Hi all, I?m using X-Lite as SoftPhone in Asterisk. I have configured this: [101] ;Turn off silence suppression in X-Lite ("Transmit Silence"=YES)! ;Note that Xlite sends NAT keep-alive packets, so qualify=yes is not needed type=friend username=jozeph callerid="Jozeph Brasil" <5678> host=dynamic nat=yes ; X-Lite is behind a NAT router canreinvite=no ; Typically set to NO if behind NAT ;disallow=all allow=gsm ; GSM consumes far less bandwidth than ulaw ;allow=ulaw ;allow=alaw When I try to connect X-Lite from another network follow this model: WORK (192.168.1.X) <-- --> FW-NAT <-- --> INTERNET <-- --> ASTERISK SERVER That machine connect OK! But, when I try to connect using this model: WORK (10.0.0.X) <-- --> 10.0.0.254 (ASTERISK SERVER) I can?t connect to the server.... why that? Asterisk Server have 2 network cards... internal and external internet card. My SIP.CONF are listen 0.0.0.0. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040725/51984d49/attachment.htm
Hello, I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to my * server via T100P card. This is the output of "status equipment" command in the Adit600: For some reason the FXO card is seen as FXS, why? Is it ok? On the card it is written "FXO". Regards, Shlomi Bachar -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040725/1b981676/attachment.htm
Shlomi Bachar wrote:> I?ve recently purchased Adit 600 with 3FXS and 1FXO to be connected to > my * server via T100P card. This is the output of ?status equipment? > command in the Adit600: > > For some reason the FXO card is seen as FXS, why? Is it ok? On the card > it is written ?FXO?. >I would ask ADIT, not the mailing list for a PBX. You could also, you know, TRY it. -- Daniel Jimenez <djimenez[at]pobox[dot]com>
Here is the output of the "status equipment" command : BootCode Version: 1.23 CardType Status SW Vers CLEI -------- ------ ------- ---- SLOT A T1x2 Present 6.1.2 SIC3DH0CAA SLOT 1 FXSx8 Present 1.09 SIC3GJ0CAA SLOT 2 FXSx8 Present 1.09 SIC3GJ0CAA SLOT 3 FXS5Gx8 Present 1.10 SIC2780JAA SLOT 4 FXSx8 Present 1.09 SIC3GJ0CAA SLOT 5 FXSx8 Not Present SLOT 6 V35x2 Not Present - Shlomi -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Shlomi Bachar Sent: Sunday, July 25, 2004 4:23 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] FXS vs. FXO Hello, I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to my * server via T100P card. This is the output of "status equipment" command in the Adit600: For some reason the FXO card is seen as FXS, why? Is it ok? On the card it is written "FXO". Regards, Shlomi Bachar -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040725/cecc8492/attachment.htm