similar to: can not make call with Unicall (MFC/R2)

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Hi All, as good? I am trying to make a call for the Unicall channels and after the exchange of signalling and sending of the digits asterisk locks up with the sending of the signalling "E" and the TELCO says that asterisk would have to send signalling "F", as to make for asterisk to send signalling "F"? The TELCO says that the signalling "E" is

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Hi List, I'm trying to connect Asterisk with a Nortel Meridian using an E1 with MRFR2 signaling. I've connected both cards, and compiled all the required software... The problem is every call (outgoing or incoming) got dropped, complaining about some "T1 timed out" Only for testing purposes I'm using an application called testcall included on the lib-unicall package, and

I have a customer that is complaining that any call coming in from Nextel gives a fast busy. We are running Asterisk 1.4.7.1 with Zaptel 1.4.3 and all the MFC/R2 patches and libraries. All other calls go out and come in, just Nextel seems to have this problem. The phone company technician connected a PBX emulator on the line and that one could receive the calls from Nextel. The E1 is provided

Hello All. I'm using sangoma card A-101. tested successful with E10 (ACATEL) Exchange, connection with E1, CAS, (using unicall-0.0.3pre4). my system run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10

Hello All. I'm using sangoma card A-101. tested successful with E10 (ACATEL) Exchange, connection with E1, CAS, (using unicall-0.0.3pre4). my system run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

Hi all, I have Asterisk 1.2.10, zaptel 1.2.7, spandsp-0.0.3pre22 compiled, and a Sangoma A101, and when I make a call I get this: Jan 8 13:04:06 DEBUG[12252]: chan_unicall.c:2000 unicall_exception: Exception on 19, channel 1 Jan 8 13:04:06 WARNING[12252]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 1101 [1/ 40/Seize /Idle ] Jan 8 13:04:06 WARNING[12252]:

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line

Hello! I'm tryuing to bring up an R2 connection but eventhough I've followed the guidelines in: http://zarzamora.com.mx/asterisk/17 something seems to be missing. When an incomming call is generated I get: Nov 24 06:01:17 WARNING[-197416016]: chan_unicall.c:612 unicall_report: MFC/R2 UniCall/24 <- 0001 [1/ 1/Idle /Idle ] Nov 24 06:01:17 WARNING[-197416016]:

Hi list: I want to modify the libmfcr2. But i can't find where is define the end DNIS signal is define. Actually the libmfcr2 send a ONE (1) at the end of sending all the DNIS numbers. I need to send a TWO (2), this becouse in Mexico the normal is to send a 2 at the end, not a ONE. In the next example i dialed un 6 19:12:17 WARNING[719] chan_unicall.c: MFC/R2 UniCall/5 Call control(1)

It's bad enough that people insert long config/log files/dumps into messages to this list, though it's convenient. But when people include the entire redundant content in a quote in reply, it's really a waste. The digest messages are hard enough to navigate, even with an intro index, before making 95% of their content a redundant quoted dump. I know we've all got lots of bandwidth