thr3ads.net - asterisk users - [asterisk-users] User busy issue in A400P 4 FXO card [Jan 2013]

If this information is useful, please help other people find it:
Share via:

Selva M

2013-Jan-03 06:23 UTC

[asterisk-users] User busy issue in A400P 4 FXO card

Hi,

 I setup PBX with A400P 4 x FXo board. There are one analog line plugged
into port 1.

 Internal extension cane make calls to PSTN without any issue.

 When I make inbound call, caller get busy tone "user busy' message
right
away.

 Asterisk log shows following log and internal extension (200) rings for
that call and hangup (log below).

  I tested the system with some other service provider and it worked fine
for IB and OB calls.

   i would like to get your feedback to resolve the issue and will
appreciate your feedback.

Thanks
Selva


[PBX1.localdomain dahdi]# lsdahdi
### Span  1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER)
  1 FXO        FXSKS       (In use) (SWEC: MG2)
  2 FXO        FXSKS       (In use) (SWEC: MG2)  RED
  3 FXO        FXSKS       (In use) (SWEC: MG2)  RED
  4 FXO        FXSKS       (In use) (SWEC: MG2)  RED


PBX1*CLI> dahdi show regdump 1
Direct registers:
  0. 00    1. 00    2. 03    3. 00    4. e9    5. 08    6. 00    7. 00
  8. 00    9. 00   10. 00   11. 35   12. 40   13. 58   14. 00   15. 00
 16. 01   17. 02   18. 00   19. 02   20. 00   21. 00   22. 96   23. 2d
 24. 19   25. 08   26. c0   27. 05   28. 00   29. 34   30. 00   31. a3
 32. 07   33. 28   34. 18   35. 00   36. 18   37. 00   38. 10   39. 10
 40. 10   41. 10   42. 00   43. 00   44. 00   45. 00   46. 00   47. 00
 48. 00   49. 00   50. 00   51. 00   52. 00   53. 00   54. 00   55. 00
 56. 0f   57. 00   58. 00   59. 00

TIP: 52.0000 Volts
RING: 52.0000 Volts
VBAT: 52.0000 Volts

PBX1*CLI> dahdi show regdump 2
Direct registers:
  0. 00    1. 00    2. 03    3. 00    4. 29    5. 08    6. 00    7. 00
  8. 00    9. 00   10. 00   11. 35   12. 40   13. 58   14. 00   15. 00
 16. 01   17. 00   18. 00   19. 02   20. 00   21. 00   22. 96   23. 2d
 24. 19   25. 08   26. c0   27. 07   28. 00   29. 01   30. 00   31. a3
 32. 07   33. 28   34. 10   35. 00   36. 10   37. 00   38. 10   39. 10
 40. 10   41. 10   42. 00   43. 00   44. 00   45. 00   46. 00   47. 00
 48. 00   49. 00   50. 00   51. 00   52. 00   53. 00   54. 00   55. 00
 56. 0f   57. 00   58. 00   59. 00

TIP:  1.0000 Volts
RING:  1.0000 Volts
VBAT:  1.0000 Volts



-----------------------------------------------------------------------------------------------------------------------------------------------------


 -- Starting simple switch on 'DAHDI/1-1'
    -- Executing [s at from-pstn:1] Set("DAHDI/1-1",
"__FROM_DID=s") in new
stack
    -- Executing [s at from-pstn:2] Gosub("DAHDI/1-1",
"app-blacklist-check,s,1")
i
n new stack
    -- Executing [s at app-blacklist-check:1] GotoIf("DAHDI/1-1",
"0?blacklisted")
in new stack
    -- Executing [s at app-blacklist-check:2] Return("DAHDI/1-1",
"") in new
stack
    -- Executing [s at from-pstn:3] ExecIf("DAHDI/1-1", "1
?Set(CALLERID(name)=)")
in new stack
    -- Executing [s at from-pstn:4] Set("DAHDI/1-1",
"__CALLINGPRES_SV=allowed_not_
screened") in new stack
    -- Executing [s at from-pstn:5] Set("DAHDI/1-1",
"CALLERPRES()=allowed_not_scre
ened") in new stack
    -- Executing [s at from-pstn:6] Goto("DAHDI/1-1",
"from-did-direct,200,1")
in
n
ew stack
    -- Goto (from-did-direct,200,1)
    -- Executing [200 at from-did-direct:1] Macro("DAHDI/1-1",
"exten-vm,200,200")
in new stack
    -- Executing [s at macro-exten-vm:1] Macro("DAHDI/1-1",
"user-callerid")
in
new
stack
    -- Executing [s at macro-user-callerid:1] Set("DAHDI/1-1",
"AMPUSER=") in
new
s
tack
    -- Executing [s at macro-user-callerid:2] GotoIf("DAHDI/1-1",
"0?report")
in
ne
w stack
    -- Executing [s at macro-user-callerid:3] ExecIf("DAHDI/1-1",
"1?Set(REALCALLER
IDNUM=)") in new stack
    -- Executing [s at macro-user-callerid:4] Set("DAHDI/1-1",
"AMPUSER=") in
new
s
tack
    -- Executing [s at macro-user-callerid:5] Set("DAHDI/1-1",
"AMPUSERCIDNAME=")
i
n new stack
    -- Executing [s at macro-user-callerid:6] GotoIf("DAHDI/1-1",
"1?report")
in
ne
w stack
    -- Goto (macro-user-callerid,s,10)
    -- Executing [s at macro-user-callerid:10] GotoIf("DAHDI/1-1",
"0?continue")
in
new stack
    -- Executing [s at macro-user-callerid:11] Set("DAHDI/1-1",
"__TTL=64") in
new
stack
    -- Executing [s at macro-user-callerid:12] GotoIf("DAHDI/1-1",
"1?continue")
in
new stack
    -- Goto (macro-user-callerid,s,19)
    -- Executing [s at macro-user-callerid:19] NoOp("DAHDI/1-1",
"Using
CallerID
""
<>") in new stack
    -- Executing [s at macro-exten-vm:2] Set("DAHDI/1-1",
"RingGroupMethod=none")
i
n new stack
    -- Executing [s at macro-exten-vm:3] Set("DAHDI/1-1",
"VMBOX=200") in new
stack
    -- Executing [s at macro-exten-vm:4] Set("DAHDI/1-1",
"EXTTOCALL=200") in
new
s
tack
    -- Executing [s at macro-exten-vm:5] Set("DAHDI/1-1",
"CFUEXT=") in new
stack
    -- Executing [s at macro-exten-vm:6] Set("DAHDI/1-1",
"CFBEXT=") in new
stack
    -- Executing [s at macro-exten-vm:7] Set("DAHDI/1-1",
"RT=15") in new stack
    -- Executing [s at macro-exten-vm:8] Macro("DAHDI/1-1",
"record-enable,200,IN")
in new stack
    -- Executing [s at macro-record-enable:1] GotoIf("DAHDI/1-1",
"1?check")
in
new
stack
    -- Goto (macro-record-enable,s,4)
    -- Executing [s at macro-record-enable:4] AGI("DAHDI/1-1",
"recordingcheck,2013
0103-002934,1357190966.4") in new stack
    -- Launched AGI Script /var/lib/asterisk/agi-bin/recordingcheck
 recordingcheck,20130103-002934,1357190966.4: Inbound recording not enabled
    -- <DAHDI/1-1>AGI Script recordingcheck completed, returning 0
    -- Executing [s at macro-record-enable:5] MacroExit("DAHDI/1-1",
"") in
new
sta
ck
    -- Executing [s at macro-exten-vm:9] Macro("DAHDI/1-1",
"dial,15,tr,200")
in
ne
w stack
    -- Executing [s at macro-dial:1] GotoIf("DAHDI/1-1",
"1?dial") in new stack
    -- Goto (macro-dial,s,3)
    -- Executing [s at macro-dial:3] AGI("DAHDI/1-1",
"dialparties.agi") in
new
sta
ck
    -- Launched AGI Script /var/lib/asterisk/agi-bin/dialparties.agi
 dialparties.agi: Starting New Dialparties.agi
 dialparties.agi: Caller ID name is 'unknown' number is
'unknown'
       > dialparties.agi: USE_CONFIRMATION:  'FALSE'
       > dialparties.agi: RINGGROUP_INDEX:   ''
 dialparties.agi: Methodology of ring is  'none'
    -- dialparties.agi: Added extension 200 to extension map
       > dialparties.agi: Extension 200 has call screening off
    -- dialparties.agi: Extension 200 cf is disabled
    -- dialparties.agi: Extension 200 do not disturb is disabled
       > dialparties.agi: extnum 200 has:  cw: 1; hascfb: 0 [] hascfu: 0 []
 dialparties.agi: EXTENSION_STATE: 0 (NOT_INUSE)
    -- dialparties.agi: DbDel CALLTRACE/200 - Caller ID is not defined
    -- dialparties.agi: Filtered ARG3: 200
    -- <DAHDI/1-1>AGI Script dialparties.agi completed, returning 0
    -- Executing [s at macro-dial:7] Dial("DAHDI/1-1",
"SIP/200,15,tr") in new
stac
k
  == Using SIP RTP TOS bits 184
  == Using SIP RTP CoS mark 5
  == Using SIP VRTP TOS bits 136
  == Using SIP VRTP CoS mark 6
    -- Called 200
<< [ TYPE: Control (4) SUBCLASS: Ringing (3) ] [SIP/200-00000002]
    -- SIP/200-00000002 is ringing
<< [ TYPE: Control (4) SUBCLASS: Ringing (3) ] [SIP/200-00000002]
    -- SIP/200-00000002 is ringing
<< [ HANGUP (NULL) ] [DAHDI/1-1]
  == Spawn extension (macro-dial, s, 7) exited non-zero on 'DAHDI/1-1'
in
macro
'dial'
  == Spawn extension (macro-exten-vm, s, 9) exited non-zero on
'DAHDI/1-1'
in
ma
cro 'exten-vm'
  == Spawn extension (from-did-direct, 200, 1) exited non-zero on
'DAHDI/1-1'
    -- Hungup 'DAHDI/1-1'
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://lists.digium.com/pipermail/asterisk-users/attachments/20130103/81eb525c/attachment-0001.htm>

A J Stiles

2013-Jan-03 09:44 UTC

head link

[asterisk-users] User busy issue in A400P 4 FXO card

On Thursday 03 January 2013, Selva M wrote:> Hi,
> 
>  I setup PBX with A400P 4 x FXo board. There are one analog line plugged
> into port 1.
> 
>  Internal extension cane make calls to PSTN without any issue.
> 
>  When I make inbound call, caller get busy tone "user busy'
message right
> away.
> 
>  Asterisk log shows following log and internal extension (200) rings for
> that call and hangup (log below).
> 
>   I tested the system with some other service provider and it worked fine
> for IB and OB calls.
> 
>    i would like to get your feedback to resolve the issue and will
> appreciate your feedback.
> 
> Thanks
> Selva
Don't try to run before you can walk.  First of all, simplify your dialplan 
right down to the minimum.  Have just this context for calls coming in from 
the card:

[from-pstn]
s,1,NoOp(Incoming call from ${CALLERID(num)})
s,2,Dial(200)
s,3,Hangup()
; end of from-pstn context

This will write the caller's number to the console  (step 1)  and ring 
extension 200  (step 2).  Alter it if necessary.  Do a reload, and call 
yourself from your mobile  (or get an assistant to call you)  while watching 
the console.

If it doesn't work, you have a DAHDI problem; most probably your country 
settings are wrong  (NB: in some countries, different telephone companies can 
actually require different country settings!)  Power your machine off and on 
again after changing DAHDI settings, just to make absolutely sure that it 
really is using the new ones.

Once you have that very simple dialplan working, then you can start 
introducing extra bells and whistles; one at a time, and testing in between 
each one and the next.

-- 
AJS

Answers come *after* questions.

asterisk users - Jan 2013 - User busy issue in A400P 4 FXO card

[asterisk-users] User busy issue in A400P 4 FXO card

[asterisk-users] User busy issue in A400P 4 FXO card