asterisk users - Feb 2013 - Can't detect remote answer

I'm attempting to place an outgoing call over POTS/DAHDI, it dials without
problem but the remote answer isn't tried.

So far I've attempted:

   - Searching on google
   - Enabling full and verbose logging (including the debug option of the
   DAHDI module) - showing NO event at the time I answer on the remote phone
   a.k.a "my mobile"
   - Using another phone on the same line - it works
   - Receiving a call on that line - no problem
   - Logging DTMF - it shows digits dialled on my mobile, after I've
   answered, even whilst it seems to still be ringing locally
   - Looking on the wiki
   - Asking on IRC

So far, I've found nothing that helps.

A sample log output is here: http://pastebin.com/cprZSy9i
And my chan_dahdi.conf: http://pastebin.com/L7mBJ66Y
And dahdi system.conf: http://pastebin.com/6UQPVC9x
also in modprobe.d/dahdi.conf: http://pastebin.com/5ZqtcZdj

*any* advice/suggestions at this point would be very much appreciated!




-- 
Kevin Wright
mail: kevin.wright at scalatechnology.com
gtalk / msn : kev.lee.wright at gmail.com
quora: http://www.quora.com/Kevin-Wright
google+: http://gplus.to/thecoda
<kev.lee.wright at gmail.com>
twitter: @thecoda
vibe / skype: kev.lee.wright
steam: kev_lee_wright

"My point today is that, if we wish to count lines of code, we should not
regard them as "lines produced" but as "lines spent": the
current
conventional wisdom is so foolish as to book that count on the wrong side
of the ledger" ~ Dijkstra
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://lists.digium.com/pipermail/asterisk-users/attachments/20130211/6c8bf6ca/attachment.htm>

I forgot to add, cat /proc/dahdi/* yields:

Span 1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER)

   1 WCTDM/4/0 FXSKS (In use) (EC: MG2 - INACTIVE)
   2 WCTDM/4/1 FXOKS (EC: MG2 - INACTIVE)
   3 WCTDM/4/2 Reserved
   4 WCTDM/4/3 Reserved


I'm not sure if that (in use) is correct when I'm not actively in a
call.

This is a very sensitive setup, as a home installation it absolutely *must*
pass the gruelling "wife test", so I'm keen to see it up and
running
properly :)


On 11 February 2013 16:50, Kevin Wright <kev.lee.wright at gmail.com>
wrote:
>
> I'm attempting to place an outgoing call over POTS/DAHDI, it dials
without
> problem but the remote answer isn't tried.
>
> So far I've attempted:
>
>    - Searching on google
>    - Enabling full and verbose logging (including the debug option of the
>    DAHDI module) - showing NO event at the time I answer on the remote
phone
>    a.k.a "my mobile"
>    - Using another phone on the same line - it works
>    - Receiving a call on that line - no problem
>    - Logging DTMF - it shows digits dialled on my mobile, after I've
>    answered, even whilst it seems to still be ringing locally
>    - Looking on the wiki
>    - Asking on IRC
>
> So far, I've found nothing that helps.
>
> A sample log output is here: http://pastebin.com/cprZSy9i
> And my chan_dahdi.conf: http://pastebin.com/L7mBJ66Y
> And dahdi system.conf: http://pastebin.com/6UQPVC9x
> also in modprobe.d/dahdi.conf: http://pastebin.com/5ZqtcZdj
>
> *any* advice/suggestions at this point would be very much appreciated!
>
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://lists.digium.com/pipermail/asterisk-users/attachments/20130211/b3c17c0e/attachment.htm>