----------------------------------------------------------------------------
> # Set according to whether you want the domain restarted when it exits.
> # The default is ''onreboot'', which restarts the domain
when it shuts down
> # with exit code reboot.
> # Other values are ''always'', and
''never''.
>
> restart = ''never''
>
>
>
#===========================================================================
now upon running the command i get this output and then it stops. nothing
happens after this.
please tell what i am doing wrong. i am a noob at this so please help.
m@ubuntu:/store$ xm create /store/xmexample1 -c> Using config file "/store/xmexample1".
> Started domain ttylinux, console on port 9620
> ************ REMOTE CONSOLE: CTRL-] TO QUIT ********
> Linux version 2.6.11.12-xenU (m@ubuntu) (gcc version 3.3.5 (Debian 1:
> 3.3.5-8ubuntu2)) #1 Sat Nov 26 17:41:04 PKT 2005
> BIOS-provided physical RAM map:
> Xen: 0000000000000000 - 0000000000a00000 (usable)
> 10MB LOWMEM available.
> DMI not present.
> IRQ lockup detection disabled
> Allocating PCI resources starting at 00a00000 (gap: 00a00000:ff600000)
> Built 1 zonelists
> Kernel command line: ip=1.2.3.4:1.2.3.4::::eth0:off 4
> Initializing CPU#0
> PID hash table entries: 64 (order: 6, 1024 bytes)
> Xen reported: 1666.557 MHz processor.
> Using tsc for high-res timesource
> Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
> Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
> vmalloc area: c1800000-fbff9000, maxmem 34000000
> Memory: 7760k/10240k available (1631k kernel code, 2456k reserved, 439k
> data, 112k init, 0k highmem)
> Checking if this processor honours the WP bit even in supervisor mode...
> Ok.
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> CPU: CLK_CTL MSR was 0. Reprogramming to 20000000
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 256K (64 bytes/line)
> CPU: AMD Sempron(tm) 2400+ stepping 01
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking ''hlt'' instruction... disabled
> NET: Registered protocol family 16
> xen_mem: Initialising balloon driver.
> Initializing Cryptographic API
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> Xen virtual console successfully installed as tty
> Event-channel device installed.
> xen_blk: Initialising virtual block device driver
> xen_net: Initialising virtual ethernet driver.
> NET: Registered protocol family 2
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP established hash table entries: 512 (order: 0, 4096 bytes)
> TCP bind hash table entries: 512 (order: -1, 2048 bytes)
> TCP: Hash tables configured (established 512 bind 512)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> IP-Config: Guessing netmask 255.0.0.0
> IP-Config: Complete:
> device=eth0, addr=1.2.3.4, mask=255.0.0.0, gw=255.255.255.255,
nothing happens after this.
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users
