Dear All, I am trying to setup an ISDN line from local telco on a digium card. The problem I am facing is that I am not getting any caller id from the telco. They say that they have enabled caller id. Please help me out. My zapata.conf -------------------------------------------------------------------------------------------------------------------- [trunkgroups] [channels] context=pstnincoming pridialplan=local prilocaldialplan=local usecallerid=yes cidsignalling=v23 cidstart=ring hidecallerid=no callwaiting=no usecallingpres=yes sendcalleridafter=1 echocancel=no echocancelwhenbridged=no rxgain=0.0 txgain=0.0 callgroup=1 pickupgroup=1 immediate=no callerid=asreceived busydetect=no busycount=6 callprogress=no faxdetect=incoming switchtype = national signalling = pri_cpe group = 1 channel => 1-15,17-31 channel => 32-46,48-62 -------------------------------------------------------------------------------------------------------------------- The information I get from using "pri intense debug span 1" is: -------------------------------------------------------------------------------------------------------------------- < [ 02 01 16 9c 08 02 15 01 05 04 03 80 90 a3 18 03 a1 83 81 70 08 c1 34 33 39 32 38 34 32 a1 ] < Informational frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < N(S): 011 0: 0 < N(R): 078 P: 0 < 26 bytes of data Handling message for SAPI/TEI=0/0 -- ACKing all packets from 77 to (but not including) 78 -- Since there was nothing left, stopping T200 counter -- Stopping T203 counter since we got an ACK -- Nothing left, starting T203 counter < Protocol Discriminator: Q.931 (8) len=26 < Call Ref: len= 2 (reference 5377/0x1501) (Originator) < Message type: SETUP (5) < [04 03 80 90 a3] < Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer capability: Speech (0) < Ext: 1 Trans mode/rate: 64kbps, circuit-mode (16) < User information layer 1: A-Law (35) < [18 03 a1 83 81] < Channel ID (len= 5) [ Ext: 1 IntID: Implicit PRI Spare: 0 Preferred Dchan: 0 < ChanSel: As indicated in following octets < Ext: 1 Coding: 0 Number Specified Channel Type: 3 < Ext: 1 Channel: 1 ] < [70 08 c1 34 33 39 32 38 34 32] < Called Number (len=10) [ Ext: 1 TON: Subscriber Number (4) NPI: ISDN/Telephony Numbering Plan (E.164/E.163) (1) '4392842' ] < [a1] < Sending Complete (len= 1) -- Making new call for cr 5377 -- Processing Q.931 Call Setup -- Processing IE 4 (cs0, Bearer Capability) -- Processing IE 24 (cs0, Channel Identification) -- Processing IE 112 (cs0, Called Party Number) -- Processing IE 161 (cs0, Sending Complete) q931.c:3509 q931_receive: call 5377 on channel 1 enters state 6 (Call Present) Sending Receiver Ready (12) -------------------------------------------------------------------------------------------------------------------- -- Regards, Nasir.
A.R. Nasir Qureshi wrote:> Dear All, > > I am trying to setup an ISDN line from local telco on a digium card. The > problem I am facing is that I am not getting any caller id from the > telco. They say that they have enabled caller id.Tell them they are wrong. There is no calling party number IE in that SETUP message below. :-) Matthew Fredrickson Digium, Inc.> > Please help me out. > > My zapata.conf > -------------------------------------------------------------------------------------------------------------------- > [trunkgroups] > > [channels] > context=pstnincoming > pridialplan=local > prilocaldialplan=local > > usecallerid=yes > cidsignalling=v23 > cidstart=ring > hidecallerid=no > callwaiting=no > usecallingpres=yes > sendcalleridafter=1 > echocancel=no > echocancelwhenbridged=no > rxgain=0.0 > txgain=0.0 > callgroup=1 > pickupgroup=1 > > immediate=no > callerid=asreceived > busydetect=no > busycount=6 > callprogress=no > faxdetect=incoming > > > switchtype = national > signalling = pri_cpe > group = 1 > channel => 1-15,17-31 > channel => 32-46,48-62 > -------------------------------------------------------------------------------------------------------------------- > > The information I get from using "pri intense debug span 1" is: > -------------------------------------------------------------------------------------------------------------------- > < [ 02 01 16 9c 08 02 15 01 05 04 03 80 90 a3 18 03 a1 83 81 70 08 c1 34 > 33 39 32 38 34 32 a1 ] > > < Informational frame: > < SAPI: 00 C/R: 1 EA: 0 > < TEI: 000 EA: 1 > < N(S): 011 0: 0 > < N(R): 078 P: 0 > < 26 bytes of data > Handling message for SAPI/TEI=0/0 > -- ACKing all packets from 77 to (but not including) 78 > -- Since there was nothing left, stopping T200 counter > -- Stopping T203 counter since we got an ACK > -- Nothing left, starting T203 counter > < Protocol Discriminator: Q.931 (8) len=26 > < Call Ref: len= 2 (reference 5377/0x1501) (Originator) > < Message type: SETUP (5) > < [04 03 80 90 a3] > < Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer > capability: Speech (0) > < Ext: 1 Trans mode/rate: 64kbps, > circuit-mode (16) > < User information layer 1: A-Law (35) > < [18 03 a1 83 81] > < Channel ID (len= 5) [ Ext: 1 IntID: Implicit PRI Spare: 0 > Preferred Dchan: 0 > < ChanSel: As indicated in following octets > < Ext: 1 Coding: 0 Number Specified Channel Type: 3 > < Ext: 1 Channel: 1 ] > < [70 08 c1 34 33 39 32 38 34 32] > < Called Number (len=10) [ Ext: 1 TON: Subscriber Number (4) NPI: > ISDN/Telephony Numbering Plan (E.164/E.163) (1) '4392842' ] > < [a1] > < Sending Complete (len= 1) > -- Making new call for cr 5377 > -- Processing Q.931 Call Setup > -- Processing IE 4 (cs0, Bearer Capability) > -- Processing IE 24 (cs0, Channel Identification) > -- Processing IE 112 (cs0, Called Party Number) > -- Processing IE 161 (cs0, Sending Complete) > q931.c:3509 q931_receive: call 5377 on channel 1 enters state 6 (Call > Present) > Sending Receiver Ready (12) > > -------------------------------------------------------------------------------------------------------------------- >
Dear Matthew, Thank you for your reply. Please tell me if there is any way I can see the actual q931 message received from the card without any translation / filtration / alteration by the software or the driver ? How much the switch type or other configuration variables affect the SETUP message being received ? What I am concerned is that may be the wrong switch type or other parameter may be causing the problem. This is my first attempt at configuring an ISDN, and I want to be sure before I go after the telco. -- Regards, Nasir. A.R. Nasir Qureshi wrote:> > Dear All, > > > > I am trying to setup an ISDN line from local telco on a digium card. The > > problem I am facing is that I am not getting any caller id from the > > telco. They say that they have enabled caller id. >Dear Matthew, Thank you for your reply. Please tell me if there is any way I can see the actual q931 message received from the card without any translation / filtration / alteration by the software or the driver ? How much the switch type or other configuration variables affect the SETUP message ? This is my first attempt at configuring an ISDN, and I want to be sure before I go after the telco. Tell them they are wrong. There is no calling party number IE in that SETUP message below. :-) Matthew Fredrickson Digium, Inc.> > > > Please help me out. > > > > My zapata.conf > > -------------------------------------------------------------------------------------------------------------------- > > [trunkgroups] > > > > [channels] > > context=pstnincoming > > pridialplan=local > > prilocaldialplan=local > > > > usecallerid=yes > > cidsignalling=v23 > > cidstart=ring > > hidecallerid=no > > callwaiting=no > > usecallingpres=yes > > sendcalleridafter=1 > > echocancel=no > > echocancelwhenbridged=no > > rxgain=0.0 > > txgain=0.0 > > callgroup=1 > > pickupgroup=1 > > > > immediate=no > > callerid=asreceived > > busydetect=no > > busycount=6 > > callprogress=no > > faxdetect=incoming > > > > > > switchtype = national > > signalling = pri_cpe > > group = 1 > > channel => 1-15,17-31 > > channel => 32-46,48-62 > > -------------------------------------------------------------------------------------------------------------------- > > > > The information I get from using "pri intense debug span 1" is: > > -------------------------------------------------------------------------------------------------------------------- > > < [ 02 01 16 9c 08 02 15 01 05 04 03 80 90 a3 18 03 a1 83 81 70 08 c1 34 > > 33 39 32 38 34 32 a1 ] > > > > < Informational frame: > > < SAPI: 00 C/R: 1 EA: 0 > > < TEI: 000 EA: 1 > > < N(S): 011 0: 0 > > < N(R): 078 P: 0 > > < 26 bytes of data > > Handling message for SAPI/TEI=0/0 > > -- ACKing all packets from 77 to (but not including) 78 > > -- Since there was nothing left, stopping T200 counter > > -- Stopping T203 counter since we got an ACK > > -- Nothing left, starting T203 counter > > < Protocol Discriminator: Q.931 (8) len=26 > > < Call Ref: len= 2 (reference 5377/0x1501) (Originator) > > < Message type: SETUP (5) > > < [04 03 80 90 a3] > > < Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer > > capability: Speech (0) > > < Ext: 1 Trans mode/rate: 64kbps, > > circuit-mode (16) > > < User information layer 1: A-Law (35) > > < [18 03 a1 83 81] > > < Channel ID (len= 5) [ Ext: 1 IntID: Implicit PRI Spare: 0 > > Preferred Dchan: 0 > > < ChanSel: As indicated in following octets > > < Ext: 1 Coding: 0 Number Specified Channel Type: 3 > > < Ext: 1 Channel: 1 ] > > < [70 08 c1 34 33 39 32 38 34 32] > > < Called Number (len=10) [ Ext: 1 TON: Subscriber Number (4) NPI: > > ISDN/Telephony Numbering Plan (E.164/E.163) (1) '4392842' ] > > < [a1] > > < Sending Complete (len= 1) > > -- Making new call for cr 5377 > > -- Processing Q.931 Call Setup > > -- Processing IE 4 (cs0, Bearer Capability) > > -- Processing IE 24 (cs0, Channel Identification) > > -- Processing IE 112 (cs0, Called Party Number) > > -- Processing IE 161 (cs0, Sending Complete) > > q931.c:3509 q931_receive: call 5377 on channel 1 enters state 6 (Call > > Present) > > Sending Receiver Ready (12) > > > > -------------------------------------------------------------------------------------------------------------------- > > >-- Regards, Nasir. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081021/cdc177c2/attachment.htm