Rushabh Sanghavi (Rush)
2025-Jan-31 03:50 UTC
[Nut-upsdev] Error "Data for UPS [pcmusb] is stale - check driver"
Dear NUT Developers, A very good morning to you and hope that you are in the best of health and spirits. For an upcoming UPS Project, our team has been testing Powercom?s Cleanline T-1500 UPS model whose photo has been attached with this e-mail. Our team has been testing this UPS with one of our 4G LTE WiFi router models on which Network UPS Tools (NUT) Version 2.8.0-3 has been installed. BUT during the testing our team observed multiple instances of error message "Data for UPS [pcmusb] is stale - check driver" being randomly reported by our 4G LTE WiFi router. Here is the SUMMARY of the issue below for clear understanding purposes. * NUT Version 2.8.0-3 was installed on our 4G LTE WiFi router by our team. * Also our 4G LTE WiFi router had Linux Kernel Version 5.15.127, OpenWRT Distribution release ?23.05.0-rc3? and OpenWRT Distribution Revision ?r23389-5deed175a5? installed on it. * Powercom?s Cleanline T-1500 UPS was connected with our 4G LTE WiFi router via USB to USB Cable Connection (i.e. USB Port on router side and USB Port on UPS side) Now when NUT installed on our 4G LTE WiFi router model unit tried to poll and fetch values of different UPS parameters from Powercom?s Cleanline T-1500 UPS model after both UPS and router had been running for sometime (i.e. for random period of time): * router started reporting the error message ?Data for UPS [pcmusb] is stale - check driver? * after that router could not get UPS?s status any more unless we restart the NUT service * and the router started reporting the error message ?Data for UPS [pcmusb] is stale - check driver? after running for sometime again Note: [pcmusb] represents the name or identifier assigned to the UPS instance within the NUT (Network UPS Tools) configuration * Our team tried to increase value of NUT?s timers such as ?pollinterval?, ?pollfreq?, ?maxage? but still the issue could not get solved or fixed * Kindly NOTE that our team tested the above with both the NUT Drivers i.e. blazer_usb and nutdrv_qx. But the same error message mentioned above was observed. * Also kindly NOTE that our team also tried to test with NUT Driver ?usbhid-ups? but it is seems that this particular Driver is not supported by Powercom?s Cleanline T-1500 UPS model whose photo has been attached with this e-mail. * Currently our team is not 100% sure about the exact root cause. Our team need to know the following from NUT Developers. * Which the is correct NUT Driver that our team need to use on the 4G LTE WiFi router so that it can communicate smoothly and successfully with Powercom?s Cleanline T-1500 UPS model whose photo has been attached with this e-mail? * Which specific parameters within the default Configuration Settings file of NUT Version 2.8.0-3 on our 4G LTE WiFi router need to be tweaked / changed so that our 4G LTE WiFi router model can communicate with the Powercom?s Cleanline T-1500 UPS model smoothly and successfully? * Which specific parameters within the default ups.conf / upsd.conf file on our 4G LTE WiFi router needs to be tweaked / changed so that our 4G LTE WiFi router model can communicate with the Powercom?s Cleanline T-1500 UPS model smoothly and successfully? Also I am hereby attaching the Log Files with the Log Messages reported on our 4G LTE WiFi router model. The 1st Log file contains Log Messages during testing with NUT Driver ?blazer_usb? while the 2nd Log file contains Log Messages during testing with NUT Driver ?nutdrv_qx?. You will observe the ERROR Message ?Data for UPS [pcmusb] is stale - check driver? within both these attached Log Files. Awaiting your swift response back. Thanking you, Yours sincerely, [Legs Logo] Rushabh N. S Research and Development Director PP Ontime Company Limited PP Group of Companies Address: 1011 Supalai Grand Tower, 16th Floor, Rama 3 Road, Chongnonsi, Yannawa, Bangkok ? 10120, Thailand Landline No: +66-2-0562099 Ext. 2201 Fax No: +66-2-0562088 Cell Phone No: +66-8-59118578 / +66-6-22236221 E-mail: rushabh at pp-ontime.co.th<mailto:rushabh at pp-ontime.co.th> Web: www.pp-ontime.co.th<http://www.pp-ontime.co.th> Skype ID: rushabh.sanghavi Disclaimer: *************************************************************** Important Confidentiality: This Information is intended for the above-named person and may contain confidential and/or legally privileged material. Any opinions expressed in this information are not necessarily those of the company. If it has come to you in error you must take no action based on it, nor must you copy or show it to anyone; please delete/destroy and inform the sender immediately. Monitoring/Viruses/Malwares PP-Ontime reserves the right to monitor all incoming and outgoing emails via PP-Ontime's systems. Although we have security program to monitor and eliminate virus/malware, we also advise that in keeping with good computing practice the recipient should ensure they are actually virus/malwares free. *************************************************************** Disclaimer: *********************************************************************************************** Important Confidentiality: This Information is intended for the above-named person and may contain confidential and/or legally privileged material. Any opinions expressed in this information are not necessarily those of the company. If it has come to you in error you must take no action based on it, nor must you copy or show it to anyone; please delete/destroy and inform the sender immediately. Monitoring/Viruses/Malwares PP-Ontime reserves the right to monitor all incoming and outgoing emails via PP-Ontime's systems. Although we have security program to monitor and eliminate virus/malware, we also advise that in keeping with good computing practice the recipient should ensure they are actually virus/malwares free. ********************************************************************************************** -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://alioth-lists.debian.net/pipermail/nut-upsdev/attachments/20250131/6c7c01fa/attachment-0001.htm> -------------- next part -------------- A non-text attachment was scrubbed... Name: image001.jpg Type: image/jpeg Size: 4031 bytes Desc: image001.jpg URL: <http://alioth-lists.debian.net/pipermail/nut-upsdev/attachments/20250131/6c7c01fa/attachment-0001.jpg> -------------- next part -------------- A non-text attachment was scrubbed... Name: Powercom?s Cleanline T-1500 UPS model.png Type: image/png Size: 1720860 bytes Desc: Powercom?s Cleanline T-1500 UPS model.png URL: <http://alioth-lists.debian.net/pipermail/nut-upsdev/attachments/20250131/6c7c01fa/attachment-0001.png> -------------- next part -------------- 2023-08-19T21:01:23.000000+07:00 PPL404I-112 boot[1062] ********************* PWR logger-Power Up(syslog) ******************* 2023-08-19T21:02:09.899836+07:00 PPL404I-112 : [origin software="rsyslogd" swVersion="8.2110.0" x-pid="3237" x-info="https://www.rsyslog.com"] start 2023-08-19T21:02:17.574925+07:00 PPL404I-112 netifd: Interface 'lan' is enabled 2023-08-19T21:02:17.593870+07:00 PPL404I-112 netifd: Interface 'lan' is now up 2023-08-19T21:02:17.750734+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T21:02:17.754789+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T21:02:18.319623+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T21:02:18.322773+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T21:02:18.335565+07:00 PPL404I-112 netifd: Interface 'loopback' is enabled 2023-08-19T21:02:18.349058+07:00 PPL404I-112 netifd: Interface 'loopback' is now up 2023-08-19T21:02:18.469042+07:00 PPL404I-112 netifd: Interface 'loopback' has link connectivity 2023-08-19T21:03:01.076794+07:00 PPL404I-112 mount_root: performing overlay whiteout 2023-08-19T21:03:01.094361+07:00 PPL404I-112 mount_root: synchronizing overlay 2023-08-19T21:03:03.823783+07:00 PPL404I-112 mount_root: failed to sync jffs2 overlay 2023-08-19T21:03:04.026889+07:00 PPL404I-112 procd: /etc/rc.d/S96led: setting up led lan4 2023-08-19T21:03:04.057303+07:00 PPL404I-112 procd: /etc/rc.d/S96led: setting up led lan3 2023-08-19T21:03:04.087544+07:00 PPL404I-112 procd: /etc/rc.d/S96led: setting up led lan2 2023-08-19T21:03:04.117803+07:00 PPL404I-112 procd: /etc/rc.d/S96led: setting up led lan1 2023-08-19T21:03:04.147972+07:00 PPL404I-112 procd: /etc/rc.d/S96led: setting up led wan 2023-08-19T21:03:06.866795+07:00 PPL404I-112 root: /opt/pp/CLI/sbin/pre_zl502.sh 2023-08-19T21:03:07.243849+07:00 PPL404I-112 urandom_seed[3920]: Seed saved (/etc/urandom.seed) 2023-08-19T21:03:14.496260+07:00 PPL404I-112 root: service QoS Stop ... 2023-08-19T21:03:15.129140+07:00 PPL404I-112 root: [serial_upsd]...Stopped 2023-08-19T21:03:16.777914+07:00 PPL404I-112 root: [usb_upsd]...Stopped 2023-08-19T21:03:22.542857+07:00 PPL404I-112 : [origin software="rsyslogd" swVersion="8.2110.0" x-pid="4716" x-info="https://www.rsyslog.com"] start 2023-08-19T21:03:22.698596+07:00 PPL404I-112 root: /opt/pp/CLI/sbin/post_zl502.sh 2023-08-19T21:03:23.154963+07:00 PPL404I-112 root: service iptables Stop ... 2023-08-19T21:03:29.426692+07:00 PPL404I-112 root: service QoS Stop ... 2023-08-19T21:03:29.787026+07:00 PPL404I-112 dropbear[5350]: Child connection from 192.168.99.55:60607 2023-08-19T21:03:30.284885+07:00 PPL404I-112 root: [serial_upsd]...Stopped 2023-08-19T21:03:31.287002+07:00 PPL404I-112 procd: - init complete - 2023-08-19T21:03:33.712275+07:00 PPL404I-112 root: [usb_upsd]...Stopped 2023-08-19T21:03:36.263326+07:00 PPL404I-112 root: service iptables Stop ... 2023-08-19T21:03:37.649082+07:00 PPL404I-112 root: service iptables Starting ... 2023-08-19T21:03:46.873776+07:00 PPL404I-112 dropbear[5350]: Password auth succeeded for 'admin' from 192.168.99.55:60607 2023-08-19T21:03:54.061711+07:00 PPL404I-112 CLI-admin[5350]: CLI 2023-08-19T21:03:54.696588+07:00 PPL404I-112 CLI-admin[5350]: CLI/status 2023-08-19T21:05:29.372934+07:00 PPL404I-112 CLI-admin[5350]: CLI/status/exit 2023-08-19T21:05:29.375523+07:00 PPL404I-112 CLI-admin[5350]: CLI 2023-08-19T21:05:29.850637+07:00 PPL404I-112 CLI-admin[5350]: CLI/config 2023-08-19T21:05:30.137665+07:00 PPL404I-112 CLI-admin[5350]: CLI/config/cli_upload 2023-08-19T21:05:32.793551+07:00 PPL404I-112 CLI-admin[5350]: CLI/config/write_config 2023-08-19T21:05:32.886342+07:00 PPL404I-112 root: CLI-admin[5350]:CLI/config/write_config_CHANGE:cli.startup.disableservice=agentd squid usb_upsd serial_upsd log xl2tpd dnsmasq keepalived odhcpd qos dot1x -> agentd squid serial_upsd log xl2tpd dnsmasq keepalived odhcpd qos dot1x 2023-08-19T21:05:32.933318+07:00 PPL404I-112 root: CLI-admin[5350]:CLI/config/write_config_CHANGE:cli.startup.enableservice=iptables -> iptables usb_upsd 2023-08-19T21:05:32.970008+07:00 PPL404I-112 root: CLI-admin[5350]:CLI/config/write_config_CHANGE:cli.startup.stop_as_reboot=iptables -> squid 2023-08-19T21:05:33.424122+07:00 PPL404I-112 CLI-admin[5350]: CLI/config/save_running_2flash 2023-08-19T21:05:34.293325+07:00 PPL404I-112 CLI-admin[5350]: CLI/config/exit 2023-08-19T21:05:34.295916+07:00 PPL404I-112 CLI-admin[5350]: CLI 2023-08-19T21:05:34.610059+07:00 PPL404I-112 CLI-admin[5350]: CLI/status 2023-08-19T21:05:35.653877+07:00 PPL404I-112 CLI-admin[5350]: CLI/status/reboot 2023-08-19T21:05:35.689666+07:00 PPL404I-112 procd: - shutdown - 2023-08-19T21:05:36.885986+07:00 PPL404I-112 reboot[7701]: ********************* logger-Reboot/Power Down ******************* 2023-08-19T21:05:49.000000+07:00 PPL404I-112 boot[871] ********************* PWR logger-Power Up(syslog) ******************* 2023-08-19T21:06:19.867329+07:00 PPL404I-112 : [origin software="rsyslogd" swVersion="8.2110.0" x-pid="2502" x-info="https://www.rsyslog.com"] start 2023-08-19T21:06:24.262509+07:00 PPL404I-112 root: /opt/pp/CLI/sbin/pre_zl502.sh 2023-08-19T21:06:29.162773+07:00 PPL404I-112 root: service QoS Stop ... 2023-08-19T21:06:29.676175+07:00 PPL404I-112 root: [serial_upsd]...Stopped 2023-08-19T21:06:30.730386+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN4 link down 2023-08-19T21:06:31.000326+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN3 link down 2023-08-19T21:06:31.231559+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2023-08-19T21:06:31.470125+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN1 link up 2023-08-19T21:06:31.622387+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: wan link down 2023-08-19T21:06:33.190110+07:00 PPL404I-112 root: /opt/pp/CLI/sbin/post_zl502.sh 2023-08-19T21:06:34.731948+07:00 PPL404I-112 root: service iptables Stop ... 2023-08-19T21:06:40.630388+07:00 PPL404I-112 root: service QoS Stop ... 2023-08-19T21:06:40.761775+07:00 PPL404I-112 procd: - init complete - 2023-08-19T21:06:42.384718+07:00 PPL404I-112 root: [serial_upsd]...Stopped 2023-08-19T21:06:45.142091+07:00 PPL404I-112 root: [usb_upsd]...Stopped 2023-08-19T21:06:45.547068+07:00 PPL404I-112 root: service iptables Stop ... 2023-08-19T21:06:46.934705+07:00 PPL404I-112 root: service iptables Starting ... 2023-08-19T21:06:53.378196+07:00 PPL404I-112 netifd: Interface 'lan' is enabled 2023-08-19T21:06:53.392948+07:00 PPL404I-112 netifd: Interface 'lan' is now up 2023-08-19T21:06:53.796553+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T21:06:53.800564+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T21:06:54.072630+07:00 PPL404I-112 root: [nut-server-usb]...Stopped 2023-08-19T21:06:54.322793+07:00 PPL404I-112 root: [usb_upsd]...Started 2023-08-19T21:06:54.336915+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T21:06:54.340190+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T21:06:54.353951+07:00 PPL404I-112 netifd: Interface 'loopback' is enabled 2023-08-19T21:06:54.360262+07:00 PPL404I-112 netifd: Interface 'loopback' is now up 2023-08-19T21:06:54.585251+07:00 PPL404I-112 netifd: Interface 'loopback' has link connectivity 2023-08-19T21:07:04.408292+07:00 PPL404I-112 root: [nut-server-usb]...Stopped 2023-08-19T21:07:06.111381+07:00 PPL404I-112 upsd-usbd[5208]: listening on 127.0.0.1 port 6490 2023-08-19T21:07:06.290139+07:00 PPL404I-112 root: [nut-server-usb]...Started 2023-08-19T21:07:06.292024+07:00 PPL404I-112 upsd-usbd[5209]: Startup successful 2023-08-19T21:07:16.759065+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2023-08-19T21:07:19.840070+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:2/3 2023-08-19T21:07:20.858567+07:00 PPL404I-112 dropbear[5431]: Child connection from 192.168.99.55:61559 2023-08-19T21:07:22.957189+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:3/3 2023-08-19T21:07:23.612976+07:00 PPL404I-112 dropbear[5431]: Password auth succeeded for 'admin' from 192.168.99.55:61559 2023-08-19T21:07:26.044023+07:00 PPL404I-112 u_main.pl: Uupsd:COMMUNICATION LOST-pls. check ups's connection 2023-08-19T21:07:26.675208+07:00 PPL404I-112 u_main.pl: Uupsd:Start-Service:AC-Status=0:UPS-Status=:Manual-Shutdown=1:Beeper=enabled 2023-08-19T21:07:26.815726+07:00 PPL404I-112 u_main.pl: Uupsd:UPS-Beeper=>Enable 2023-08-19T21:07:28.964514+07:00 PPL404I-112 hu_sys.pl: Uupsd:Syslog_Interval=300 2023-08-19T21:07:35.156364+07:00 PPL404I-112 CLI-admin[5431]: CLI 2023-08-19T21:07:35.780644+07:00 PPL404I-112 CLI-admin[5431]: CLI/status 2023-08-19T21:07:37.519594+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/log0_trace -n 205 2023-08-19T21:08:00.150894+07:00 PPL404I-112 crond[2639]: USER root pid 6876 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2023-08-19T21:08:07.171723+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2023-08-19T21:08:08.322779+07:00 PPL404I-112 blazer_usb[7375]: Please note that this driver is deprecated and will not receive#012new development. If it works for managing your devices - fine,#012but if you are running it to try setting up a new device, please#012consider the newer nutdrv_qx instead, which should handle all 'Qx'#012protocol variants for NUT. (Please also report if your device works#012with this driver, but nutdrv_qx would not actually support it with#012any subdriver!) 2023-08-19T21:08:08.573995+07:00 PPL404I-112 blazer_usb[7375]: Supported UPS detected with megatec protocol 2023-08-19T21:08:08.885592+07:00 PPL404I-112 blazer_usb[7375]: Vendor information read in 1 tries 2023-08-19T21:08:09.141577+07:00 PPL404I-112 blazer_usb[7375]: Warning information read in 1 tries 2023-08-19T21:08:09.621610+07:00 PPL404I-112 blazer_usb[7375]: Faultinfo information read in 1 tries 2023-08-19T21:08:09.623371+07:00 PPL404I-112 blazer_usb[7375]: No values provided for battery high/low voltages in ups.conf 2023-08-19T21:08:09.625487+07:00 PPL404I-112 blazer_usb[7375]: Using 'guestimation' (low: 31.200000, high: 39.000000)! 2023-08-19T21:08:09.627414+07:00 PPL404I-112 blazer_usb[7375]: Battery runtime will not be calculated (runtimecal not set) 2023-08-19T21:08:09.797715+07:00 PPL404I-112 blazer_usb[7375]: Battery information read in 1 tries 2023-08-19T21:08:11.248275+07:00 PPL404I-112 blazer_usb[7413]: Startup successful 2023-08-19T21:08:13.135375+07:00 PPL404I-112 upsd-usbd[5209]: Connected to UPS [pcmusb]: blazer_usb-pcmusb 2023-08-19T21:08:13.135584+07:00 PPL404I-112 blazer_usb[7413]: sock_connect: enabling asynchronous mode (auto) 2023-08-19T21:08:17.857033+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/ups_status 2023-08-19T21:08:21.404505+07:00 PPL404I-112 u_main.pl: Uupsd:COMMUNICATION RESTORED 2023-08-19T21:08:25.167355+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/ups_status 2023-08-19T21:08:30.480533+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/log0_trace -n 205 2023-08-19T21:08:47.174131+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/log0_trace -n 205 2023-08-19T21:08:54.772881+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/ups_status 2023-08-19T21:08:59.624130+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/log0_trace 2023-08-19T21:09:07.050581+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/log0_trace -n 205 2023-08-19T21:09:28.092217+07:00 PPL404I-112 upsd-usbd[5209]: Data for UPS [pcmusb] is stale - check driver 2023-08-19T21:09:29.270746+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2023-08-19T21:09:32.329146+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:2/3 2023-08-19T21:09:35.387564+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:3/3 2023-08-19T21:09:38.416010+07:00 PPL404I-112 u_main.pl: Uupsd:COMMUNICATION LOST-pls. check ups's connection 2023-08-19T21:09:44.668992+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2023-08-19T21:09:45.784340+07:00 PPL404I-112 blazer_usb[9945]: Please note that this driver is deprecated and will not receive#012new development. If it works for managing your devices - fine,#012but if you are running it to try setting up a new device, please#012consider the newer nutdrv_qx instead, which should handle all 'Qx'#012protocol variants for NUT. (Please also report if your device works#012with this driver, but nutdrv_qx would not actually support it with#012any subdriver!) 2023-08-19T21:09:45.999004+07:00 PPL404I-112 blazer_usb[9945]: Supported UPS detected with megatec protocol 2023-08-19T21:09:46.334578+07:00 PPL404I-112 blazer_usb[9945]: Vendor information read in 1 tries 2023-08-19T21:09:46.670655+07:00 PPL404I-112 blazer_usb[9945]: Warning information read in 1 tries 2023-08-19T21:09:46.998606+07:00 PPL404I-112 blazer_usb[9945]: Faultinfo information read in 1 tries 2023-08-19T21:09:47.000057+07:00 PPL404I-112 blazer_usb[9945]: No values provided for battery high/low voltages in ups.conf 2023-08-19T21:09:47.001677+07:00 PPL404I-112 blazer_usb[9945]: Using 'guestimation' (low: 31.200000, high: 39.000000)! 2023-08-19T21:09:47.002002+07:00 PPL404I-112 blazer_usb[9945]: Battery runtime will not be calculated (runtimecal not set) 2023-08-19T21:09:47.190677+07:00 PPL404I-112 blazer_usb[9945]: Battery information read in 1 tries 2023-08-19T21:09:48.715180+07:00 PPL404I-112 blazer_usb[10119]: Startup successful 2023-08-19T21:09:48.791636+07:00 PPL404I-112 upsd-usbd[5209]: Connected to UPS [pcmusb]: blazer_usb-pcmusb 2023-08-19T21:09:50.302657+07:00 PPL404I-112 blazer_usb[10119]: sock_connect: enabling asynchronous mode (auto) 2023-08-19T21:09:58.894199+07:00 PPL404I-112 u_main.pl: Uupsd:COMMUNICATION RESTORED 2023-08-19T21:10:13.740512+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/ups_status 2023-08-19T21:10:16.862788+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/version 2023-08-19T21:10:28.520441+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/log0_trace -n 205 2023-08-19T21:11:18.477807+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/ups_status 2023-08-19T21:13:08.658147+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/ups_cmd --help 2023-08-19T21:13:17.649528+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/ups_cmd 127.0.0.1 1622 .1.3.6.1.2.1.33.1.2.28=1 2023-08-19T21:13:30.790936+07:00 PPL404I-112 dropbear[16058]: Child connection from 192.168.99.55:58886 2023-08-19T21:13:40.232287+07:00 PPL404I-112 dropbear[16058]: Bad password attempt for 'root' from 192.168.99.55:58886 2023-08-19T21:13:45.058482+07:00 PPL404I-112 dropbear[16058]: Bad password attempt for 'root' from 192.168.99.55:58886 2023-08-19T21:13:48.820379+07:00 PPL404I-112 dropbear[16058]: Exit before auth from <192.168.99.55:58886>: (user 'root', 2 fails): Disconnect received 2023-08-19T21:14:21.828985+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2023-08-19T21:14:21.830058+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2023-08-19T21:14:22.504468+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN1 link down 2023-08-19T21:14:22.835788+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2023-08-19T21:14:22.835899+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2023-08-19T21:14:27.092117+07:00 PPL404I-112 upsd-usbd[5209]: Data for UPS [pcmusb] is stale - check driver 2023-08-19T21:14:27.110439+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2023-08-19T21:14:30.168607+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:2/3 2023-08-19T21:14:33.227400+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:3/3 2023-08-19T21:14:36.255561+07:00 PPL404I-112 u_main.pl: Uupsd:COMMUNICATION LOST-pls. check ups's connection 2023-08-19T21:14:51.868486+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T21:14:51.869772+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T21:14:51.877481+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T21:14:51.877565+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T21:14:52.339490+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2023-08-19T21:18:20.986259+07:00 PPL404I-112 dropbear[5431]: Exit (admin) from <192.168.99.55:61559>: Error reading: Connection reset by peer 2023-08-19T21:18:20.992782+07:00 PPL404I-112 CLI-admin[5431]: CLI/status/EOF 2023-08-19T21:19:43.611500+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2023-08-19T21:19:43.612550+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2023-08-19T21:19:44.647134+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2023-08-19T21:19:44.675924+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2023-08-19T21:19:44.676011+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2023-08-19T21:19:53.550042+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T21:19:53.551537+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T21:19:53.556294+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T21:19:53.556379+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T21:19:54.399860+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2023-08-19T21:19:57.021127+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2023-08-19T21:19:57.022169+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2023-08-19T21:19:57.872801+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2023-08-19T21:19:58.035771+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2023-08-19T21:19:58.035855+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2023-08-19T21:19:59.445743+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T21:19:59.447327+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T21:19:59.454405+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T21:19:59.454489+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T21:20:01.124803+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2023-08-19T21:25:27.955499+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2023-08-19T21:25:28.035851+07:00 PPL404I-112 upsd-usbd[5209]: Can't connect to UPS [pcmusb] (blazer_usb-pcmusb): Connection refused 2023-08-19T21:25:29.084800+07:00 PPL404I-112 blazer_usb[29224]: Please note that this driver is deprecated and will not receive#012new development. If it works for managing your devices - fine,#012but if you are running it to try setting up a new device, please#012consider the newer nutdrv_qx instead, which should handle all 'Qx'#012protocol variants for NUT. (Please also report if your device works#012with this driver, but nutdrv_qx would not actually support it with#012any subdriver!) 2023-08-19T21:25:29.743913+07:00 PPL404I-112 blazer_usb[29224]: Supported UPS detected with megatec protocol 2023-08-19T21:25:30.063575+07:00 PPL404I-112 blazer_usb[29224]: Vendor information read in 1 tries 2023-08-19T21:25:30.279577+07:00 PPL404I-112 blazer_usb[29224]: Warning information read in 1 tries 2023-08-19T21:25:30.599605+07:00 PPL404I-112 blazer_usb[29224]: Faultinfo information read in 1 tries 2023-08-19T21:25:30.601026+07:00 PPL404I-112 blazer_usb[29224]: No values provided for battery high/low voltages in ups.conf 2023-08-19T21:25:30.602632+07:00 PPL404I-112 blazer_usb[29224]: Using 'guestimation' (low: 31.200000, high: 39.000000)! 2023-08-19T21:25:30.604118+07:00 PPL404I-112 blazer_usb[29224]: Battery runtime will not be calculated (runtimecal not set) 2023-08-19T21:25:30.935688+07:00 PPL404I-112 blazer_usb[29224]: Battery information read in 1 tries 2023-08-19T21:25:32.402287+07:00 PPL404I-112 blazer_usb[29288]: Startup successful 2023-08-19T21:25:34.042656+07:00 PPL404I-112 upsd-usbd[5209]: Connected to UPS [pcmusb]: blazer_usb-pcmusb 2023-08-19T21:25:34.044317+07:00 PPL404I-112 blazer_usb[29288]: sock_connect: enabling asynchronous mode (auto) 2023-08-19T21:25:36.206533+07:00 PPL404I-112 dropbear[29325]: Child connection from 192.168.99.55:49683 2023-08-19T21:25:38.403024+07:00 PPL404I-112 dropbear[29325]: Password auth succeeded for 'admin' from 192.168.99.55:49683 2023-08-19T21:25:40.624404+07:00 PPL404I-112 CLI-admin[29325]: CLI 2023-08-19T21:25:42.160663+07:00 PPL404I-112 CLI-admin[29325]: CLI/config 2023-08-19T21:25:42.377245+07:00 PPL404I-112 u_main.pl: Uupsd:COMMUNICATION RESTORED 2023-08-19T21:26:14.005663+07:00 PPL404I-112 CLI-admin[29325]: CLI/status 2023-08-19T21:26:15.163897+07:00 PPL404I-112 CLI-admin[29325]: CLI/status/log0_trace -n 205 2023-08-19T21:26:21.436329+07:00 PPL404I-112 CLI-admin[29325]: CLI/status/ups_status 2023-08-19T21:26:31.493993+07:00 PPL404I-112 CLI-admin[29325]: CLI/status/ups_cmd 127.0.0.1 1621 .1.3.6.1.2.1.33.1.1.27=1 2023-08-19T21:26:32.142258+07:00 PPL404I-112 u_main.pl: Uupsd:RECEIVED-Test-Battery-10s 2023-08-19T21:26:33.322691+07:00 PPL404I-112 CLI-admin[29325]: CLI/status/log0_trace 2023-08-19T21:26:35.498872+07:00 PPL404I-112 u_main.pl: Uupsd:Current-BatteryMinuteRemaining=>Alert:224.0 2023-08-19T21:26:35.584027+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Test_Inprogress:Start=2023-08-19 21-26-35:End=:AC-Status=0:UPS-Status=OL CAL:Load=0:Battery-Charge=:Battery-Volt=40.50:Battery-Capacity=99.0:Battery-Remaining-Time=224.0 2023-08-19T21:26:46.111701+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Done:Start=2023-08-19 21-26-35:End=2023-08-19 21-26-46:AC-Status=0:UPS-Status=OL:Load=0:Battery-Charge=:Battery-Volt=41.04:Battery-Capacity=99.0:Battery-Remaining-Time=224.0 2023-08-19T21:27:19.057338+07:00 PPL404I-112 CLI-admin[29325]: CLI/status/ups_cmd 127.0.0.1 1621 .1.3.6.1.2.1.33.1.1.28=1 2023-08-19T21:27:19.625464+07:00 PPL404I-112 u_main.pl: Uupsd:RECEIVED-Test-Battery-1m 2023-08-19T21:27:22.160146+07:00 PPL404I-112 CLI-admin[29325]: CLI/status/log0_trace -n 250 2023-08-19T21:27:22.195590+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-1m=>Test_Inprogress:Start=2023-08-19 21-27-22:End=:AC-Status=0:UPS-Status=OL CAL:Load=0:Battery-Charge=:Battery-Volt=40.68:Battery-Capacity=99.0:Battery-Remaining-Time=224.0 2023-08-19T21:28:20.947795+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-1m=>Done:Start=2023-08-19 21-27-22:End=2023-08-19 21-28-20:AC-Status=0:UPS-Status=OL:Load=0:Battery-Charge=:Battery-Volt=42.30:Battery-Capacity=99.0:Battery-Remaining-Time=223.0 2023-08-19T21:31:40.749633+07:00 PPL404I-112 CLI-admin[29325]: CLI/status/log0_trace -n 205 2023-08-19T21:33:14.519695+07:00 PPL404I-112 CLI-admin[29325]: CLI/status/log0_trace -n 205 2023-08-19T21:34:23.222159+07:00 PPL404I-112 dropbear[19645]: Child connection from 192.168.99.55:49754 2023-08-19T21:35:01.798571+07:00 PPL404I-112 dropbear[19645]: Password auth succeeded for 'root' from 192.168.99.55:49754 2023-08-19T21:47:00.760961+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2023-08-19T21:47:00.762006+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2023-08-19T21:47:01.718585+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2023-08-19T21:47:01.795975+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2023-08-19T21:47:01.796061+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2023-08-19T21:52:40.026307+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T21:52:40.027597+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T21:52:40.036298+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T21:52:40.036382+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T21:52:40.472840+07:00 PPL404I-112 dropbear[19645]: Exit (root) from <192.168.99.55:49754>: Error reading: Connection reset by peer 2023-08-19T21:52:40.474199+07:00 PPL404I-112 dropbear[29325]: Exit (admin) from <192.168.99.55:49683>: Error reading: Connection reset by peer 2023-08-19T21:52:42.461429+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN1 link up 2023-08-19T22:08:00.212969+07:00 PPL404I-112 crond[2639]: USER root pid 1385 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2023-08-19T22:54:12.479153+07:00 PPL404I-112 upsd-usbd[5209]: Data for UPS [pcmusb] is stale - check driver 2023-08-19T22:54:12.497589+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2023-08-19T22:54:12.529251+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2023-08-19T22:54:12.610160+07:00 PPL404I-112 upsd-usbd[5209]: Can't connect to UPS [pcmusb] (blazer_usb-pcmusb): Connection refused 2023-08-19T22:54:13.610227+07:00 PPL404I-112 blazer_usb[954]: Please note that this driver is deprecated and will not receive#012new development. If it works for managing your devices - fine,#012but if you are running it to try setting up a new device, please#012consider the newer nutdrv_qx instead, which should handle all 'Qx'#012protocol variants for NUT. (Please also report if your device works#012with this driver, but nutdrv_qx would not actually support it with#012any subdriver!) 2023-08-19T22:54:14.064004+07:00 PPL404I-112 blazer_usb[954]: Supported UPS detected with megatec protocol 2023-08-19T22:54:14.543567+07:00 PPL404I-112 blazer_usb[954]: Vendor information read in 1 tries 2023-08-19T22:54:14.759580+07:00 PPL404I-112 blazer_usb[954]: Warning information read in 1 tries 2023-08-19T22:54:15.087608+07:00 PPL404I-112 blazer_usb[954]: Faultinfo information read in 1 tries 2023-08-19T22:54:15.089050+07:00 PPL404I-112 blazer_usb[954]: No values provided for battery high/low voltages in ups.conf 2023-08-19T22:54:15.091042+07:00 PPL404I-112 blazer_usb[954]: Using 'guestimation' (low: 31.200000, high: 39.000000)! 2023-08-19T22:54:15.092547+07:00 PPL404I-112 blazer_usb[954]: Battery runtime will not be calculated (runtimecal not set) 2023-08-19T22:54:15.279684+07:00 PPL404I-112 blazer_usb[954]: Battery information read in 1 tries 2023-08-19T22:54:16.922480+07:00 PPL404I-112 blazer_usb[1005]: Startup successful 2023-08-19T22:54:18.615299+07:00 PPL404I-112 upsd-usbd[5209]: Connected to UPS [pcmusb]: blazer_usb-pcmusb 2023-08-19T22:54:18.616936+07:00 PPL404I-112 blazer_usb[1005]: sock_connect: enabling asynchronous mode (auto) 2023-08-19T23:07:11.000000+07:00 PPL404I-112 boot[905] ********************* PWR logger-Power Up(syslog) ******************* 2023-08-19T23:07:42.623244+07:00 PPL404I-112 : [origin software="rsyslogd" swVersion="8.2110.0" x-pid="2546" x-info="https://www.rsyslog.com"] start 2023-08-19T23:07:46.879465+07:00 PPL404I-112 root: /opt/pp/CLI/sbin/pre_zl502.sh 2023-08-19T23:07:51.634506+07:00 PPL404I-112 root: service QoS Stop ... 2023-08-19T23:07:52.152207+07:00 PPL404I-112 root: [serial_upsd]...Stopped 2023-08-19T23:07:53.389016+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN4 link down 2023-08-19T23:07:53.693070+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN3 link down 2023-08-19T23:07:53.882456+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2023-08-19T23:07:54.010956+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN1 link down 2023-08-19T23:07:54.142391+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: wan link down 2023-08-19T23:07:55.667119+07:00 PPL404I-112 root: /opt/pp/CLI/sbin/post_zl502.sh 2023-08-19T23:07:59.064655+07:00 PPL404I-112 root: service iptables Stop ... 2023-08-19T23:08:00.617947+07:00 PPL404I-112 crond[2683]: USER root pid 4080 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2023-08-19T23:08:02.300632+07:00 PPL404I-112 procd: - init complete - 2023-08-19T23:08:02.966390+07:00 PPL404I-112 root: [serial_upsd]...Stopped 2023-08-19T23:08:03.303463+07:00 PPL404I-112 root: service QoS Stop ... 2023-08-19T23:08:07.753907+07:00 PPL404I-112 root: [usb_upsd]...Stopped 2023-08-19T23:08:09.312228+07:00 PPL404I-112 root: service iptables Stop ... 2023-08-19T23:08:10.880381+07:00 PPL404I-112 root: service iptables Starting ... 2023-08-19T23:08:16.282288+07:00 PPL404I-112 root: [nut-server-usb]...Stopped 2023-08-19T23:08:16.374744+07:00 PPL404I-112 netifd: Interface 'lan' is enabled 2023-08-19T23:08:16.398426+07:00 PPL404I-112 netifd: Interface 'lan' is now up 2023-08-19T23:08:16.421558+07:00 PPL404I-112 root: [usb_upsd]...Started 2023-08-19T23:08:17.536234+07:00 PPL404I-112 netifd: Interface 'loopback' is enabled 2023-08-19T23:08:17.545228+07:00 PPL404I-112 netifd: Interface 'loopback' is now up 2023-08-19T23:08:17.655464+07:00 PPL404I-112 netifd: Interface 'loopback' has link connectivity 2023-08-19T23:08:28.025357+07:00 PPL404I-112 root: [nut-server-usb]...Stopped 2023-08-19T23:08:29.407728+07:00 PPL404I-112 blazer_usb[5368]: Please note that this driver is deprecated and will not receive#012new development. If it works for managing your devices - fine,#012but if you are running it to try setting up a new device, please#012consider the newer nutdrv_qx instead, which should handle all 'Qx'#012protocol variants for NUT. (Please also report if your device works#012with this driver, but nutdrv_qx would not actually support it with#012any subdriver!) 2023-08-19T23:08:29.641919+07:00 PPL404I-112 blazer_usb[5368]: Supported UPS detected with megatec protocol 2023-08-19T23:08:30.121427+07:00 PPL404I-112 blazer_usb[5368]: Vendor information read in 1 tries 2023-08-19T23:08:30.377411+07:00 PPL404I-112 blazer_usb[5368]: Warning information read in 1 tries 2023-08-19T23:08:30.697442+07:00 PPL404I-112 blazer_usb[5368]: Faultinfo information read in 1 tries 2023-08-19T23:08:30.699200+07:00 PPL404I-112 blazer_usb[5368]: No values provided for battery high/low voltages in ups.conf 2023-08-19T23:08:30.701180+07:00 PPL404I-112 blazer_usb[5368]: Using 'guestimation' (low: 31.200000, high: 39.000000)! 2023-08-19T23:08:30.703036+07:00 PPL404I-112 blazer_usb[5368]: Battery runtime will not be calculated (runtimecal not set) 2023-08-19T23:08:30.873508+07:00 PPL404I-112 blazer_usb[5368]: Battery information read in 1 tries 2023-08-19T23:08:32.481610+07:00 PPL404I-112 root: [nut-driver-usb]...Started 2023-08-19T23:08:32.483587+07:00 PPL404I-112 blazer_usb[5424]: Startup successful 2023-08-19T23:08:32.573124+07:00 PPL404I-112 upsd-usbd[5426]: listening on 127.0.0.1 port 6490 2023-08-19T23:08:32.578247+07:00 PPL404I-112 upsd-usbd[5426]: Connected to UPS [pcmusb]: blazer_usb-pcmusb 2023-08-19T23:08:32.697938+07:00 PPL404I-112 upsd-usbd[5427]: Startup successful 2023-08-19T23:08:32.702933+07:00 PPL404I-112 root: [nut-server-usb]...Started 2023-08-19T23:08:33.953648+07:00 PPL404I-112 blazer_usb[5424]: sock_connect: enabling asynchronous mode (auto) 2023-08-19T23:08:43.597805+07:00 PPL404I-112 u_main.pl: Uupsd:Current load='0' vs Threshold='50' 2023-08-19T23:08:43.602882+07:00 PPL404I-112 u_main.pl: Uupsd:Current Battery_MinuteRemaining='225.0' vs Threshold='252' 2023-08-19T23:08:43.605498+07:00 PPL404I-112 u_main.pl: Uupsd:Current temperature='22.7' vs Threshold='50' 2023-08-19T23:08:43.743973+07:00 PPL404I-112 u_main.pl: Uupsd:Start-Service:AC-Status=0:UPS-Status=OL:Manual-Shutdown=0:Beeper=enabled 2023-08-19T23:08:43.748783+07:00 PPL404I-112 u_main.pl: Uupsd:UPS-Beeper=>Enable 2023-08-19T23:08:44.652927+07:00 PPL404I-112 hu_sys.pl: Uupsd:Syslog_Interval=300 2023-08-19T23:14:55.340208+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T23:14:55.344164+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T23:14:55.355105+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T23:14:55.357089+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T23:14:55.808385+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN1 link up 2023-08-19T23:15:06.627976+07:00 PPL404I-112 dropbear[14923]: Child connection from 192.168.99.55:57585 2023-08-19T23:15:11.116001+07:00 PPL404I-112 dropbear[14923]: Password auth succeeded for 'admin' from 192.168.99.55:57585 2023-08-19T23:15:19.481369+07:00 PPL404I-112 CLI-admin[14923]: CLI 2023-08-19T23:15:20.651202+07:00 PPL404I-112 CLI-admin[14923]: CLI/status 2023-08-19T23:15:20.670610+07:00 PPL404I-112 CLI-admin[14923]: CLI/status/running_config | grep cli 2023-08-19T23:15:32.295414+07:00 PPL404I-112 CLI-admin[14923]: CLI/status/running_config | grep ups 2023-08-19T23:16:29.923717+07:00 PPL404I-112 CLI-admin[14923]: CLI/status/log0_trace 2023-08-19T23:16:34.622871+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2023-08-19T23:16:34.624423+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2023-08-19T23:16:35.025542+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN1 link down 2023-08-19T23:16:35.647960+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2023-08-19T23:16:35.648044+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2023-08-19T23:18:18.735563+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T23:18:18.742477+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T23:18:18.767934+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T23:18:18.768022+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T23:18:19.678730+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2023-08-19T23:18:19.970822+07:00 PPL404I-112 dropbear[14923]: Exit (admin) from <192.168.99.55:57585>: Error reading: Connection reset by peer 2023-08-19T23:18:21.149335+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2023-08-19T23:18:21.150391+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2023-08-19T23:18:22.207882+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2023-08-19T23:18:22.207969+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2023-08-19T23:18:22.939361+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2023-08-19T23:18:24.503606+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T23:18:24.504906+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T23:18:24.511181+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T23:18:24.511266+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T23:18:26.193644+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2023-08-19T23:19:01.519543+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2023-08-19T23:19:01.520593+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2023-08-19T23:19:01.930690+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2023-08-19T23:19:02.527841+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2023-08-19T23:19:02.527927+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2023-08-19T23:19:04.878474+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2023-08-19T23:19:04.879799+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2023-08-19T23:19:04.888037+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2023-08-19T23:19:04.888125+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2023-08-19T23:19:05.183832+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2023-08-19T23:20:19.446171+07:00 PPL404I-112 dropbear[22216]: Child connection from 192.168.99.55:61794 2023-08-19T23:20:23.090034+07:00 PPL404I-112 dropbear[22216]: Password auth succeeded for 'admin' from 192.168.99.55:61794 2023-08-19T23:20:25.688061+07:00 PPL404I-112 CLI-admin[22216]: CLI 2023-08-19T23:20:25.761441+07:00 PPL404I-112 CLI-admin[22216]: CLI/status 2023-08-19T23:20:27.883587+07:00 PPL404I-112 CLI-admin[22216]: CLI/status/log0_trace -n 250 2023-08-19T23:24:36.554324+07:00 PPL404I-112 CLI-admin[22216]: CLI/status/ups_status 2023-08-19T23:24:45.680728+07:00 PPL404I-112 CLI-admin[22216]: CLI/status/log0_trace -n 2250 | grep driver 2023-08-19T23:24:53.580060+07:00 PPL404I-112 CLI-admin[22216]: CLI/status/log0_trace -n 2250 | grep check 2023-08-19T23:25:15.780002+07:00 PPL404I-112 CLI-admin[22216]: CLI/status/log0_trace -n 2500000 | grep stale 2023-08-19T23:25:22.076945+07:00 PPL404I-112 CLI-admin[22216]: CLI/status/log0_trace 2023-08-19T23:29:25.079895+07:00 PPL404I-112 CLI-admin[22216]: CLI/status/date -s '2025-01-24 14:10:00' 2025-01-24T14:10:23.062418+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2025-01-24T14:10:23.063468+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2025-01-24T14:10:24.091906+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2025-01-24T14:10:24.091991+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2025-01-24T14:10:25.652703+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-24T14:10:26.692384+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2025-01-24T14:10:26.693681+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2025-01-24T14:10:26.700455+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2025-01-24T14:10:26.700541+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2025-01-24T14:10:28.906529+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-24T14:10:31.909100+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2025-01-24T14:10:31.910151+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2025-01-24T14:10:32.159461+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-24T14:10:32.971967+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2025-01-24T14:10:32.972053+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2025-01-24T14:10:35.260568+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2025-01-24T14:10:35.263684+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2025-01-24T14:10:35.294359+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2025-01-24T14:10:35.294443+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2025-01-24T14:10:35.425932+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-24T14:10:35.551752+07:00 PPL404I-112 crond[2683]: time disparity of 754001 minutes detected 2025-01-24T14:10:38.778666+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2025-01-24T14:10:38.779750+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2025-01-24T14:10:39.771941+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2025-01-24T14:10:39.772025+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2025-01-24T14:10:41.942538+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-24T14:10:42.105134+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2025-01-24T14:10:42.106450+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2025-01-24T14:10:42.114072+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2025-01-24T14:10:42.114158+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2025-01-24T14:10:45.195700+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-24T14:11:19.208603+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2025-01-24T14:11:19.209654+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2025-01-24T14:11:20.251901+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2025-01-24T14:11:20.251987+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2025-01-24T14:11:21.925625+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-24T14:11:22.559250+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2025-01-24T14:11:22.560556+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2025-01-24T14:11:22.567790+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2025-01-24T14:11:22.567874+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2025-01-24T14:11:25.185026+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-24T14:12:37.302994+07:00 PPL404I-112 dropbear[5851]: Child connection from 192.168.99.55:57536 2025-01-24T14:12:39.816396+07:00 PPL404I-112 dropbear[5851]: Password auth succeeded for 'admin' from 192.168.99.55:57536 2025-01-24T14:12:42.219700+07:00 PPL404I-112 CLI-admin[5851]: CLI 2025-01-24T14:12:50.599791+07:00 PPL404I-112 CLI-admin[5851]: CLI/status 2025-01-24T14:12:52.104420+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/log0_trace -n 205 2025-01-24T14:12:59.769230+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/ups_status 2025-01-24T14:13:03.989687+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/log0_trace 2025-01-24T14:15:00.415744+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/ups_cmd 127.0.0.1 1621 .1.3.6.1.2.1.33.1.1.27=1 2025-01-24T14:15:00.582456+07:00 PPL404I-112 dropbear[22216]: Exit (admin) from <192.168.99.55:61794>: Error reading: Connection reset by peer 2025-01-24T14:15:00.588976+07:00 PPL404I-112 CLI-admin[22216]: CLI/status/EOF 2025-01-24T14:15:01.054356+07:00 PPL404I-112 u_main.pl: Uupsd:RECEIVED-Test-Battery-10s 2025-01-24T14:15:01.456796+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/log0_trace 2025-01-24T14:15:02.492998+07:00 PPL404I-112 u_main.pl: Uupsd:Current-BatteryMinuteRemaining=>Alert:225.0 2025-01-24T14:15:02.606445+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Test_Inprogress:Start=2025-01-24 14-15-02:End=:AC-Status=0:UPS-Status=OL CAL:Load=0:Battery-Charge=100:Battery-Volt=40.68:Battery-Capacity=100.0:Battery-Remaining-Time=225.0 2025-01-24T14:15:11.194960+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2025-01-24T14:15:11.196017+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2025-01-24T14:15:12.252120+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2025-01-24T14:15:12.252205+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2025-01-24T14:15:12.554544+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-24T14:15:13.114149+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2025-01-24T14:15:13.115470+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2025-01-24T14:15:13.262660+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2025-01-24T14:15:13.262746+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2025-01-24T14:15:14.249757+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Done:Start=2025-01-24 14-15-02:End=2025-01-24 14-15-14:AC-Status=0:UPS-Status=OL:Load=0:Battery-Charge=100:Battery-Volt=41.04:Battery-Capacity=99.0:Battery-Remaining-Time=225.0 2025-01-24T14:15:16.556512+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-24T14:19:01.424100+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/ups_cmd 127.0.0.1 1622 .1.3.6.1.2.1.33.1.2.31=1 2025-01-24T14:20:17.924522+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/ups_cmd 127.0.0.1 1621 .1.3.6.1.2.1.33.1.1.27=1 2025-01-24T14:20:18.448100+07:00 PPL404I-112 u_main.pl: Uupsd:RECEIVED-Test-Battery-10s 2025-01-24T14:20:19.158021+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/log0_trace 2025-01-24T14:20:21.806342+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Test_Inprogress:Start=2025-01-24 14-20-21:End=:AC-Status=0:UPS-Status=OL CAL:Load=0:Battery-Charge=100:Battery-Volt=40.68:Battery-Capacity=99.0:Battery-Remaining-Time=225.0 2025-01-24T14:20:29.114539+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2025-01-24T14:20:29.115568+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2025-01-24T14:20:30.172037+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2025-01-24T14:20:30.172123+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2025-01-24T14:20:30.802475+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-24T14:20:31.094286+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2025-01-24T14:20:31.095545+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2025-01-24T14:20:31.103154+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2025-01-24T14:20:31.103239+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2025-01-24T14:20:31.530546+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Done:Start=2025-01-24 14-20-21:End=2025-01-24 14-20-31:AC-Status=0:UPS-Status=OL:Load=0:Battery-Charge=100:Battery-Volt=42.84:Battery-Capacity=99.0:Battery-Remaining-Time=225.0 2025-01-24T14:20:34.177267+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-24T14:21:02.462675+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/log0_trace 2025-01-24T14:22:34.876187+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/ups_status 2025-01-24T14:24:15.653258+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/ups_cmd 127.0.0.1 1621 .1.3.6.1.2.1.33.1.1.27=1 2025-01-24T14:24:16.069826+07:00 PPL404I-112 u_main.pl: Uupsd:RECEIVED-Test-Battery-10s 2025-01-24T14:24:17.027191+07:00 PPL404I-112 CLI-admin[5851]: CLI/status/log0_trace 2025-01-24T14:24:19.424980+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Test_Inprogress:Start=2025-01-24 14-24-19:End=:AC-Status=0:UPS-Status=OL CAL:Load=0:Battery-Charge=100:Battery-Volt=40.68:Battery-Capacity=99.0:Battery-Remaining-Time=225.0 2025-01-24T14:24:29.125694+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Done:Start=2025-01-24 14-24-19:End=2025-01-24 14-24-29:AC-Status=0:UPS-Status=OL:Load=0:Battery-Charge=100:Battery-Volt=42.66:Battery-Capacity=99.0:Battery-Remaining-Time=225.0 2025-01-24T14:27:19.468254+07:00 PPL404I-112 dropbear[7365]: Child connection from 192.168.99.55:61016 2025-01-24T14:27:20.081939+07:00 PPL404I-112 dropbear[5851]: Exit (admin) from <192.168.99.55:57536>: Error reading: Connection reset by peer 2025-01-24T14:27:22.358904+07:00 PPL404I-112 dropbear[7365]: Password auth succeeded for 'admin' from 192.168.99.55:61016 2025-01-24T14:27:24.339007+07:00 PPL404I-112 CLI-admin[7365]: CLI 2025-01-24T14:27:27.799421+07:00 PPL404I-112 CLI-admin[7365]: CLI/status 2025-01-24T14:27:29.204222+07:00 PPL404I-112 CLI-admin[7365]: CLI/status/log0_trace -n 205 2025-01-24T14:30:15.000632+07:00 PPL404I-112 upsd-usbd[5427]: Data for UPS [pcmusb] is stale - check driver 2025-01-24T14:30:18.184424+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-24T14:30:18.222641+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-24T14:30:18.304472+07:00 PPL404I-112 upsd-usbd[5427]: Can't connect to UPS [pcmusb] (blazer_usb-pcmusb): Connection refused 2025-01-24T14:30:19.306076+07:00 PPL404I-112 blazer_usb[11258]: Please note that this driver is deprecated and will not receive#012new development. If it works for managing your devices - fine,#012but if you are running it to try setting up a new device, please#012consider the newer nutdrv_qx instead, which should handle all 'Qx'#012protocol variants for NUT. (Please also report if your device works#012with this driver, but nutdrv_qx would not actually support it with#012any subdriver!) 2025-01-24T14:30:19.925885+07:00 PPL404I-112 blazer_usb[11258]: Supported UPS detected with megatec protocol 2025-01-24T14:30:20.269552+07:00 PPL404I-112 blazer_usb[11258]: Vendor information read in 1 tries 2025-01-24T14:30:20.461473+07:00 PPL404I-112 blazer_usb[11258]: Warning information read in 1 tries 2025-01-24T14:30:20.805648+07:00 PPL404I-112 blazer_usb[11258]: Faultinfo information read in 1 tries 2025-01-24T14:30:20.805748+07:00 PPL404I-112 blazer_usb[11258]: No values provided for battery high/low voltages in ups.conf 2025-01-24T14:30:20.805905+07:00 PPL404I-112 blazer_usb[11258]: Using 'guestimation' (low: 31.200000, high: 39.000000)! 2025-01-24T14:30:20.805979+07:00 PPL404I-112 blazer_usb[11258]: Battery runtime will not be calculated (runtimecal not set) 2025-01-24T14:30:21.117576+07:00 PPL404I-112 blazer_usb[11258]: Battery information read in 1 tries 2025-01-24T14:30:22.600186+07:00 PPL404I-112 blazer_usb[11296]: Startup successful 2025-01-24T14:30:24.311289+07:00 PPL404I-112 upsd-usbd[5427]: Connected to UPS [pcmusb]: blazer_usb-pcmusb 2025-01-24T14:30:24.311516+07:00 PPL404I-112 blazer_usb[11296]: sock_connect: enabling asynchronous mode (auto) 2025-01-24T15:01:07.296067+07:00 PPL404I-112 upsd-usbd[5427]: Data for UPS [pcmusb] is stale - check driver 2025-01-24T15:01:08.475687+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-24T15:01:08.505000+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-24T15:01:08.586705+07:00 PPL404I-112 upsd-usbd[5427]: Can't connect to UPS [pcmusb] (blazer_usb-pcmusb): Connection refused 2025-01-24T15:01:09.640941+07:00 PPL404I-112 blazer_usb[21454]: Please note that this driver is deprecated and will not receive#012new development. If it works for managing your devices - fine,#012but if you are running it to try setting up a new device, please#012consider the newer nutdrv_qx instead, which should handle all 'Qx'#012protocol variants for NUT. (Please also report if your device works#012with this driver, but nutdrv_qx would not actually support it with#012any subdriver!) 2025-01-24T15:01:09.894050+07:00 PPL404I-112 blazer_usb[21454]: Supported UPS detected with megatec protocol 2025-01-24T15:01:10.221681+07:00 PPL404I-112 blazer_usb[21454]: Vendor information read in 1 tries 2025-01-24T15:01:10.613702+07:00 PPL404I-112 blazer_usb[21454]: Warning information read in 1 tries 2025-01-24T15:01:10.957860+07:00 PPL404I-112 blazer_usb[21454]: Faultinfo information read in 1 tries 2025-01-24T15:01:10.957959+07:00 PPL404I-112 blazer_usb[21454]: No values provided for battery high/low voltages in ups.conf 2025-01-24T15:01:10.958123+07:00 PPL404I-112 blazer_usb[21454]: Using 'guestimation' (low: 31.200000, high: 39.000000)! 2025-01-24T15:01:10.958198+07:00 PPL404I-112 blazer_usb[21454]: Battery runtime will not be calculated (runtimecal not set) 2025-01-24T15:01:11.133679+07:00 PPL404I-112 blazer_usb[21454]: Battery information read in 1 tries 2025-01-24T15:01:12.616298+07:00 PPL404I-112 blazer_usb[21961]: Startup successful 2025-01-24T15:01:14.593588+07:00 PPL404I-112 upsd-usbd[5427]: Connected to UPS [pcmusb]: blazer_usb-pcmusb 2025-01-24T15:01:14.595218+07:00 PPL404I-112 blazer_usb[21961]: sock_connect: enabling asynchronous mode (auto) 2025-01-24T15:04:30.467286+07:00 PPL404I-112 CLI-admin[7365]: CLI/status/log0_trace 2025-01-24T15:04:53.830371+07:00 PPL404I-112 CLI-admin[7365]: CLI/status/log0_trace -n 25000000 | grep stale | grep check 2025-01-24T15:04:59.904764+07:00 PPL404I-112 CLI-admin[7365]: CLI/status/log0_trace -n 25000000 | grep stale 2025-01-24T15:05:07.754590+07:00 PPL404I-112 CLI-admin[7365]: CLI/status/log0_trace -n 205 2025-01-24T15:08:00.598561+07:00 PPL404I-112 crond[2683]: USER root pid 31107 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-24T15:23:39.541509+07:00 PPL404I-112 dropbear[7365]: Exit (admin) from <192.168.99.55:61016>: Keepalive timeout 2025-01-24T15:31:07.351172+07:00 PPL404I-112 dropbear[30426]: Child connection from 192.168.99.55:64486 2025-01-24T15:31:10.120047+07:00 PPL404I-112 dropbear[30426]: Password auth succeeded for 'admin' from 192.168.99.55:64486 2025-01-24T15:31:12.415250+07:00 PPL404I-112 CLI-admin[30426]: CLI 2025-01-24T15:31:12.501331+07:00 PPL404I-112 CLI-admin[30426]: CLI/status 2025-01-24T15:31:14.582880+07:00 PPL404I-112 CLI-admin[30426]: CLI/status/log0_trace -n 2500 2025-01-24T15:38:34.924819+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2025-01-24T15:38:34.925831+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2025-01-24T15:38:35.931891+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2025-01-24T15:38:35.931978+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2025-01-24T15:38:37.604198+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-24T15:38:38.278417+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2025-01-24T15:38:38.279257+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2025-01-24T15:38:38.286308+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2025-01-24T15:38:38.286390+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2025-01-24T15:38:39.941397+07:00 PPL404I-112 dropbear[30426]: Exit (admin) from <192.168.99.55:64486>: Error reading: Connection reset by peer 2025-01-24T15:38:40.968390+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-24T15:38:57.321025+07:00 PPL404I-112 dropbear[9062]: Child connection from 192.168.99.55:64148 2025-01-24T15:38:59.860847+07:00 PPL404I-112 dropbear[9062]: Password auth succeeded for 'admin' from 192.168.99.55:64148 2025-01-24T15:39:02.483823+07:00 PPL404I-112 CLI-admin[9062]: CLI 2025-01-24T15:39:02.558417+07:00 PPL404I-112 CLI-admin[9062]: CLI/status 2025-01-24T15:39:02.573926+07:00 PPL404I-112 CLI-admin[9062]: CLI/status/log0_trace -n 205 2025-01-24T15:44:44.993185+07:00 PPL404I-112 dropbear[16935]: Child connection from 192.168.99.55:65021 2025-01-24T15:44:46.446129+07:00 PPL404I-112 dropbear[16935]: Password auth succeeded for 'root' from 192.168.99.55:65021 2025-01-24T16:05:48.642813+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is down 2025-01-24T16:05:48.643454+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is down 2025-01-24T16:05:49.316328+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-24T16:05:49.691809+07:00 PPL404I-112 netifd: bridge 'br-lan' link is down 2025-01-24T16:05:49.691891+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity loss 2025-01-24T16:05:50.647867+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2025-01-24T16:05:50.648737+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2025-01-24T16:05:50.655749+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2025-01-24T16:05:50.655831+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2025-01-24T16:05:52.569708+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-24T16:08:00.648079+07:00 PPL404I-112 crond[2683]: USER root pid 16926 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-24T16:14:13.488978+07:00 PPL404I-112 upsd-usbd[5427]: Data for UPS [pcmusb] is stale - check driver 2025-01-24T16:14:14.670026+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-24T16:14:14.699493+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-24T16:14:14.781976+07:00 PPL404I-112 upsd-usbd[5427]: Can't connect to UPS [pcmusb] (blazer_usb-pcmusb): Connection refused 2025-01-24T16:14:15.785517+07:00 PPL404I-112 blazer_usb[25528]: Please note that this driver is deprecated and will not receive#012new development. If it works for managing your devices - fine,#012but if you are running it to try setting up a new device, please#012consider the newer nutdrv_qx instead, which should handle all 'Qx'#012protocol variants for NUT. (Please also report if your device works#012with this driver, but nutdrv_qx would not actually support it with#012any subdriver!) 2025-01-24T16:14:15.997890+07:00 PPL404I-112 blazer_usb[25528]: Supported UPS detected with megatec protocol 2025-01-24T16:14:16.341499+07:00 PPL404I-112 blazer_usb[25528]: Vendor information read in 1 tries 2025-01-24T16:14:16.693473+07:00 PPL404I-112 blazer_usb[25528]: Warning information read in 1 tries 2025-01-24T16:14:17.037702+07:00 PPL404I-112 blazer_usb[25528]: Faultinfo information read in 1 tries 2025-01-24T16:14:17.037800+07:00 PPL404I-112 blazer_usb[25528]: No values provided for battery high/low voltages in ups.conf 2025-01-24T16:14:17.037957+07:00 PPL404I-112 blazer_usb[25528]: Using 'guestimation' (low: 31.200000, high: 39.000000)! 2025-01-24T16:14:17.038033+07:00 PPL404I-112 blazer_usb[25528]: Battery runtime will not be calculated (runtimecal not set) 2025-01-24T16:14:17.213581+07:00 PPL404I-112 blazer_usb[25528]: Battery information read in 1 tries 2025-01-24T16:14:18.776386+07:00 PPL404I-112 blazer_usb[25579]: Startup successful 2025-01-24T16:14:18.786024+07:00 PPL404I-112 upsd-usbd[5427]: Connected to UPS [pcmusb]: blazer_usb-pcmusb 2025-01-24T16:14:20.405533+07:00 PPL404I-112 blazer_usb[25579]: sock_connect: enabling asynchronous mode (auto) 2025-01-24T16:44:28.538618+07:00 PPL404I-112 CLI-admin[9062]: CLI/status/log0_trace -n 2500 | grep check 2025-01-24T16:55:42.094001+07:00 PPL404I-112 dropbear[17756]: Child connection from 192.168.99.55:52702 2025-01-24T16:55:42.642396+07:00 PPL404I-112 dropbear[17756]: Password auth succeeded for 'root' from 192.168.99.55:52702 2025-01-24T16:56:17.480966+07:00 PPL404I-112 dropbear[4402]: Exit (root) from <192.168.99.55:49224>: Error reading: Connection reset by peer 2025-01-24T16:56:22.858238+07:00 PPL404I-112 dropbear[18705]: Child connection from 192.168.99.55:52728 2025-01-24T16:56:25.368052+07:00 PPL404I-112 dropbear[18705]: Password auth succeeded for 'admin' from 192.168.99.55:52728 2025-01-24T16:56:27.972648+07:00 PPL404I-112 CLI-admin[18705]: CLI 2025-01-24T16:56:30.226945+07:00 PPL404I-112 dropbear[18866]: Child connection from 192.168.99.55:52730 2025-01-24T16:56:32.977096+07:00 PPL404I-112 dropbear[18866]: Password auth succeeded for 'root' from 192.168.99.55:52730 2025-01-24T17:00:16.618293+07:00 PPL404I-112 upsd-usbd[5427]: Data for UPS [pcmusb] is stale - check driver 2025-01-24T17:00:17.887306+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-24T17:00:17.909707+07:00 PPL404I-112 dropbear[17255]: Exit (root) from <192.168.99.55:52686>: Error reading: Connection reset by peer 2025-01-24T17:00:17.951576+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-24T17:00:18.058066+07:00 PPL404I-112 upsd-usbd[5427]: Can't connect to UPS [pcmusb] (blazer_usb-pcmusb): Connection refused 2025-01-24T17:00:19.056079+07:00 PPL404I-112 blazer_usb[24325]: Please note that this driver is deprecated and will not receive#012new development. If it works for managing your devices - fine,#012but if you are running it to try setting up a new device, please#012consider the newer nutdrv_qx instead, which should handle all 'Qx'#012protocol variants for NUT. (Please also report if your device works#012with this driver, but nutdrv_qx would not actually support it with#012any subdriver!) 2025-01-24T17:00:19.493815+07:00 PPL404I-112 blazer_usb[24325]: Supported UPS detected with megatec protocol 2025-01-24T17:00:19.965476+07:00 PPL404I-112 blazer_usb[24325]: Vendor information read in 1 tries 2025-01-24T17:00:20.173477+07:00 PPL404I-112 blazer_usb[24325]: Warning information read in 1 tries 2025-01-24T17:00:20.519541+07:00 PPL404I-112 blazer_usb[24325]: Faultinfo information read in 1 tries 2025-01-24T17:00:20.519638+07:00 PPL404I-112 blazer_usb[24325]: No values provided for battery high/low voltages in ups.conf 2025-01-24T17:00:20.519797+07:00 PPL404I-112 blazer_usb[24325]: Using 'guestimation' (low: 31.200000, high: 39.000000)! 2025-01-24T17:00:20.519876+07:00 PPL404I-112 blazer_usb[24325]: Battery runtime will not be calculated (runtimecal not set) 2025-01-24T17:00:20.829567+07:00 PPL404I-112 blazer_usb[24325]: Battery information read in 1 tries 2025-01-24T17:00:22.296338+07:00 PPL404I-112 blazer_usb[24376]: Startup successful 2025-01-24T17:00:24.063642+07:00 PPL404I-112 upsd-usbd[5427]: Connected to UPS [pcmusb]: blazer_usb-pcmusb 2025-01-24T17:00:24.065283+07:00 PPL404I-112 blazer_usb[24376]: sock_connect: enabling asynchronous mode (auto) 2025-01-24T17:08:00.699430+07:00 PPL404I-112 crond[2683]: USER root pid 2544 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-24T17:10:35.862769+07:00 PPL404I-112 CLI-admin[18705]: CLI/status 2025-01-24T17:10:37.382695+07:00 PPL404I-112 CLI-admin[18705]: CLI/status/log0_trace -n 205 2025-01-24T17:17:27.323280+07:00 PPL404I-112 CLI-admin[18705]: CLI/status/log0_trace -n 205 2025-01-24T17:18:25.177001+07:00 PPL404I-112 dropbear[17756]: Exit (root) from <192.168.99.55:52702>: Exited normally 2025-01-24T17:18:31.355819+07:00 PPL404I-112 dropbear[17291]: Child connection from 192.168.99.55:63690 2025-01-24T17:18:31.715204+07:00 PPL404I-112 dropbear[17291]: Password auth succeeded for 'root' from 192.168.99.55:63690 -------------- next part -------------- 2025-01-29T16:56:32.000000+07:00 PPL404I-112 boot[904] ********************* PWR logger-Power Up(syslog) ******************* 2025-01-29T16:57:01.629623+07:00 PPL404I-112 : [origin software="rsyslogd" swVersion="8.2110.0" x-pid="2343" x-info="https://www.rsyslog.com"] start 2025-01-29T16:57:05.917969+07:00 PPL404I-112 root: /opt/pp/CLI/sbin/pre_zl502.sh 2025-01-29T16:57:10.177990+07:00 PPL404I-112 root: service QoS Stop ... 2025-01-29T16:57:10.569591+07:00 PPL404I-112 root: [serial_upsd]...Stopped 2025-01-29T16:57:11.435186+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN4 link up 2025-01-29T16:57:11.705109+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN3 link down 2025-01-29T16:57:11.837841+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-29T16:57:11.968921+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN1 link down 2025-01-29T16:57:12.088005+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: wan link up 2025-01-29T16:57:14.287972+07:00 PPL404I-112 root: /opt/pp/CLI/sbin/post_zl502.sh 2025-01-29T16:57:14.786295+07:00 PPL404I-112 netifd: Interface 'lan' is enabled 2025-01-29T16:57:14.806437+07:00 PPL404I-112 netifd: Interface 'lan' is now up 2025-01-29T16:57:14.812078+07:00 PPL404I-112 netifd: bridge 'br-lan' link is up 2025-01-29T16:57:14.832910+07:00 PPL404I-112 netifd: Interface 'lan' has link connectivity 2025-01-29T16:57:15.518085+07:00 PPL404I-112 root: service iptables Stop ... 2025-01-29T16:57:21.384669+07:00 PPL404I-112 procd: - init complete - 2025-01-29T16:57:22.599863+07:00 PPL404I-112 root: service QoS Stop ... 2025-01-29T16:57:23.030891+07:00 PPL404I-112 root: [serial_upsd]...Stopped 2025-01-29T16:57:27.767963+07:00 PPL404I-112 root: [usb_upsd]...Stopped 2025-01-29T16:57:28.028640+07:00 PPL404I-112 root: service iptables Stop ... 2025-01-29T16:57:29.608181+07:00 PPL404I-112 root: service iptables Starting ... 2025-01-29T16:57:38.498806+07:00 PPL404I-112 netifd: VLAN 'eth0.1' link is up 2025-01-29T16:57:38.619843+07:00 PPL404I-112 netifd: Interface 'loopback' is enabled 2025-01-29T16:57:38.705448+07:00 PPL404I-112 netifd: Interface 'loopback' is now up 2025-01-29T16:57:38.730212+07:00 PPL404I-112 netifd: Interface 'wan' is enabled 2025-01-29T16:57:38.744839+07:00 PPL404I-112 netifd: Interface 'wan' is now up 2025-01-29T16:57:39.115236+07:00 PPL404I-112 netifd: Interface 'loopback' has link connectivity 2025-01-29T16:57:39.119386+07:00 PPL404I-112 netifd: VLAN 'eth0.2' link is up 2025-01-29T16:57:39.183022+07:00 PPL404I-112 netifd: Interface 'wan' has link connectivity 2025-01-29T16:57:39.221158+07:00 PPL404I-112 root: [nut-server-usb]...Stopped 2025-01-29T16:57:39.358038+07:00 PPL404I-112 root: [usb_upsd]...Started 2025-01-29T16:57:45.827626+07:00 PPL404I-112 dropbear[4943]: Child connection from 172.31.1.55:49918 2025-01-29T16:57:50.826266+07:00 PPL404I-112 dnsmasq[5076]: started, version 2.89 cachesize 150 2025-01-29T16:57:50.832993+07:00 PPL404I-112 dnsmasq[5076]: DNS service limited to local subnets 2025-01-29T16:57:50.838236+07:00 PPL404I-112 dnsmasq[5076]: UBus support enabled: connected to system bus 2025-01-29T16:57:50.840174+07:00 PPL404I-112 dnsmasq-dhcp[5076]: DHCP, IP range 192.168.99.200 -- 192.168.99.249, lease time 12h 2025-01-29T16:57:50.842287+07:00 PPL404I-112 dnsmasq[5076]: using nameserver 1.1.1.1#53 2025-01-29T16:57:50.846608+07:00 PPL404I-112 dnsmasq[5076]: using nameserver 8.8.8.8#53 2025-01-29T16:57:50.871622+07:00 PPL404I-112 dnsmasq[5076]: read /etc/hosts - 12 names 2025-01-29T16:57:50.873657+07:00 PPL404I-112 dnsmasq[5076]: read /tmp/hosts/dhcp.cfg01411c - 2 names 2025-01-29T16:57:51.309040+07:00 PPL404I-112 dnsmasq-dhcp[5076]: read /etc/ethers - 0 addresses 2025-01-29T16:57:54.178483+07:00 PPL404I-112 hostapd: ACS: Automatic channel selection started, this may take a bit 2025-01-29T16:57:54.197505+07:00 PPL404I-112 hostapd: wlan0: interface state UNINITIALIZED->ACS 2025-01-29T16:57:54.200482+07:00 PPL404I-112 hostapd: wlan0: ACS-STARTED 2025-01-29T16:57:55.790047+07:00 PPL404I-112 netifd: Wireless device 'radio0' is now up 2025-01-29T16:57:56.224521+07:00 PPL404I-112 hostapd: wlan0: ACS-COMPLETED freq=2437 channel=6 2025-01-29T16:57:59.055982+07:00 PPL404I-112 dropbear[4943]: Password auth succeeded for 'admin' from 172.31.1.55:49918 2025-01-29T16:57:59.987649+07:00 PPL404I-112 hostapd: wlan0: interface state ACS->ENABLED 2025-01-29T16:57:59.989133+07:00 PPL404I-112 hostapd: wlan0: AP-ENABLED 2025-01-29T16:58:01.485111+07:00 PPL404I-112 dropbear[5400]: Child connection from 192.168.99.55:50572 2025-01-29T16:58:03.085291+07:00 PPL404I-112 root: [nut-server-usb]...Stopped 2025-01-29T16:58:06.683281+07:00 PPL404I-112 nutdrv_qx[5434]: device.serial: UPS reported a non-significant serial [0000000000000000] 2025-01-29T16:58:39.990101+07:00 PPL404I-112 ntpdate[5052]: step time server 202.28.116.236 offset +32.624395 sec 2025-01-29T16:58:40.555852+07:00 PPL404I-112 nutdrv_qx[5434]: battery_number: 3 2025-01-29T16:58:40.555958+07:00 PPL404I-112 nutdrv_qx[5434]: battery_number, settable range: 1..9 2025-01-29T16:58:40.886013+07:00 PPL404I-112 dropbear[5400]: Password auth succeeded for 'admin' from 192.168.99.55:50572 2025-01-29T16:58:41.308906+07:00 PPL404I-112 nutdrv_qx[5434]: bypass_alarm: enabled 2025-01-29T16:58:41.310345+07:00 PPL404I-112 nutdrv_qx[5434]: battery_alarm: enabled 2025-01-29T16:58:41.311708+07:00 PPL404I-112 nutdrv_qx[5434]: bypass_when_off: enabled 2025-01-29T16:58:41.313463+07:00 PPL404I-112 nutdrv_qx[5434]: alarm_control: enabled 2025-01-29T16:58:41.313869+07:00 PPL404I-112 nutdrv_qx[5434]: converter_mode: disabled 2025-01-29T16:58:41.316781+07:00 PPL404I-112 nutdrv_qx[5434]: eco_mode: enabled 2025-01-29T16:58:41.319161+07:00 PPL404I-112 nutdrv_qx[5434]: bypass_forbidding: disabled 2025-01-29T16:58:41.319661+07:00 PPL404I-112 nutdrv_qx[5434]: site_fault_detection: disabled 2025-01-29T16:58:41.875732+07:00 PPL404I-112 nutdrv_qx[5434]: max_bypass_volt: 264 2025-01-29T16:58:41.875916+07:00 PPL404I-112 nutdrv_qx[5434]: max_bypass_volt, settable range: 230..264 2025-01-29T16:58:41.876059+07:00 PPL404I-112 nutdrv_qx[5434]: min_bypass_volt: 170 2025-01-29T16:58:41.876236+07:00 PPL404I-112 nutdrv_qx[5434]: min_bypass_volt, settable range: 170..220 2025-01-29T16:58:42.019747+07:00 PPL404I-112 nutdrv_qx[5434]: max_bypass_freq: 53.0 2025-01-29T16:58:42.019892+07:00 PPL404I-112 nutdrv_qx[5434]: max_bypass_freq, settable range: 51.0..60.0 2025-01-29T16:58:42.020065+07:00 PPL404I-112 nutdrv_qx[5434]: min_bypass_freq: 47.0 2025-01-29T16:58:42.020183+07:00 PPL404I-112 nutdrv_qx[5434]: min_bypass_freq, settable range: 40.0..49.0 2025-01-29T16:58:42.772368+07:00 PPL404I-112 root: [nut-driver-usb]...Started 2025-01-29T16:58:42.774061+07:00 PPL404I-112 nutdrv_qx[5561]: Startup successful 2025-01-29T16:58:42.927967+07:00 PPL404I-112 upsd-usbd[5563]: listening on 127.0.0.1 port 6490 2025-01-29T16:58:42.934666+07:00 PPL404I-112 upsd-usbd[5563]: Connected to UPS [pcmusb]: nutdrv_qx-pcmusb 2025-01-29T16:58:43.227964+07:00 PPL404I-112 nutdrv_qx[5561]: sock_connect: enabling asynchronous mode (auto) 2025-01-29T16:58:43.274554+07:00 PPL404I-112 root: [nut-server-usb]...Started 2025-01-29T16:58:43.276208+07:00 PPL404I-112 upsd-usbd[5564]: Startup successful 2025-01-29T16:58:45.296251+07:00 PPL404I-112 CLI-admin[4943]: CLI 2025-01-29T16:58:46.495327+07:00 PPL404I-112 CLI-admin[5400]: CLI 2025-01-29T16:58:54.471281+07:00 PPL404I-112 u_main.pl: Uupsd:Current load='0' vs Threshold='50' 2025-01-29T16:58:54.476052+07:00 PPL404I-112 u_main.pl: Uupsd:Current Battery_MinuteRemaining='2' vs Threshold='252' 2025-01-29T16:58:54.486509+07:00 PPL404I-112 u_main.pl: Uupsd:Current temperature='22.2' vs Threshold='50' 2025-01-29T16:58:54.632381+07:00 PPL404I-112 u_main.pl: Uupsd:Start-Service:AC-Status=0:UPS-Status=OL:Manual-Shutdown=0:Beeper=enabled 2025-01-29T16:58:54.647789+07:00 PPL404I-112 u_main.pl: Uupsd:UPS-Beeper=>Enable 2025-01-29T16:58:55.539950+07:00 PPL404I-112 hu_sys.pl: Uupsd:Syslog_Interval=300 2025-01-29T17:02:22.922171+07:00 PPL404I-112 CLI-admin[7813]: CLI/status/ups_cmd 127.0.0.1 1621 .1.3.6.1.2.1.33.1.1.27=1 2025-01-29T17:02:23.233300+07:00 PPL404I-112 u_main.pl: Uupsd:RECEIVED-Test-Battery-10s 2025-01-29T17:02:23.419863+07:00 PPL404I-112 nutdrv_qx[5561]: instcmd(test.battery.start.quick, [NULL]) 2025-01-29T17:02:23.491675+07:00 PPL404I-112 nutdrv_qx[5561]: instcmd: SUCCEED 2025-01-29T17:02:26.163747+07:00 PPL404I-112 nutdrv_qx[5561]: battery_number: 3 2025-01-29T17:02:26.924224+07:00 PPL404I-112 nutdrv_qx[5561]: bypass_alarm: enabled 2025-01-29T17:02:26.924356+07:00 PPL404I-112 nutdrv_qx[5561]: battery_alarm: enabled 2025-01-29T17:02:26.924465+07:00 PPL404I-112 nutdrv_qx[5561]: bypass_when_off: enabled 2025-01-29T17:02:26.924748+07:00 PPL404I-112 nutdrv_qx[5561]: alarm_control: enabled 2025-01-29T17:02:26.924863+07:00 PPL404I-112 nutdrv_qx[5561]: converter_mode: disabled 2025-01-29T17:02:26.925295+07:00 PPL404I-112 nutdrv_qx[5561]: eco_mode: enabled 2025-01-29T17:02:26.925455+07:00 PPL404I-112 nutdrv_qx[5561]: bypass_forbidding: disabled 2025-01-29T17:02:26.925574+07:00 PPL404I-112 nutdrv_qx[5561]: site_fault_detection: disabled 2025-01-29T17:02:27.515590+07:00 PPL404I-112 nutdrv_qx[5561]: max_bypass_volt: 264 2025-01-29T17:02:27.517010+07:00 PPL404I-112 nutdrv_qx[5561]: min_bypass_volt: 170 2025-01-29T17:02:27.651641+07:00 PPL404I-112 nutdrv_qx[5561]: max_bypass_freq: 53.0 2025-01-29T17:02:27.653076+07:00 PPL404I-112 nutdrv_qx[5561]: min_bypass_freq: 47.0 2025-01-29T17:02:29.667908+07:00 PPL404I-112 u_main.pl: Uupsd:Current-BatteryMinuteRemaining=>Alert:2 2025-01-29T17:02:29.759342+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Test_Inprogress:Start=2025-01-29 17-02-29:End=:AC-Status=0:UPS-Status=OL CAL:Load=0:Battery-Charge=100:Battery-Volt=40.60:Battery-Capacity=99:Battery-Remaining-Time=2 2025-01-29T17:02:36.636909+07:00 PPL404I-112 u_main.pl: Uupsd:Test-Battery-10s=>Done:Start=2025-01-29 17-02-29:End=2025-01-29 17-02-36:AC-Status=0:UPS-Status=OL:Load=0:Battery-Charge=100:Battery-Volt=40.60:Battery-Capacity=99:Battery-Remaining-Time=2 2025-01-29T17:04:51.487783+07:00 PPL404I-112 CLI-admin[5400]: CLI/status/running_config | grep ups 2025-01-29T17:05:16.600257+07:00 PPL404I-112 CLI-admin[5400]: CLI/status/log0_trace -n 205 2025-01-29T17:05:48.131897+07:00 PPL404I-112 dropbear[24070]: Child connection from 192.168.99.55:64729 2025-01-29T17:05:50.926744+07:00 PPL404I-112 dropbear[24070]: Password auth succeeded for 'root' from 192.168.99.55:64729 2025-01-29T17:07:30.054760+07:00 PPL404I-112 CLI-admin[5400]: CLI/status/log0_trace -n 250 2025-01-29T17:08:00.718143+07:00 PPL404I-112 crond[2480]: USER root pid 26740 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-29T18:08:00.770033+07:00 PPL404I-112 crond[2480]: USER root pid 7558 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-29T19:08:00.819400+07:00 PPL404I-112 crond[2480]: USER root pid 20554 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-29T20:08:00.868970+07:00 PPL404I-112 crond[2480]: USER root pid 880 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-29T21:08:00.919810+07:00 PPL404I-112 crond[2480]: USER root pid 12389 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-29T22:08:00.969307+07:00 PPL404I-112 crond[2480]: USER root pid 23754 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-29T23:08:00.015795+07:00 PPL404I-112 crond[2480]: USER root pid 2184 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T00:08:00.061887+07:00 PPL404I-112 crond[2480]: USER root pid 12687 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T00:08:16.038500+07:00 PPL404I-112 ntpdate[12742]: step time server 202.28.116.236 offset +0.145794 sec 2025-01-30T01:08:00.253699+07:00 PPL404I-112 crond[2480]: USER root pid 23383 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T01:19:10.921187+07:00 PPL404I-112 upsd-usbd[5564]: Data for UPS [pcmusb] is stale - check driver 2025-01-30T01:19:12.378439+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-30T01:19:12.481222+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-30T01:19:12.634689+07:00 PPL404I-112 upsd-usbd[5564]: Can't connect to UPS [pcmusb] (nutdrv_qx-pcmusb): Connection refused 2025-01-30T01:19:15.405366+07:00 PPL404I-112 nutdrv_qx[5649]: device.serial: UPS reported a non-significant serial [0000000000000000] 2025-01-30T01:19:16.597616+07:00 PPL404I-112 nutdrv_qx[5649]: battery_number: 3 2025-01-30T01:19:16.599142+07:00 PPL404I-112 nutdrv_qx[5649]: battery_number, settable range: 1..9 2025-01-30T01:19:17.230718+07:00 PPL404I-112 nutdrv_qx[5649]: bypass_alarm: enabled 2025-01-30T01:19:17.232143+07:00 PPL404I-112 nutdrv_qx[5649]: battery_alarm: enabled 2025-01-30T01:19:17.233595+07:00 PPL404I-112 nutdrv_qx[5649]: bypass_when_off: enabled 2025-01-30T01:19:17.235349+07:00 PPL404I-112 nutdrv_qx[5649]: alarm_control: enabled 2025-01-30T01:19:17.236752+07:00 PPL404I-112 nutdrv_qx[5649]: converter_mode: disabled 2025-01-30T01:19:17.238724+07:00 PPL404I-112 nutdrv_qx[5649]: eco_mode: enabled 2025-01-30T01:19:17.240222+07:00 PPL404I-112 nutdrv_qx[5649]: bypass_forbidding: disabled 2025-01-30T01:19:17.240608+07:00 PPL404I-112 nutdrv_qx[5649]: site_fault_detection: disabled 2025-01-30T01:19:17.821395+07:00 PPL404I-112 nutdrv_qx[5649]: max_bypass_volt: 264 2025-01-30T01:19:17.822850+07:00 PPL404I-112 nutdrv_qx[5649]: max_bypass_volt, settable range: 230..264 2025-01-30T01:19:17.824401+07:00 PPL404I-112 nutdrv_qx[5649]: min_bypass_volt: 170 2025-01-30T01:19:17.825808+07:00 PPL404I-112 nutdrv_qx[5649]: min_bypass_volt, settable range: 170..220 2025-01-30T01:19:17.957421+07:00 PPL404I-112 nutdrv_qx[5649]: max_bypass_freq: 53.0 2025-01-30T01:19:17.957952+07:00 PPL404I-112 nutdrv_qx[5649]: max_bypass_freq, settable range: 51.0..60.0 2025-01-30T01:19:17.960475+07:00 PPL404I-112 nutdrv_qx[5649]: min_bypass_freq: 47.0 2025-01-30T01:19:17.960869+07:00 PPL404I-112 nutdrv_qx[5649]: min_bypass_freq, settable range: 40.0..49.0 2025-01-30T01:19:18.848576+07:00 PPL404I-112 nutdrv_qx[5687]: Startup successful 2025-01-30T01:19:20.643220+07:00 PPL404I-112 upsd-usbd[5564]: Connected to UPS [pcmusb]: nutdrv_qx-pcmusb 2025-01-30T01:19:20.643474+07:00 PPL404I-112 nutdrv_qx[5687]: sock_connect: enabling asynchronous mode (auto) 2025-01-30T01:30:13.583793+07:00 PPL404I-112 upsd-usbd[5564]: Data for UPS [pcmusb] is stale - check driver 2025-01-30T01:30:13.602950+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-30T01:30:13.633245+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-30T01:30:13.717263+07:00 PPL404I-112 upsd-usbd[5564]: Can't connect to UPS [pcmusb] (nutdrv_qx-pcmusb): Connection refused 2025-01-30T01:30:16.533400+07:00 PPL404I-112 nutdrv_qx[19405]: device.serial: UPS reported a non-significant serial [0000000000000000] 2025-01-30T01:30:17.150642+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN4 link up 2025-01-30T01:30:17.813613+07:00 PPL404I-112 nutdrv_qx[19405]: battery_number: 3 2025-01-30T01:30:17.814981+07:00 PPL404I-112 nutdrv_qx[19405]: battery_number, settable range: 1..9 2025-01-30T01:30:18.430711+07:00 PPL404I-112 nutdrv_qx[19405]: bypass_alarm: enabled 2025-01-30T01:30:18.432148+07:00 PPL404I-112 nutdrv_qx[19405]: battery_alarm: enabled 2025-01-30T01:30:18.433713+07:00 PPL404I-112 nutdrv_qx[19405]: bypass_when_off: enabled 2025-01-30T01:30:18.435483+07:00 PPL404I-112 nutdrv_qx[19405]: alarm_control: enabled 2025-01-30T01:30:18.437022+07:00 PPL404I-112 nutdrv_qx[19405]: converter_mode: disabled 2025-01-30T01:30:18.438942+07:00 PPL404I-112 nutdrv_qx[19405]: eco_mode: enabled 2025-01-30T01:30:18.439442+07:00 PPL404I-112 nutdrv_qx[19405]: bypass_forbidding: disabled 2025-01-30T01:30:18.441856+07:00 PPL404I-112 nutdrv_qx[19405]: site_fault_detection: disabled 2025-01-30T01:30:19.005439+07:00 PPL404I-112 nutdrv_qx[19405]: max_bypass_volt: 264 2025-01-30T01:30:19.006899+07:00 PPL404I-112 nutdrv_qx[19405]: max_bypass_volt, settable range: 230..264 2025-01-30T01:30:19.008357+07:00 PPL404I-112 nutdrv_qx[19405]: min_bypass_volt: 170 2025-01-30T01:30:19.009776+07:00 PPL404I-112 nutdrv_qx[19405]: min_bypass_volt, settable range: 170..220 2025-01-30T01:30:19.141486+07:00 PPL404I-112 nutdrv_qx[19405]: max_bypass_freq: 53.0 2025-01-30T01:30:19.141629+07:00 PPL404I-112 nutdrv_qx[19405]: max_bypass_freq, settable range: 51.0..60.0 2025-01-30T01:30:19.141803+07:00 PPL404I-112 nutdrv_qx[19405]: min_bypass_freq: 47.0 2025-01-30T01:30:19.141920+07:00 PPL404I-112 nutdrv_qx[19405]: min_bypass_freq, settable range: 40.0..49.0 2025-01-30T01:30:19.952580+07:00 PPL404I-112 nutdrv_qx[19446]: Startup successful 2025-01-30T01:30:21.725439+07:00 PPL404I-112 upsd-usbd[5564]: Connected to UPS [pcmusb]: nutdrv_qx-pcmusb 2025-01-30T01:30:21.725692+07:00 PPL404I-112 nutdrv_qx[19446]: sock_connect: enabling asynchronous mode (auto) 2025-01-30T01:54:18.753041+07:00 PPL404I-112 upsd-usbd[5564]: Data for UPS [pcmusb] is stale - check driver 2025-01-30T01:54:20.190499+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-30T01:54:20.252101+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-30T01:54:20.388372+07:00 PPL404I-112 upsd-usbd[5564]: Can't connect to UPS [pcmusb] (nutdrv_qx-pcmusb): Connection refused 2025-01-30T01:54:23.333384+07:00 PPL404I-112 nutdrv_qx[17716]: device.serial: UPS reported a non-significant serial [0000000000000000] 2025-01-30T01:54:24.509598+07:00 PPL404I-112 nutdrv_qx[17716]: battery_number: 3 2025-01-30T01:54:24.510943+07:00 PPL404I-112 nutdrv_qx[17716]: battery_number, settable range: 1..9 2025-01-30T01:54:25.278698+07:00 PPL404I-112 nutdrv_qx[17716]: bypass_alarm: enabled 2025-01-30T01:54:25.280109+07:00 PPL404I-112 nutdrv_qx[17716]: battery_alarm: enabled 2025-01-30T01:54:25.281461+07:00 PPL404I-112 nutdrv_qx[17716]: bypass_when_off: enabled 2025-01-30T01:54:25.283254+07:00 PPL404I-112 nutdrv_qx[17716]: alarm_control: enabled 2025-01-30T01:54:25.284652+07:00 PPL404I-112 nutdrv_qx[17716]: converter_mode: disabled 2025-01-30T01:54:25.286940+07:00 PPL404I-112 nutdrv_qx[17716]: eco_mode: enabled 2025-01-30T01:54:25.288525+07:00 PPL404I-112 nutdrv_qx[17716]: bypass_forbidding: disabled 2025-01-30T01:54:25.288897+07:00 PPL404I-112 nutdrv_qx[17716]: site_fault_detection: disabled 2025-01-30T01:54:25.709431+07:00 PPL404I-112 nutdrv_qx[17716]: max_bypass_volt: 264 2025-01-30T01:54:25.710861+07:00 PPL404I-112 nutdrv_qx[17716]: max_bypass_volt, settable range: 230..264 2025-01-30T01:54:25.712361+07:00 PPL404I-112 nutdrv_qx[17716]: min_bypass_volt: 170 2025-01-30T01:54:25.713857+07:00 PPL404I-112 nutdrv_qx[17716]: min_bypass_volt, settable range: 170..220 2025-01-30T01:54:25.989422+07:00 PPL404I-112 nutdrv_qx[17716]: max_bypass_freq: 53.0 2025-01-30T01:54:25.989803+07:00 PPL404I-112 nutdrv_qx[17716]: max_bypass_freq, settable range: 51.0..60.0 2025-01-30T01:54:25.990284+07:00 PPL404I-112 nutdrv_qx[17716]: min_bypass_freq: 47.0 2025-01-30T01:54:25.993525+07:00 PPL404I-112 nutdrv_qx[17716]: min_bypass_freq, settable range: 40.0..49.0 2025-01-30T01:54:26.700544+07:00 PPL404I-112 nutdrv_qx[17754]: Startup successful 2025-01-30T01:54:28.395427+07:00 PPL404I-112 upsd-usbd[5564]: Connected to UPS [pcmusb]: nutdrv_qx-pcmusb 2025-01-30T01:54:28.397038+07:00 PPL404I-112 nutdrv_qx[17754]: sock_connect: enabling asynchronous mode (auto) 2025-01-30T02:01:00.297648+07:00 PPL404I-112 crond[2480]: USER root pid 25919 cmd run-parts /opt/pp/CLI/sbin/etc/cron.daily 2025-01-30T02:05:03.093080+07:00 PPL404I-112 : [origin software="rsyslogd" swVersion="8.2110.0" x-pid="2343" x-info="https://www.rsyslog.com"] rsyslogd was HUPed 2025-01-30T02:08:00.304456+07:00 PPL404I-112 crond[2480]: USER root pid 2283 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T03:08:00.350284+07:00 PPL404I-112 crond[2480]: USER root pid 13312 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T04:08:00.395500+07:00 PPL404I-112 crond[2480]: USER root pid 24215 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T04:43:41.028658+07:00 PPL404I-112 upsd-usbd[5564]: Data for UPS [pcmusb] is stale - check driver 2025-01-30T04:43:41.075539+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-30T04:43:41.144944+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-30T04:43:41.283605+07:00 PPL404I-112 upsd-usbd[5564]: Can't connect to UPS [pcmusb] (nutdrv_qx-pcmusb): Connection refused 2025-01-30T04:43:44.277374+07:00 PPL404I-112 nutdrv_qx[4699]: device.serial: UPS reported a non-significant serial [0000000000000000] 2025-01-30T04:43:45.453611+07:00 PPL404I-112 nutdrv_qx[4699]: battery_number: 3 2025-01-30T04:43:45.454973+07:00 PPL404I-112 nutdrv_qx[4699]: battery_number, settable range: 1..9 2025-01-30T04:43:46.214688+07:00 PPL404I-112 nutdrv_qx[4699]: bypass_alarm: enabled 2025-01-30T04:43:46.216116+07:00 PPL404I-112 nutdrv_qx[4699]: battery_alarm: enabled 2025-01-30T04:43:46.217471+07:00 PPL404I-112 nutdrv_qx[4699]: bypass_when_off: enabled 2025-01-30T04:43:46.219211+07:00 PPL404I-112 nutdrv_qx[4699]: alarm_control: enabled 2025-01-30T04:43:46.220618+07:00 PPL404I-112 nutdrv_qx[4699]: converter_mode: disabled 2025-01-30T04:43:46.222514+07:00 PPL404I-112 nutdrv_qx[4699]: eco_mode: enabled 2025-01-30T04:43:46.224090+07:00 PPL404I-112 nutdrv_qx[4699]: bypass_forbidding: disabled 2025-01-30T04:43:46.224472+07:00 PPL404I-112 nutdrv_qx[4699]: site_fault_detection: disabled 2025-01-30T04:43:46.773409+07:00 PPL404I-112 nutdrv_qx[4699]: max_bypass_volt: 264 2025-01-30T04:43:46.773587+07:00 PPL404I-112 nutdrv_qx[4699]: max_bypass_volt, settable range: 230..264 2025-01-30T04:43:46.773722+07:00 PPL404I-112 nutdrv_qx[4699]: min_bypass_volt: 170 2025-01-30T04:43:46.773894+07:00 PPL404I-112 nutdrv_qx[4699]: min_bypass_volt, settable range: 170..220 2025-01-30T04:43:46.909420+07:00 PPL404I-112 nutdrv_qx[4699]: max_bypass_freq: 53.0 2025-01-30T04:43:46.909821+07:00 PPL404I-112 nutdrv_qx[4699]: max_bypass_freq, settable range: 51.0..60.0 2025-01-30T04:43:46.910316+07:00 PPL404I-112 nutdrv_qx[4699]: min_bypass_freq: 47.0 2025-01-30T04:43:46.910654+07:00 PPL404I-112 nutdrv_qx[4699]: min_bypass_freq, settable range: 40.0..49.0 2025-01-30T04:43:47.628649+07:00 PPL404I-112 nutdrv_qx[4748]: Startup successful 2025-01-30T04:43:49.292661+07:00 PPL404I-112 upsd-usbd[5564]: Connected to UPS [pcmusb]: nutdrv_qx-pcmusb 2025-01-30T04:43:49.292955+07:00 PPL404I-112 nutdrv_qx[4748]: sock_connect: enabling asynchronous mode (auto) 2025-01-30T05:08:00.441559+07:00 PPL404I-112 crond[2480]: USER root pid 3063 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T06:08:00.491364+07:00 PPL404I-112 crond[2480]: USER root pid 14514 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T07:08:00.536049+07:00 PPL404I-112 crond[2480]: USER root pid 26753 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T08:08:00.584456+07:00 PPL404I-112 crond[2480]: USER root pid 6113 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly 2025-01-30T08:43:17.965297+07:00 PPL404I-112 upsd-usbd[5564]: Data for UPS [pcmusb] is stale - check driver 2025-01-30T08:43:19.359901+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-30T08:43:19.422231+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-30T08:43:19.564271+07:00 PPL404I-112 upsd-usbd[5564]: Can't connect to UPS [pcmusb] (nutdrv_qx-pcmusb): Connection refused 2025-01-30T08:43:22.557374+07:00 PPL404I-112 nutdrv_qx[19246]: device.serial: UPS reported a non-significant serial [0000000000000000] 2025-01-30T08:43:23.765612+07:00 PPL404I-112 nutdrv_qx[19246]: battery_number: 3 2025-01-30T08:43:23.766978+07:00 PPL404I-112 nutdrv_qx[19246]: battery_number, settable range: 1..9 2025-01-30T08:43:24.543252+07:00 PPL404I-112 nutdrv_qx[19246]: bypass_alarm: enabled 2025-01-30T08:43:24.544674+07:00 PPL404I-112 nutdrv_qx[19246]: battery_alarm: enabled 2025-01-30T08:43:24.546035+07:00 PPL404I-112 nutdrv_qx[19246]: bypass_when_off: enabled 2025-01-30T08:43:24.547799+07:00 PPL404I-112 nutdrv_qx[19246]: alarm_control: enabled 2025-01-30T08:43:24.549196+07:00 PPL404I-112 nutdrv_qx[19246]: converter_mode: disabled 2025-01-30T08:43:24.551103+07:00 PPL404I-112 nutdrv_qx[19246]: eco_mode: enabled 2025-01-30T08:43:24.552596+07:00 PPL404I-112 nutdrv_qx[19246]: bypass_forbidding: disabled 2025-01-30T08:43:24.553053+07:00 PPL404I-112 nutdrv_qx[19246]: site_fault_detection: disabled 2025-01-30T08:43:25.125411+07:00 PPL404I-112 nutdrv_qx[19246]: max_bypass_volt: 264 2025-01-30T08:43:25.126868+07:00 PPL404I-112 nutdrv_qx[19246]: max_bypass_volt, settable range: 230..264 2025-01-30T08:43:25.128329+07:00 PPL404I-112 nutdrv_qx[19246]: min_bypass_volt: 170 2025-01-30T08:43:25.129740+07:00 PPL404I-112 nutdrv_qx[19246]: min_bypass_volt, settable range: 170..220 2025-01-30T08:43:25.285444+07:00 PPL404I-112 nutdrv_qx[19246]: max_bypass_freq: 53.0 2025-01-30T08:43:25.286864+07:00 PPL404I-112 nutdrv_qx[19246]: max_bypass_freq, settable range: 51.0..60.0 2025-01-30T08:43:25.287303+07:00 PPL404I-112 nutdrv_qx[19246]: min_bypass_freq: 47.0 2025-01-30T08:43:25.287744+07:00 PPL404I-112 nutdrv_qx[19246]: min_bypass_freq, settable range: 40.0..49.0 2025-01-30T08:43:26.013652+07:00 PPL404I-112 nutdrv_qx[19316]: Startup successful 2025-01-30T08:43:27.572294+07:00 PPL404I-112 upsd-usbd[5564]: Connected to UPS [pcmusb]: nutdrv_qx-pcmusb 2025-01-30T08:43:27.572522+07:00 PPL404I-112 nutdrv_qx[19316]: sock_connect: enabling asynchronous mode (auto) 2025-01-30T08:43:58.363133+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-30T08:50:16.427930+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-30T08:56:57.509560+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-30T08:57:00.918761+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-30T08:57:04.340224+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-30T08:57:07.776708+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-30T08:57:11.240717+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-30T08:57:48.760184+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link down 2025-01-30T08:57:52.214808+07:00 PPL404I-112 root: rt3050-esw 10110000.esw: link changed: LAN2 link up 2025-01-30T09:00:21.250190+07:00 PPL404I-112 upsd-usbd[5564]: Data for UPS [pcmusb] is stale - check driver 2025-01-30T09:00:21.302316+07:00 PPL404I-112 u_main.pl: Uupsd: cannot get data from ups retry:1/3 2025-01-30T09:00:21.372934+07:00 PPL404I-112 u_main.pl: Uupsd: Defined UPS's USBVIDPID has been found:restore connection 2025-01-30T09:00:21.515464+07:00 PPL404I-112 upsd-usbd[5564]: Can't connect to UPS [pcmusb] (nutdrv_qx-pcmusb): Connection refused 2025-01-30T09:00:24.213375+07:00 PPL404I-112 nutdrv_qx[8257]: device.serial: UPS reported a non-significant serial [0000000000000000] 2025-01-30T09:00:25.373642+07:00 PPL404I-112 nutdrv_qx[8257]: battery_number: 3 2025-01-30T09:00:25.374988+07:00 PPL404I-112 nutdrv_qx[8257]: battery_number, settable range: 1..9 2025-01-30T09:00:25.998721+07:00 PPL404I-112 nutdrv_qx[8257]: bypass_alarm: enabled 2025-01-30T09:00:26.000129+07:00 PPL404I-112 nutdrv_qx[8257]: battery_alarm: enabled 2025-01-30T09:00:26.001464+07:00 PPL404I-112 nutdrv_qx[8257]: bypass_when_off: enabled 2025-01-30T09:00:26.003245+07:00 PPL404I-112 nutdrv_qx[8257]: alarm_control: enabled 2025-01-30T09:00:26.004640+07:00 PPL404I-112 nutdrv_qx[8257]: converter_mode: disabled 2025-01-30T09:00:26.006533+07:00 PPL404I-112 nutdrv_qx[8257]: eco_mode: enabled 2025-01-30T09:00:26.008002+07:00 PPL404I-112 nutdrv_qx[8257]: bypass_forbidding: disabled 2025-01-30T09:00:26.008371+07:00 PPL404I-112 nutdrv_qx[8257]: site_fault_detection: disabled 2025-01-30T09:00:26.549411+07:00 PPL404I-112 nutdrv_qx[8257]: max_bypass_volt: 264 2025-01-30T09:00:26.550831+07:00 PPL404I-112 nutdrv_qx[8257]: max_bypass_volt, settable range: 230..264 2025-01-30T09:00:26.552269+07:00 PPL404I-112 nutdrv_qx[8257]: min_bypass_volt: 170 2025-01-30T09:00:26.553747+07:00 PPL404I-112 nutdrv_qx[8257]: min_bypass_volt, settable range: 170..220 2025-01-30T09:00:26.685511+07:00 PPL404I-112 nutdrv_qx[8257]: max_bypass_freq: 53.0 2025-01-30T09:00:26.685894+07:00 PPL404I-112 nutdrv_qx[8257]: max_bypass_freq, settable range: 51.0..60.0 2025-01-30T09:00:26.686376+07:00 PPL404I-112 nutdrv_qx[8257]: min_bypass_freq: 47.0 2025-01-30T09:00:26.686700+07:00 PPL404I-112 nutdrv_qx[8257]: min_bypass_freq, settable range: 40.0..49.0 2025-01-30T09:00:27.513701+07:00 PPL404I-112 nutdrv_qx[8295]: Startup successful 2025-01-30T09:00:27.522277+07:00 PPL404I-112 upsd-usbd[5564]: Connected to UPS [pcmusb]: nutdrv_qx-pcmusb 2025-01-30T09:00:27.829782+07:00 PPL404I-112 nutdrv_qx[8295]: sock_connect: enabling asynchronous mode (auto) 2025-01-30T09:08:00.631083+07:00 PPL404I-112 crond[2480]: USER root pid 18057 cmd run-parts /opt/pp/CLI/sbin/etc/cron.hourly
Greg Troxel
2025-Jan-31 12:19 UTC
[Nut-upsdev] Error "Data for UPS [pcmusb] is stale - check driver"
"Rushabh Sanghavi (Rush)" <Rushabh at pp-ontime.co.th> writes:> * NUT Version 2.8.0-3 was installed on our 4G LTE WiFi router by our team.You have two problems right there. Most importantly, the most recent release of nut is 2.8.2, from April of 2024. 2.8.0 is from April of 2022. Many things have been fixed. I personally do not engage in troubleshooting out of date code. (There have also been fixes since 2.8.2; there are 1658 commits on master after the v2.8.2 tag.) Secondly, there is no nut version 2.8.0-3. That is almost certainly the version of a package provided by some packaging system. Therefore, my advice is to build current nut sources from git master and test those. Perhaps also 2.8.2.> Awaiting your swift response back.Perhaps you have a support contract with somebody (in which case this should ahve been sent to them and not the list), but assuming that's not true, please keep in mind that you have received software at no charge and now you are asking for help at no charge. Also, your email belonged on nut-upsuser instaed of nut-upsdev. I suggest you start over there after you have compiled and tested with up to date code.> Confidentiality: This Information is intended for the above-named > person and may contain confidential and/or legally privileged > material. Any opinions expressed in this information are not > necessarily those of the company. If it has come to you in error you > must take no action based on it, nor must you copy or show it to > anyone; please delete/destroy and inform the sender immediately.You've posted to a public list. Please fix your mail system so that you do not include nonsensical disclaimers and demands in such mail.
Ted Mittelstaedt
2025-Feb-02 18:18 UTC
[Nut-upsdev] Error "Data for UPS [pcmusb] is stale - check driver"
OpenWRT version 23.05.0-rc3 is, for starters, not supported anymore by the OpenWRT project, and is old. The current version is OpenWRT 23.05.05 The reason you are likely getting an old version of NUT when you load the nut package is because you are using an old version of openwrt. Your team needs to sysupdate your 4G LTE Wifi router You also, in my opinion, need to seriously reconsider running NUT on an openwrt router.? The reason why is that NUT generates logfiles and writes to the filesystem. The flash chips that are used on routers are not designed like a USB flash stick where they are intended to have a read/write filesystem on them.? They have no bad block management with NAND flash chips.? That is provided by a UBI layer.? You can read about that here: [OpenWrt Wiki] The OpenWrt Flash Layout <https://openwrt.org/docs/techref/flash.layout> SOME of the NAND devices that OpenWRT has been ported to, DO have complete UBI support, others don't.? You did not say what model of router you are running - but unless you have researched it and are completely sure that it has a fully functional bad block management, you can easily cause problems over time attempting to run programs on an OpenWRT router. In general it's safest to run READ ONLY programs on openwrt.? For example, the snmpd server.? Programs that WRITE to the filesystem on the OpenWRT router should be avoided. There's a reason we use hard drives on servers. Ted On 1/30/2025 7:50 PM, Rushabh Sanghavi (Rush) wrote:> > Dear NUT Developers, > > A very good morning to you and hope that you are in the best of health > and spirits. > > For an upcoming UPS Project, our team has been testing Powercom?s > Cleanline T-1500 UPS model whose photo has been attached with this > e-mail. Our team has been testing this UPS with one of our 4G LTE WiFi > router models on which Network UPS Tools (NUT) Version 2.8.0-3 has > been installed. BUT during the testing our team observed multiple > instances of error message *"Data for UPS [pcmusb] is stale - check > driver"* being randomly reported by our 4G LTE WiFi router. Here is > the SUMMARY of the issue below for clear understanding purposes. > > * NUT Version 2.8.0-3 was installed on our 4G LTE WiFi router by our > team. > * Also our 4G LTE WiFi router had Linux Kernel Version 5.15.127, > OpenWRT Distribution release ?23.05.0-rc3? and OpenWRT > Distribution Revision ?r23389-5deed175a5? installed on it. > * Powercom?s Cleanline T-1500 UPS was connected with our 4G LTE WiFi > router via USB to USB Cable Connection (i.e. USB Port on router > side and USB Port on UPS side) > > Now when NUT installed on our 4G LTE WiFi router model unit tried to > poll and fetch values of different UPS parameters from Powercom?s > Cleanline T-1500 UPS model > > after both UPS and router had been running for sometime (i.e. for > random period of time): > > o router started reporting the error message *?Data for UPS > [pcmusb] is stale - check driver?* > o after that router could not get UPS?s status any more unless > we restart the NUT service > o and the router started reporting the error message ?Data for > UPS [pcmusb] is stale - check driver? after running for > sometime again > > Note: *[pcmusb]* represents the *name or identifier* assigned to the > UPS instance within the NUT (Network UPS Tools) configuration > > * Our team tried to increase value of NUT?s timers such as > ?pollinterval?, ?pollfreq?, ?maxage? but still the issue could not > get solved or fixed > * Kindly NOTE that our team tested the above with both the NUT > Drivers i.e. blazer_usb and nutdrv_qx. But the same error message > mentioned above was observed. > * Also kindly NOTE that our team also tried to test with NUT Driver > ?usbhid-ups? but it is seems that this particular Driver is not > supported by Powercom?s Cleanline T-1500 UPS model whose photo has > been attached with this e-mail. > * Currently our team is not 100% sure about the exact root cause. > > Our team need to know the following from NUT Developers. > > * Which the is correct NUT Driver that our team need to use on the > 4G LTE WiFi router so that it can communicate smoothly and > successfully with Powercom?s Cleanline T-1500 UPS model whose > photo has been attached with this e-mail? > * Which specific parameters within the default Configuration > Settings file of NUT Version 2.8.0-3 on our 4G LTE WiFi router > need to be tweaked / changed so that our 4G LTE WiFi router model > can communicate with the Powercom?s Cleanline T-1500 UPS model > smoothly and successfully? > * Which specific parameters within the default ups.conf / upsd.conf > file on our 4G LTE WiFi router needs to be tweaked / changed so > that our 4G LTE WiFi router model can communicate with the > Powercom?s Cleanline T-1500 UPS model smoothly and successfully? > > Also I am hereby attaching the Log Files with the Log Messages > reported on our 4G LTE WiFi router model. The 1st Log file contains > Log Messages during testing with NUT Driver ?blazer_usb? while the 2nd > Log file contains Log Messages during testing with NUT Driver > ?nutdrv_qx?. You will observe the ERROR Message *?Data for UPS > [pcmusb] is stale - check driver?* within both these attached Log Files. > > Awaiting your swift response back. > > Thanking you, > > Yours sincerely, > > Legs Logo > > *Rushabh N. S*** > > *Research and Development Director* > > *PP Ontime Company Limited* > > *PP Group of Companies* > > Address: 1011 Supalai Grand Tower, > > 16th Floor, Rama 3 Road, > > Chongnonsi, Yannawa, > > Bangkok ? 10120, Thailand > > Landline No: +66-2-0562099 Ext. 2201 > > Fax No: +66-2-0562088 > > Cell Phone No: +66-8-59118578 / +66-6-22236221 > > E-mail: rushabh at pp-ontime.co.th <mailto:rushabh at pp-ontime.co.th> > > Web: www.pp-ontime.co.th <http://www.pp-ontime.co.th> > > Skype ID: rushabh.sanghavi > > *Disclaimer:* > > *************************************************************** > *Important* > Confidentiality: This Information is intended for the above-named > person and may contain confidential and/or legally privileged > material. Any opinions expressed in this information are not > necessarily those of the company. If it has come to you in error you > must take no action based on it, nor must you copy or show it to > anyone; please delete/destroy and inform the sender immediately. > > *Monitoring/Viruses/Malwares* > PP-Ontime reserves the right to monitor all incoming and outgoing > emails via PP-Ontime's systems. Although we have security program to > monitor and eliminate virus/malware, we also advise that in keeping > with good computing practice the recipient should ensure they are > actually virus/malwares free. > *************************************************************** > > > Disclaimer: > > *********************************************************************************************** > *Important* > Confidentiality: This Information is intended for the above-named > person and may contain confidential and/or legally privileged > material. Any opinions expressed in this information are not > necessarily those of the company. If it has come to you in error you > must take no action based on it, nor must you copy or show it to > anyone; please delete/destroy and inform the sender immediately. > *Monitoring/Viruses/Malwares* > PP-Ontime reserves the right to monitor all incoming and outgoing > emails via PP-Ontime's systems. Although we have security program to > monitor and eliminate virus/malware, we also advise that in keeping > with good computing practice the recipient should ensure they are > actually virus/malwares free. > ********************************************************************************************** > > > _______________________________________________ > Nut-upsdev mailing list > Nut-upsdev at alioth-lists.debian.net > https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsdev-------------- next part -------------- An HTML attachment was scrubbed... URL: <http://alioth-lists.debian.net/pipermail/nut-upsdev/attachments/20250202/912b555b/attachment-0001.htm> -------------- next part -------------- A non-text attachment was scrubbed... Name: image001.jpg Type: image/jpeg Size: 4031 bytes Desc: not available URL: <http://alioth-lists.debian.net/pipermail/nut-upsdev/attachments/20250202/912b555b/attachment-0001.jpg>